The final properties of A 3105 aluminum plate which is reduced from 1 .75 in to 1 .15 in should be determined. Concept Introduction: At subzero temperature, the aluminium/ aluminum A 3105 alloy has higher strength. It also has high ductility. This alloy is made up of 98% of pure aluminum. This alloy hasthe following properties: Corrosion resistnce is high Good in weldability Good in formabilty Density of the aluminimum alloy is 2 .6-2 .8 g/cm³ and the melting temperature is 641 ° C . Th aluminium alloys is made up of 99 .0 % of Aluminium (Al), 0 .55 % of Mangnese (Mn) and 0 .50 % of Magnesium(Mg)

Question

3. What is the function of LM565 pin 6? 4. What is the purpose of the multistage low-pass filter between the LM565 output and the comparator input? C10.1μ FSK Input w₁ R2 100k -o+5V(Vcc) VR1 10k C4 C5: 0.1 μ. 0.1μ 0.1 μ 8 10 R3 R4 D₁ FSK Phase Rx 7 10K 10K Detector www ww ww 1N4004 + Demodulated Output 6 AMP R₁ 6 100k 3 C₂ 0.05 μ VCO 4 5 9 U1 -5V LM565 -0-5V(VEE) Fig. 14-2 FSK demodulator U2 R6 μ4741 10k

Answer 1

Question

Chapter 8, Problem 8.29P

Interpretation Introduction

Interpretation:

The final properties of A 3105 aluminum plate which is reduced from 1.75 in to 1.15 in should be determined.

Concept Introduction:

At subzero temperature, the aluminium/ aluminum A 3105 alloy has higher strength. It also has high ductility. This alloy is made up of 98% of pure aluminum.

This alloy hasthe following properties:

Corrosion resistnce is high

Good in weldability

Good in formabilty
Density of the aluminimum alloy is 2.6-2.8 g/cm³ and the melting temperature is 641 °C.
Th aluminium alloys is made up of 99.0 % of Aluminium (Al), 0.55 % of Mangnese (Mn)

and 0.50 % of Magnesium(Mg)

Expert Solution & Answer

Trending nowThis is a popular solution!

See solution

Check out sample textbook solution

Students have asked these similar questions

3. What is the function of LM565 pin 6? 4. What is the purpose of the multistage low-pass filter between the LM565 output and the comparator input? C10.1μ FSK Input w₁ R2 100k -o+5V(Vcc) VR1 10k C4 C5: 0.1 μ. 0.1μ 0.1 μ 8 10 R3 R4 D₁ FSK Phase Rx 7 10K 10K Detector www ww ww 1N4004 + Demodulated Output 6 AMP R₁ 6 100k 3 C₂ 0.05 μ VCO 4 5 9 U1 -5V LM565 -0-5V(VEE) Fig. 14-2 FSK demodulator U2 R6 μ4741 10k

4.25 In this flow passage, the velocity is varying with time. The velocity varies with time at section A-A as 4m V-41/1-230/1 2.25- S to At time t = 0.50s, it is known that at section A-A the velocity gradient in the s direction is +2.1 m/s per meter. Given that to is 0.6 s and assuming quasi-1-D flow, answer the following questions for time t = 0.5 s: a. What is the local acceleration at A-A? b. What is the convective acceleration at A-A? A Diameter 50 cm Problem 4.25

1. What components determine the free-running frequency of the VCO in LM565 of Fig. 14-2? 2. What is the purpose of μA741 in Fig. 14-2? C10.1μ FSK Input -o+5V(Vcc) VR1 10k C4 C5: 0.1 μ. 0.1 μ 0.1 μ 8 10 R3 R4 R5 Phase Rx 7 10K 10K 10k D₁ FSK Detector www ww ww ww 1N4004 + Demodulated Output AMP 6 R₁ 6 100k w₁ R2 100k 3 C₂ 0.05 μ VCO 4 5 9 U1 -5V LM565 -0-5V(VEE) Fig. 14-2 FSK demodulator U2 R6 μ4741 10k