Explanation Draw the T − s diagram for the simple ideal Brayton cycle as shown in Figure (1). Write the expression to calculate the specific volume at state 1 v 1 . v 1 = R T 1 P 1 (I) Here, gas constant is R , temperature at state 1 is T 1 and pressure at state 1 is P 1 . Write the expression to calculate the mass flow rate. m ˙ = A 1 V 1 v 1 (II) Here, area at which argon enters the compressor is A 1 and initial velocity is V 1 . Write the temperature and pressure relation for the isentropic process 1-2. T 2 = T 1 ( P 2 P 1 ) ( k − 1 ) / k (III) Here, the specific heat ratio is k , temperature at state 1 is T 1 , temperature at state 2 is T 2 and pressure at state 2 is P 2 . Write the temperature and pressure relation for the isentropic process 3-4. T 4 = T 3 ( P 4 P 3 ) ( k − 1 ) / k (IV) Here, temperature at state 4 is T 4 , temperature at state 3 is T 3 , pressure at state 4 is P 4 . And pressure at state 4 is P 4 . Write the expression to calculate the net power produced by the cycle ( W ˙ n e t ) . W ˙ n e t = m ˙ c p [ T 3 − T 4 − T 2 − T 1 ] (V) Here, heat capacity of air is c p , and mass flow rate of air is m ˙ a i r . Write the expression to calculate the heat addition rate to the cycle ( Q ˙ i n ) . Q ˙ i n = m ˙ a i r c p ( T 3 − T 2 ) (VI) Write the expression to calculate the rate of heat rejection in the cycle ( Q ˙ o u t ) . Q ˙ o u t = Q ˙ i n − W ˙ net (VII) Write the expression to calculate the rate of entropy generated by the cycle ( S ˙ g e n ) S ˙ g e n = Q ˙ o u t T L − Q ˙ i n T H (VII) Here, the high temperature of the hot or higher state is T H , and the temperature of cold or lower state is T L . Conclusion: From Table A-1E, “Molar mass, gas constant, and critical-point properties”, obtain the value of gas constant ( R ) for argon as 0.2686 psia ⋅ ft 3 / lbm ⋅ R . From Table A-2Ea, “Ideal-gas specific heats of various common gases”, obtain the value of specific heat ratio ( k ) for argon as 1.667 . Substitute 0.2686 psia ⋅ ft 3 / lbm ⋅ R for R , 80 ° F for T 1 and 15 psia for P 1 in Equation (I). v 1 = 0.2686 psia ⋅ ft 3 / lbm ⋅ R ( 80 ° F ) 15 psia = 0.2686 psia ⋅ ft 3 / lbm ⋅ R ( 80 + 460 ) R 15 psia = 9.670 ft 3 / lbm Substitute 3 ft 3 for A 1 , 200 ft / s for V 1 and 9.670 ft 3 / lbm for v 1 in Equation (II). m ˙ = 3 ft 3 × 200 ft / s 9.670 ft 3 / lbm = 62.05 lbm / s Substitute 150 psia 6 for P 2 , , 15 psia for P 1 , 80 ° F for T 1 and 1.667 for k in Equation (III). T 2 = 80 ° F ( 150 psia 15 psia ) ( 1.667 − 1 ) / 1.667 = ( 80 + 460 ) R ( 150 psia 15 psia ) ( 0

9th Edition

ISBN: 9781307573022

Author: CENGEL

Publisher: MCG/CREATE

See similar textbooks

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its m…

Videos

Question

Chapter 9.12, Problem 146P

To determine

The rate of entropy generated by the cycle.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.12, Problem 145P

Chapter 9.12, Problem 147P

Students have asked these similar questions

A gas turbine operates in an ideal Brayton cycle of which Argon is used as the working substance. During the start of the compression, the temperature of the gas is at 340 K and pressure of 500kPa. The compression process is adiabatic with gas conditions at the outlet of 650 K and 1930 kPa. The working substance is heated and entered the turbine at 1400 K and 1930kPa and expands adiabatically to 900 K and 490kPa. Determine the compressor and turbine efficiencies, the actual compressor and turbine work, the net work of the cycle, the thermal efficiency, and the new thermal efficiency when assuming that a regenerator is installed with 85% effectiveness. Draw the schematic diagram.

A four-cylinder, four-stroke, 1.6-L gasoline engine operates on the Otto cycle with a compression ratio of 11. The air is at 100 kPa and 37°C at the beginning of the compression process, and the maximum pressure in the cycle is 8 MPa. The compression and expansion processes may be modeled as polytropic with a polytropic constant of 1.3. Using constant specific heats at 850 K, determine the engine speed for a net power output of 50 kW.

In an Otto cycle engine, air at 1 bar and 50°C is compressed until the pressure reaches 650 KPa. Heat is added during the constant volume process at a rate of 500 kJ/kg. Determine the compression ratio of the engine, the temperature at the end of compression and at the end of heat addition. Also determine the maximum possible compression ratio for this cycle. Take cp = 1.0 kJ/kg-K, cv = 0.706kJ/kg-K.

Chapter 9 Solutions

THERMODYNAMICS-SI ED. EBOOK >I<

Ch. 9.12 - What are the air-standard assumptions?Ch. 9.12 - What is the difference between air-standard...Ch. 9.12 - Prob. 3P Ch. 9.12 - How does the thermal efficiency of an ideal cycle,...Ch. 9.12 - How are the combustion and exhaust processes...Ch. 9.12 - What does the area enclosed by the cycle represent...Ch. 9.12 - Prob. 7P Ch. 9.12 - Can the mean effective pressure of an automobile...Ch. 9.12 - What is the difference between spark-ignition and...Ch. 9.12 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The rate of entropy generated by the cycle.

Solution Summary: The author analyzes the rate of entropy generated by the Brayton cycle.

Concept explainers

Videos

The rate of entropy generated by the cycle.

Want to see the full answer?

Chapter 9 Solutions