MAT.SCIENCE+ENGIN.(PERUSALL ACCESS)
MAT.SCIENCE+ENGIN.(PERUSALL ACCESS)
10th Edition
ISBN: 2818440149658
Author: Callister
Publisher: PERUSALL
Question
Book Icon
Chapter 9, Problem 1QAP

(a)

To determine

The mass of sugar dissolved in mw=1500g water at T=90oC .

(a)

Expert Solution
Check Mark

Answer to Problem 1QAP

The mass of sugar dissolved in mw=1500g water at T=90oC is ms=5.022kg .

Explanation of Solution

Given Amount of water is mw=1500g .

Temperature is T=90oC .

Formula used:

  Csugar=msugarmsugar+mwater×100%

Where,

  Csugar is the composition of sugar in weight percent.

  msugar is the mass of sugar.

  mwater is the mass of water.

  MAT.SCIENCE+ENGIN.(PERUSALL ACCESS), Chapter 9, Problem 1QAP , additional homework tip  1

According to diagram Csugar=77

  %wtsugar

Calculations Put value of Csugar=77 , mass of water= 1500g

  Csugar=msugarmsugar+mwater×100%77=msugarmsugar+1500kgx100%0.77=msugarmsugar+1500kgmsugar=0.77msugar+1500kg0.23msugar=1155kgmsugar=5.022kg

Conclusion So, the mass of sugar dissolved in mw=1500g water at T=90oC .is ms=5.022kg .

(b)

To determine

Composition of saturated liquid solution at T=20°C .

(b)

Expert Solution
Check Mark

Answer to Problem 1QAP

Composition of the saturated liquid solution is C=65%wt .

Explanation of Solution

From the sugar-water phase diagram when the liquid saturated solution from temperature T=90°C is cooled to temperature T=20°C then the composition of the saturated liquid solution is C=65%wt . It is shown in the graph below.

  MAT.SCIENCE+ENGIN.(PERUSALL ACCESS), Chapter 9, Problem 1QAP , additional homework tip  2

Conclusion Hence, the composition of the saturated liquid solution is C=65%wt .

(c)

To determine

Mass of solid sugar comes out of the solution upon cooling to T=20°C .

(c)

Expert Solution
Check Mark

Answer to Problem 1QAP

Mass of solid sugar comes out of the solution upon cooling to T=20°C is msolidified=2.714kg .

Explanation of Solution

Given Amount of water is mw=1500g .

Cooling Temperature is T=20°C .

Mass of sugar dissolved at T'=90°C is ms=5.022kg .

Formula used:

Solubility of sugar in water is given by:

  CsugarT=20°C=m'sugarm'sugar+mwaterx100%

Where,

  Csugar =Composition of sugar in weight percent

  m'sugar =mass of maximum solubility of sugar at T=20°C .

  mwater =mass of water

Mass of sugar solidifies upon cooling to temperature T=20°C is

  msolidified=msugarT'=90°Cm'sugarT=20°C

  MAT.SCIENCE+ENGIN.(PERUSALL ACCESS), Chapter 9, Problem 1QAP , additional homework tip  3

According to diagram Csugar=65%wt sugar

Calculations Put value of Csugar=65 , mass of water mw=1500g

  CsugarT=20°C=m'sugarm'sugar+mwater×100%65=m'sugarm'sugar+1500g×100%m'sugarm'sugar+1500g=0.65m'sugar=0.65m'sugar+1500g0.35m'sugar=975gm'sugar=975g0.35m'sugar=2785.72gm'sugar=2.786kg

Mass of sugar solidifies upon cooling to temperature T=20°C is

  msolidified=msugarT'=90°Cm'sugarT=20°Cmsolidified=5.5kg2.786kgmsolidified=2.714kg

Conclusion So, the mass of sugar that solidified upon cooling to temperature T=20°C is msolidified=2.714kg .

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. 12: A steel cantilever beam 16 ft 8 in in length is subjected to a concentrated load of 320 lb acting at the freeend of the bar. A commercially available rolled steel section, designated as W12x32, is used for the beam. Assume that the total depth of the beam is 12 in, and the neutral axis of the section is in the middle. Determine the maximum tensile and compressive stresses. (Properties of commercially available rolled steel section provided in the table. Z = section modulus). ANS: σT = σC = 1,572.482 lb/in2
CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. 14: Two ½-in x 8-in cover plates are welded to two channels 10 in high to formthe cross section of the beam shown in Fig. 8-59. Loads are in a vertical plane and bendingtakes place about a horizontal axis. The moment of inertia of each channel about ahorizontal axis through the centroid is 78.5 in4. If the maximum allowable elastic bendingstress is 18,000 lb/in2, determine the maximum bending moment that may be developedin the beam.ANS: 1,236,000 lb-in.
CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. 11: A beam of circular cross section is 7 in in diameter. It is simply supported at each end and loaded by twoconcentrated loads of 20,000 lb each, applied 12 in from the ends of the beam. Determine the maximum bending stressin the beam. ANS: σ = 7,127.172 lb/in2
Knowledge Booster
Background pattern image
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
MATLAB: An Introduction with Applications
Engineering
ISBN:9781119256830
Author:Amos Gilat
Publisher:John Wiley & Sons Inc
Text book image
Essentials Of Materials Science And Engineering
Engineering
ISBN:9781337385497
Author:WRIGHT, Wendelin J.
Publisher:Cengage,
Text book image
Industrial Motor Control
Engineering
ISBN:9781133691808
Author:Stephen Herman
Publisher:Cengage Learning
Text book image
Basics Of Engineering Economy
Engineering
ISBN:9780073376356
Author:Leland Blank, Anthony Tarquin
Publisher:MCGRAW-HILL HIGHER EDUCATION
Text book image
Structural Steel Design (6th Edition)
Engineering
ISBN:9780134589657
Author:Jack C. McCormac, Stephen F. Csernak
Publisher:PEARSON
Text book image
Fundamentals of Materials Science and Engineering...
Engineering
ISBN:9781119175483
Author:William D. Callister Jr., David G. Rethwisch
Publisher:WILEY