ENGINEERING MECHANICS Â?? STATICS
15th Edition
ISBN: 9780137519132
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 9.1, Problem 36P
Locate the centroid ȳ of the shaded area.
Probs. 9-35/36
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A converging elbow (see the figure below) turns water through an angle of 135° in a vertical plane. The flow cross section diameter is
400 mm at the elbow inlet, section (1), and 200 mm at the elbow outlet, section (2). The elbow flow passage volume is 0.2 m³ between
sections (1) and (2). The water volume flowrate is 0.1 m³/s and the elbow inlet and outlet pressures are 140 kPa and 90 kPa. The elbow
mass is 11 kg. Calculate the (a) horizontal (x direction) and (b) vertical (z direction) anchoring forces required to hold the elbow in
place.
D₂-
Section
(1)-
D₁ = 400 mm
135°
200 mm
Section (2)
(a) Fx= i
20809.96
N
(b) Fz= i
-120265
N
2: A rectangular aluminum block is loaded uniformly in three directions. The loadings are as follows:a 50 kN total resulting compressive load in the x-direction, a 200 kPa uniformly distributed tensile load in they-direction, and a 0.03 MN total resulting tensile load in the z-direction. The block has the following dimensions:L = 1 m, b = 20 cm, h = 350 mm. Use E = 70 GPa and ν = 0.25.Determine the strain in the x and y axes respectively. For the strain in the y-direction to be equal to 0, how much uniformly distributed load inthe surface of y-direction should be added? (+ for tensile, - for compressive)
Answers:
5 -1.122 x10-5 / 3 decimals
6 5.102 x10-6 / 3 decimals
7 -0.357 MPa / 3 decimals
A spherical balloon with a diameter of 9 m is filled with water vapour at 200˚C and 200 kPa. Determine the mass of water in the balloon. The R value for water is 0.4615 kJ/kg∙K.
Chapter 9 Solutions
ENGINEERING MECHANICS Â?? STATICS
Ch. 9.1 - In each case, use the element shown and specify...Ch. 9.1 - Determine the centroid (x,y) of the shaded area....Ch. 9.1 - Determine the centroid (x,y) of the shaded area....Ch. 9.1 - Determine the centroid of the shaded area. Prob....Ch. 9.1 - Locate the center of mass x of the straight rod if...Ch. 9.1 - Locate the centroid of the homogeneous solid...Ch. 9.1 - Locate the centroid z of the homogeneous solid...Ch. 9.1 - Locate the center of mass of the homogeneous rod...Ch. 9.1 - Determine the location (x,y) of the centroid of...Ch. 9.1 - If the rod has a weight per unit length of 100...
Ch. 9.1 - Locate the center of gravity of the homogeneous...Ch. 9.1 - Determine the distance to the center of gravity...Ch. 9.1 - Locate the centroid of the area.Ch. 9.1 - Locate the centroid x of the parabolic area. Prob....Ch. 9.1 - Locate the centroid of the shaded area. Prob. 9-8Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the area. Probs. 9-11/12Ch. 9.1 - Locate the centroid of the area. Probs. 9-11/12Ch. 9.1 - Locate the centroid x of the area. Probs. 9-13/14Ch. 9.1 - Locate the centroid of the area. Probs. 9-13/14Ch. 9.1 - Solve the problem by evaluating the integrals...Ch. 9.1 - Solve the problem by evaluating the integrals...Ch. 9.1 - Locate the centroid of the area. Prob. 9-17Ch. 9.1 - Locate the centroid x of the area. Probs. 9-18/19Ch. 9.1 - Locate the centroid of the area. Probs. 9-18/19Ch. 9.1 - Locate the centroid of the shaded area.Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Determine the location of its center of gravity....Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the area. Probs. 9-32/33Ch. 9.1 - Locate the centroid of the area. Probs. 9-32/33Ch. 9.1 - Determine the location of its center of mass. Also...Ch. 9.1 - Locate the centroid x of the shaded area. Probs....Ch. 9.1 - Locate the centroid of the shaded area. Probs....Ch. 9.1 - Locate the centroid x of the circular sector.Ch. 9.1 - Determine the location r of the centroid C for the...Ch. 9.1 - The material is homogeneous. Prob. 9-39Ch. 9.1 - Locate the centroid of the paraboloid. Probs....Ch. 9.1 - Locate the centroid z of the frustum of the...Ch. 9.1 - Determine the centroid of the solid. Prob. 9-42Ch. 9.1 - Locate the centroid of the quarter-cone. Prob....Ch. 9.1 - Determine its mass and the distance z to the...Ch. 9.1 - Locate the centroid z of the volume. Prob. 9-45Ch. 9.1 - Locate the centroid of the ellipsoid of...Ch. 9.1 - Locate the center of gravity z of the solid. Prob....Ch. 9.1 - Locate the centroid of the ellipsoid of...Ch. 9.1 - Locate the centroid z of the spherical segment....Ch. 9.1 - Suggestion: Use a triangular plate element...Ch. 9.2 - Locate the centroid (x,y,z) of the wire bent in...Ch. 9.2 - Locate the centroid of the beams cross-sectional...Ch. 9.2 - Locate the centroid of the beams cross-sectional...Ch. 9.2 - Locate the centroid (x,y) of the cross-sectional...Ch. 9.2 - Locate the center of mass (x,y,z) of the...Ch. 9.2 - Determine the center of mass (x,y,z) of the...Ch. 9.2 - If the mass of the gusset plates at the joints and...Ch. 9.2 - Determine the location (x,y,z) of the centroid of...Ch. 9.2 - Determine the location (x,y) of the centroid of...Ch. 9.2 - Neglect the thickness of the material and slight...Ch. 9.2 - Neglect the thickness of the material and slight...Ch. 9.2 - Each plate has a constant width in the z direction...Ch. 9.2 - Neglect the thickness of each segment. The mass...Ch. 9.2 - Neglect the size of the corner welds at A and B...Ch. 9.2 - Prob. 59PCh. 9.2 - Locate the centroid for the beams cross-sectional...Ch. 9.2 - Determine the location of the centroid C of the...Ch. 9.2 - Locate the centroid (x,y) of the shaded area....Ch. 9.2 - Neglect the size of the corner welds at A and B...Ch. 9.2 - Locate the centroid (x,y) of the shaded area....Ch. 9.2 - Determine the location (x,y) of the centroid C of...Ch. 9.2 - The beam is symmetric with respect to the y axis....Ch. 9.2 - Assume all corners are square and neglect the size...Ch. 9.2 - Prob. 68PCh. 9.2 - If it is folded over as shown, determine the...Ch. 9.2 - Locate the center of mass z of the forked level...Ch. 9.2 - Prob. 71PCh. 9.2 - Prob. 72PCh. 9.2 - Prob. 73PCh. 9.2 - The location of the center of gravity of each...Ch. 9.2 - Locate the center of mass (x,y,z) of the...Ch. 9.2 - Determine the location (x,y,z) of its centroid....Ch. 9.2 - It the cord is cut, the part will rotate about the...Ch. 9.2 - Prob. 78PCh. 9.2 - Prob. 79PCh. 9.2 - Prob. 80PCh. 9.2 - The assembly is made from a steel hemisphere. st =...Ch. 9.2 - The assembly is made from a steel hemisphere, st =...Ch. 9.2 - Prob. 83PCh. 9.2 - Determine the distance h to which a...Ch. 9.2 - Determine the distance z to the centroid of the...Ch. 9.2 - The cylinder and the cone are made from materials...Ch. 9.2 - Major floor loadings in a shop are caused by the...Ch. 9.2 - Determine the distance x to its center of gravity...Ch. 9.2 - Determine the mass and location (x,y,z) of its...Ch. 9.3 - Determine the surface area and volume of the solid...Ch. 9.3 - Prob. 14FPCh. 9.3 - Determine the surface area and volume of the solid...Ch. 9.3 - Determine the surface area and volume of the solid...Ch. 9.3 - Prob. 90PCh. 9.3 - Prob. 91PCh. 9.3 - Determine the volume of the storage tank. Probs....Ch. 9.3 - Prob. 93PCh. 9.3 - Determine the total weight of the wall if the...Ch. 9.3 - Determine its volume.Ch. 9.3 - Prob. 96PCh. 9.3 - Determine the volume of concrete needed to...Ch. 9.3 - Do not include the area of the ends in the...Ch. 9.3 - Prob. 99PCh. 9.3 - Prob. 100PCh. 9.3 - Prob. 101PCh. 9.3 - Each gallon of paint can cover 250 ft2. Probs....Ch. 9.3 - Determine the surface area and the volume of the...Ch. 9.3 - Prob. 104PCh. 9.3 - Determine how many joules (J) are radiated within...Ch. 9.3 - Prob. 106PCh. 9.3 - Prob. 107PCh. 9.3 - Prob. 108PCh. 9.3 - Prob. 109PCh. 9.3 - Prob. 110PCh. 9.3 - Prob. 111PCh. 9.3 - Prob. 112PCh. 9.3 - Prob. 113PCh. 9.3 - Prob. 114PCh. 9.5 - Water has a density of = 1 Mg/m3. Prob. F9-17Ch. 9.5 - The specific weight of water is = 62.4 lb/ft3.Ch. 9.5 - Water has a density of = 1 Mg/m3. Prob. F9-19Ch. 9.5 - Water has a density of = 1 Mg/m3. Prob. F9-20Ch. 9.5 - The specific weight of water is = 62.4 lb/ft3....Ch. 9.5 - Determine the magnitude of the resultant force and...Ch. 9.5 - Determine the magnitude of the resultant force and...Ch. 9.5 - The load over the plate varies linearly along the...Ch. 9.5 - The load is defined by the expression p = p0 sin...Ch. 9.5 - If this pressure loading acts uniformly along the...Ch. 9.5 - For the condition of high tide shown, determine...Ch. 9.5 - Determine the resultant force the water exerts on...Ch. 9.5 - If the density of concrete is c = 2.5 Mg/m3, and...Ch. 9.5 - Determine this factor if the concrete has a...Ch. 9.5 - Determine the magnitude of the resultant...Ch. 9.5 - If it is filled to the top, determine the...Ch. 9.5 - Prob. 126PCh. 9.5 - Determine the reactions at these supports due to...Ch. 9.5 - The tank is filled with a liquid that has a...Ch. 9.5 - The gate has a width of 1.5 m. w = 1.0 Mg/m3....Ch. 9.5 - Prob. 130PCh. 9.5 - Locate the centroid x of the area.Ch. 9.5 - Locate the centroid of the area.Ch. 9.5 - Prob. 3RPCh. 9.5 - Locate the centroid of the rod. Prob. R9-4Ch. 9.5 - Prob. 5RPCh. 9.5 - Prob. 6RPCh. 9.5 - Determine the volume of material required to make...Ch. 9.5 - Prob. 8RPCh. 9.5 - Determine the horizontal and vertical components...Ch. 9.5 - Determine the magnitude of the resultant...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Correct answers are written below. Detailed and correct solution only with fbd. I will upvote. 1: A 3 m alloy shaft fixed at one end has a torsional shearing stress capacity of 55 MPa. Due to improper fabrication, its cross-sectionalarea has become irregularly shaped. Its effective polar moment of inertia has become 2 x10-7 m4, and the maximum torque stress acts at 7.5 cm fromthe center of the shaft.[1]: If the shaft is to be replaced by a properly manufactured solid circular shaft that has a maximumshearing stress capacity of 70 MN/m2, what is the minimum diameter required so it can withstand the sameload? [2]: Calculate the thickness of a hollow circular shaft with the same outside diameter calculated initem [1] that can carry the same load. Limit the maximum shearing stress of the hollow circular shaft to0.09 GPa.Determine the angle of twist on the free end of the shaft. Use G = 150 x103 GPa. [3]: Use the solidcircular shaft from [1] and use the hollow circular shaft from [2].…arrow_forwardtwo closed 1 m3 chambers are filled with fluid at 25˚C and 1 atm. One is filled with pure carbon dioxide and one is filled with pure water. Only considering the weight of the fluids, which chamber is heavier?arrow_forwardCorrect answers are written below. Detailed and correct solution only with fbd. I will upvote. 1: A 3 m alloy shaft fixed at one end has a torsional shearing stress capacity of 55 MPa. Due to improper fabrication, its cross-sectionalarea has become irregularly shaped. Its effective polar moment of inertia has become 2 x10-7 m4, and the maximum torque stress acts at 7.5 cm fromthe center of the shaft.[1]: If the shaft is to be replaced by a properly manufactured solid circular shaft that has a maximumshearing stress capacity of 70 MN/m2, what is the minimum diameter required so it can withstand the sameload? [2]: Calculate the thickness of a hollow circular shaft with the same outside diameter calculated initem [1] that can carry the same load. Limit the maximum shearing stress of the hollow circular shaft to0.09 GPa.Determine the angle of twist on the free end of the shaft. Use G = 150 x103 GPa. [3]: Use the solidcircular shaft from [1] and use the hollow circular shaft from [2].…arrow_forward
- In using the bolt cutter shown, a worker applies two forces P to the handles. If the magnitude ofP is 500 N, determine the magnitude of the forces exerted by the cutter on the boltarrow_forwardArterioles bifurcate (i.e., split) into capillaries in the circulatory system. Blood flows at a velocity of 20 cm/s through an arteriole with a diameter of 0.20 cm. This vessel bifurcates into two vessels: one with a diameter of 0.17 cm and a blood flow velocity of 18 cm/sec, and one with a diameter of 0.15 cm. Each of these two vessels splits again. The 0.17-cm diameter vessel splits into two vessels, each with a diameter of 0.15 cm. The 0.15-cm diameter vessel splits into two vessels, each with a diameter of 0.12 cm. Determine the mass flow rate and velocity of blood in each of the four vessels at the end of the arteriole bifurcations. You may need to set up several systems, each with a different system boundary, in order to solve this problem.arrow_forward6) Draw a Front, side and Top view for the following objects: p.s. you don't need to label the alphabet ISOMETRIC PICTORIAL VIEW K R C B E R D 0 Aarrow_forward
- Please draw the front top and side view for the following objectarrow_forwardDraw the top viewarrow_forwardSuppose that a steel of eutectoid composition is cooled to 675°C (1250°F) from 760°C (1400°F) in less than 0.5 s and held at this temperature. (a) How long will it take for the austenite-topearlite reaction to go to 50% completion? To 100% completion? (b) Estimate the hardness of the alloy that has completely transformed to pearlite.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Mechanical Engineering: Centroids & Center of Gravity (1 of 35) What is Center of Gravity?; Author: Michel van Biezen;https://www.youtube.com/watch?v=Tkyk-G1rDQg;License: Standard Youtube License