EBK STRUCTURAL ANALYSIS
5th Edition
ISBN: 9780100469105
Author: KASSIMALI
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 9, Problem 21P
To determine
Find the absolute maximum bending moment in a 75 ft long simply supported beam.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Q.2 The required design span for the beam given in Q.1 is increased to 18 ft. The design loads
are the same as given in Q.1 Check the adequacy of a 10"x16" 10 Caribbean Pitch Pine –
(Select Structural) for this these design conditions.
The timber floor framing for a building comprise floor joists using 2" wide nominal lumber
is to be constructed as shown in Fig. 1. The Dead load (D) = 26 lbs./ft² (inclusive of joists
and flooring) and the live load L= 40 lbs./ft². Lateral torsional buckling is prevented for all
members and normal service conditions and temperatures are expected.
(i) Design the floor joists using 2" wide nominal lumber using Southern Pine No. 1
(ii) Design the floor beams using Caribbean Pitch Pine (Select Structural). (Assume a 8" x
14” trial section to estimate beam self-weight for your initial design). Density of
Caribbean Pitch Pine = 50 lbs/ft³ (800 kN/m³).
P12.38 WP At a point on the free surface of a stressed body, a normal stress of 64 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 8 MPa (C). The absolute maximum shear stress at the point has a
magnitude of 95 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point.
Chapter 9 Solutions
EBK STRUCTURAL ANALYSIS
Knowledge Booster
Similar questions
- A pile group of 25 piles has to be proportioned in a uniform pattern in soft clay with equal spacing in all directions. Assuming the value of cu to be constant throughout the depth of the piles, determine the optimum value of spacing of piles in the group. Assume a = 0.7. Neglect point bearing effect, and assume the piles to be circular.arrow_forwardExample 5 By using the yield line theory, determine the moment (m) for an isotropic reinforced concrete two-way slab (supports on two S.S sides shown in figure under the load (P) (all dimensions are in mm). Solve by using equilibrium method m m 3000 2000 2000arrow_forwardA +7.5% grade meets a horizontal grade on a section of a rural mountainous highway. If the length of the crest vertical curve formed in that section is 300 ft long, determine the safe operating speed on the highway.arrow_forward
- A sawn timber beam of dimensions 8"x14" has is required for a span of 16 ft. The uniformly distributed loads are Dead (D) = 350 lbs./ft and live (L) = 400 lbs./ft. The dead load includes the beam self-weight and lateral torsional buckling is prevented. The beam is to be used in an indoor environment (MC > 19º) in normal temperatures. Using Caribbean Pitch Pine (Select Structural), check that the section chosen is adequate.arrow_forward2. Find the moment of inertia and radius of gyration about the coordinate axes of a thin rectangular plate of constant density bounded by the lines x=3 and y = 3 in the first quadrant.arrow_forwardVehicle begin to arrive at a parking lot at 6:00 am at a rate of 8 per minute. No vehicles arrivefrom from 6:20 to 6:30 am. From 6:30 am on vehicle arrive at a rate of 2 veh/min. The parkinglot attendant processes incoming vehicles at a rate of 4 veh/min throughout day. AssumingD/D/1 queue, determine total vehicle delayarrow_forward
- A cantilever beam 12 ft long supports a uniform service superimposed deadload of 1 kip/ft, and a concentrated service live load of 14 kip at the free end. Theconcrete compressive strength is 4 ksi, and the steel yield strength is 60 ksi. Thebeam section at the support is shown. Find the adequacy of the section inresisting bending moment at the support.arrow_forwardu(t) (Uss) -1 a/w = 1.0 M 1 2 3 Tarrow_forwardplease helparrow_forward
- Please use MATLAB with codes and figures.Recreate the following four Figures of the textbook using MATLAB and the appropriate parameters. Comment on your observations for each Figure. List all of the parameters that you have used. The figures are attached belowarrow_forwardA simply supported beam for a building interior with 18 ft span has a cross section of 12 in width and 21 in overall depth. The beam is made with 5 ksi compressive strength concrete and 60 ksi reinforcing steel. The beam supports a uniform service superimposed dead load of 1.6 kip/ft, and a uniform service live load of 80 psf throughout the span. The beams are laterally spaced 20 ft apart c/c. Design this beam and show in a sketch.arrow_forwardThe dam presented below is 180 m long (in the direction perpendicular to the plane of the cross-section). For the water elevations given on the drawing: a) Construct the flow net (minimum number of equipotential lines should be 10), b) Calculate the rate of seepage for the entire dam, c) Find the total uplift force on the dam (ignore barriers), and d) Estimate the hydraulic gradient at points A, B, and D. Recommended to use a spreadsheet to include all equations for calculations of potentials.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning