Module assignment 6

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

need some help on this please

Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

Inclined plane diagram: Also String 1 String 2 String 1 B C A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.

The first photo is the question, where the 2nd shows some problem solving strategies

Question number 1

I just need help with part D, thanks

TOPIC: STATICS  1. Follow the rule correctly. 2. Solve the asked problem in a step-by-step procedure3. Kindly choose the correct answer on the choices4. Double-check your solutions because we need them for our review. Thank you so much for your kind consideration.

TOPIC: STATICS  1. Follow the rule correctly. 2. Solve the asked problem in a step-by-step procedure3. Kindly choose the correct answer on the choices4. Double-check your solutions because we need them for our review. Thank you so much for your kind consideration.

I need parts 3 and 4 answered pertaining to the print provided.  I asked this question previously on here and I received the wrong answers to the 2 parts Im asking about, so I am reposting the question again to have another tutor answer it.   Part 3: I need to tell what was ommited. Part 4: I need to tell what the triangle equals? Lower right or J1 zone has the answer.

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5.  1 pass 2 fail 3 fail 4 pass

Don't use chatgpt will upvote

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

Show complete and detailed solutions. Write legibly. View Image.

! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. At an intersection car B was traveling south and car A was traveling 30° north of east when they slammed into each other. Upon investigation, it was found that after the crash, the two cars got stuck and skidded off at an angle of 10° north of east. Each driver claimed that he was going at the speed limit of 50 km/h and that he tried to slow down, but couldn't avoid the crash because the other driver was going a lot faster. The masses of cars A and B were 1500 kg and 1200 kg, respectively. 10° 30° VR Determine the speed of the faster of the two cars if the slower car was traveling at the speed limit. The speed of the faster car was km/h.

|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…

Version B We have worked with Ferris Wheels above ground, but what if a portion of it went underground and traveled in a clockwise direction? Details; The Ferris Wheel has a diameter of 80 ft The Ferris Wheel center is 20 feet below the ground The Ferris Wheel rotates in a clockwise direction The rider enters on ground level on the right side of the wheel. It takes 1 minute for 1 ½ rotations. Your task: Determine the angular speed. Develop an equation for the height of the rider while on the ride. Calculate the rider's total distance traveled from the moment they get on at ground level on the right to the other point on ground level on the left where they get off.