FUND OF ENG THERMODYN(LLF)+WILEYPLUS
9th Edition
ISBN: 9781119391777
Author: MORAN
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Question
error_outline
This textbook solution is under construction.
Students have asked these similar questions
Consider a simple ideal Rankine cycle and an ideal regenerative Rankine cycle with one open feedwaterheater. The two cycles are very much alike, except the feedwater in the regenerative cycle is heated byextracting some steam just before it enters the turbine. Compare the efficiencies of these two cycles. Showyour complete solution and diagram’s.
A Carnot cycle has been chosen as a candidate for the ideal vapor power cycle. The pump inlet is a saturated liquid and the minimum and maximum pressures are set. The minimum pressure is 10 kPa and the maximum pressure is 10 MPa. Check all that will are correct
Group of answer choices
The minimum pump work will be about 5 kJ/kg
The efficiency of the Carnot cycle will be greater than the efficiency of a Rankine cycle with the same minimum and maximum pressures
The difference between the maximum and minimum temperature will be small and the thermal efficiency will be low.
The minimum pump work will be about 10 kJ/kg
Please solve this problem. Thank you
Knowledge Booster
Similar questions
- Prove that there is an increase in efficiency between a Simple Rankine Cycle and a Reheat Rankine Cycle. What is worth using for considering the efficiency?arrow_forwardConsider an ideal gas-turbine cycle with the following details in Table 1. Table 1 No. of stages at compression No. of stages at expansion 2 2 Pressure ratio 3 T of air at compressor inlet T of air at turbine inlet 300 K 1200 K Analyse the back work ratio and compare the thermal efficiency of the cycle for these two cases: i. no regenerator is used ii. a regenerator is used with 75 percent effectivenessarrow_forwardConsidering that the change in enthalpy at the first stage of a Reheat Rankine Cycle is 450 BTU/lb and 850 BTU/lb was recorded in the second stage, calculate for the thermal efficiency (in percent) of the cycle if both stages has a 93% efficiency and having a heat added of 9000 kJ/kg. (Hint: Neglect the pump work)arrow_forward
- Explain how the turbine work output, heat supplied, heat rejected and moisture content at turbine exit change when regeneration is added to a simple ideal Rankine cycle.arrow_forwardConstruct the ideal Rankine cycle with three stages of reheating on a T-s diagram. Assume the turbine inlet temperature is the same for all stages. Justify how does the cycle efficiency vary with the number of reheat stages.arrow_forwardan ideal Rankine cycle (fluid flow rate is 8 kg/s) operating between upper and lower pressures of 5 and 10,000 kPa. Draw a schematic of the components of this cycle. Draw the cycle on a P-v phase diagram and a T-s diagram. Find the power output of the turbine, the power input needed for the pump, and the overall cycle thermal efficiency.arrow_forward
- Correct and complete solution pleasearrow_forwardA gas turbine power plant working on Brayton cycle, Explain the working principle of the cycle with physical diagram as well as P-V and T-s diagrams, and with all the required detailsarrow_forwardProvide the given, manual step by step solution, and diagram. A Carnot cycle has an efficiency of 60 %. The heat added is 1000 KJ.What is the heat rejected from the cycle?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY