Concept explainers
Find the average velocity of the water leaving the tank.
Answer to Problem 39P
The average velocity of the leaving water in
Explanation of Solution
Given data:
Refer to the given Figure Problem 9.38 in the textbook, which shows the tank is filled by water using pipes 1 and 2.
The water level increases in the rate of 0.1 in/s.
The diameter of the tank is
Formula used:
Write the expression for the volume flow rate.
Here,
Calculation:
Consider that the constant water density.
From the given figure, write the volume flow rate expression for inlet and outlet volumetric flow rate expressions.
Re-arrange the equation,
Substitute
The values of
And
Convert the unit of value in equation (1) from
Convert the unit of value in equation (1) from
Conclusion:
Hence, the average velocity of the leaving water in
Want to see more full solutions like this?
Chapter 9 Solutions
Engineering Fundamentals
- The below equations describe the velocity components in a flow field: v = 4y3z, Please estimate the total acceleration of the fluid at the location x=lm, y=1m, z=0.5m when u = x?y, w = 3t t=2s.arrow_forwardWater flows through the Venturi meter as shown in the figure below. The specific gravity of the manometer fluid is 1.52. Determine the flow rate in feet cubed per second. 2 in. SG= 1.52arrow_forward0.2 m³/sec of fluid passes through a pipe with diameter 41 centimeters. Determine the fluid's average speed in meters/sec. Your answer should include at least one digit after the decimal place.arrow_forward
- Q1(c) Water flows horizontally through a nozzle into the atmosphere under certain conditions, as shown in Figure Q1(c). Calculate: (i) Volume flow rate of water flowing through the nozzle in m3/s and L/s, respectively. (ii) Mass flow rate of water. (iii) Exit velocity at the outlet of the nozzle.arrow_forwardAir flows past an objects and exits as a free jet as shown in the figure. Because of the obstruction, the exit velocity is non-uniform with magnitude of 4 m/s from r = 0 m to r = 0.5 m and 12 m/s fromr = 0.5 m to r = 1.0 m. Using a differential area, dA = 2rrdr, what is the value of the volumetric flow rate in m3/s? Air 4 m/s 2-m-dia. Wake 1-m dia 12 m/s Exit Answer:arrow_forwardIn an air flow the velocity is measured by a Pitot tube (coefficient = 1.0). The mass density of air can be taken as 1.2 kg/m³. If the head difference in a vertical U-tube holding water is 12 mm, then what is the velocity of air in m/s?arrow_forward
- 1. A fluid (s=0.9) flows through a 75 mm diameter pipe at a velocity of 6 m/sec. Compute the Volume flow rate. (m3/s) Round your answer to 4 decimal places.arrow_forward1) A tank has a single inflow and two outflows as shown in the figure. The water surface in the tank is open to the atmosphere. a. Is the tank in the figure filling or emptying? b. At what rate is the water level rising or falling in the tank? 4 in. diameter V = 10 ft/s 6 ft diameter Water V=7 ft/s 3 in. diameter V=4 ft/s 6 in. diameterarrow_forward19arrow_forward
- A fluid is between two parallel horizontal plates as depicted above. The bottom plate is stationary while the top plate is moving to the right with speed 7.6 feet/second. The top plate is 2 inches above the bottom plate. Determine the velocity gradient for the fluid in feet/second velocity increase per foot rise above the bottom plate. Your answer should include at least 1 digit after the decimal place.arrow_forwardThe tank shown in the accompanying figure is being filled by Pipes 1 and 2. If the water level is to remain constant, what is the mass-flow rate of water leaving the tank at Pipe 3? What is the average velocity of the water leaving the tank? Pipe 1: di =1 in. V = 2 ft/s Pipe 2: d = 1.75 in. V = 1.5 fUs Pipe 3: d3 = 1.5 in. V = ?arrow_forward8. Compute the probable density of a fluid inside a floating spherical balloon having a 2m diameterif the tension in the balloon’s tie rope is observed to be 2kgf. Assume that the density of air is1.18kg/m3. a. 0.7225kg/m3 b. 0.6225kg/m3 c. 0.7025kg/m3 d. 0.5848kg/m3arrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning