System Dynamics
3rd Edition
ISBN: 9780073398068
Author: III William J. Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 8.10P
The immersed object shown in Figure 8.1.2e is steel and has a mass of 100 kg and a specific heat of cp= 500 J/kg • °C. Assume the thermal resistance is R = 0.09°C • s/J. The inital temperature of the object is 20° when it is dropped into a large bath of temperature 80°C. Obtain the expression for the temperature 77/) of the object after it is dropped into the bath.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
5 Problem
=
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that
has properties similar to water with a density of ρ
1000 kg/m³ and thermal conductivity of
k = 0.606 Watts/(m.°C) and specific heat of c = 4182 J/(kg.° C). Suppose that an egg is fully
cooked when the temperature at the center reaches 70° C. Initially the egg is taken out of the
fridge at 4° C and placed in the boiling water at 100° C. Since the egg shell is very thin assume
that it quickly reaches a temperature of 100° C. The protein in the egg effectively immobilizes
the water so the heat conduction is purely conduction (no convection). Plot the temperature of
the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it
takes to cook the egg in minutes.
Figure 1: Image source: [Link]
Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintained at 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After 1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the other container. What is the temperature of the bar at the instant it is transferred?
An electric heater producing 260 W of heat is used to warm up a room containing 7 m3 of air. If we assume the room is perfectly sealed and there is no heat loss through the room boundaries, such that all of the heater output goes into increasing the air temperature, how long will it take to heat up the air in the room from 5.0 °C to 24.1 °C?
Give your answer to the nearest minute and assume that the specific volume (v = 0.85 m3/kg) and specific heat capacity at constant volume (cv = 1.005 kJ/(kg K)) remain constant throughout the heating process.
Chapter 8 Solutions
System Dynamics
Ch. 8 - Prob. 8.1PCh. 8 - Suppose the rocket motor in Problem 8.1 takes 0.04...Ch. 8 - Prob. 8.3PCh. 8 - Prob. 8.4PCh. 8 - Prob. 8.5PCh. 8 - Prob. 8.6PCh. 8 - Prob. 8.7PCh. 8 - Prob. 8.8PCh. 8 - The liquid-level system shown in Figure 8.1.2d has...Ch. 8 - The immersed object shown in Figure 8.1.2e is...
Ch. 8 - Prob. 8.11PCh. 8 - Prob. 8.12PCh. 8 - Prob. 8.13PCh. 8 - Prob. 8.14PCh. 8 - Prob. 8.15PCh. 8 - Prob. 8.16PCh. 8 - Prob. 8.17PCh. 8 - Obtain the response of the following models with...Ch. 8 - Prob. 8.19PCh. 8 - Prob. 8.20PCh. 8 - Prob. 8.21PCh. 8 - Prob. 8.22PCh. 8 - Prob. 8.23PCh. 8 - If applicable, compute <, r, a>„, and iod for the...Ch. 8 - Prob. 8.25PCh. 8 - Prob. 8.26PCh. 8 - 8.27 Given the model
,v — (/z + 2)i + (2/z + 5)x =...Ch. 8 - Prob. 8.28PCh. 8 - Prob. 8.29PCh. 8 - 8.30 The characteristic equation of a certain...Ch. 8 - Prob. 8.31PCh. 8 - Prob. 8.32PCh. 8 - Prob. 8.33PCh. 8 - Prob. 8.34PCh. 8 - Prob. 8.35PCh. 8 - Derive the fact that the peak time is the same for...Ch. 8 - Prob. 8.37PCh. 8 - Prob. 8.40PCh. 8 - Prob. 8.41PCh. 8 - Prob. 8.42PCh. 8 - Prob. 8.43PCh. 8 - Prob. 8.44PCh. 8 - Prob. 8.45P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Please include explanation andshow handwritten solutionarrow_forwardConsider an experimental structure required to always have constant pressure. For this purpose, a collapsible compartment has been installed that expands and contracts to adjust the volume of air inside the structure for maintaining constant air pressure of 1 atm. Given the total volume of air inside the structure was 100,000 m' when the compartment was fully collapsed, solve the following: If a constant pressure is to be maintained while the temperature varies from 0°F to 150°F, find the volume of air that the compartment holds when it expands to the maximum. For the temperature transition mentioned above, find the change in internal energy undergone by the air in the structure. Also, find the work done by the compartment while it expands. Assume air to be an ideal gas.arrow_forwardFind the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTUarrow_forward
- a) First, let's start with the steady-state analysis for the cable. What is the steady-state temperature of the wire surface if this current has been passing through the cable for a long period of time in these underwater conditions? Enter only a numeric value (with no units entered) and express your answer in ∘C. b) Now, let's think about the transient case. Assume that the cable starts at the same uniform temperature as the water and then the electrical current is passed through the cable. We're now interested in the amount of time it takes to heat up. Start by calculating the Biot number for this scenario. Enter only a numeric value (your answer should be unitless). c)arrow_forwardNote:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.arrow_forwardSolve it correctly please. I will rate accordingly with 3votes.arrow_forward
- In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the sun during the day. The tank wall thickness is 3cm containing molten salt at a temperature of 390 degree Celsius. There is atmospheric air outside the tank at a temperature of 30 degree Celsius. Suppose heat is lost as a result of heat transfer from the molten salt to the atmospheric air. What is the mode of heat transfer in this condition? conduction then convection convection then conduction convection then conduction then convection conduction then convection then conductionarrow_forward1arrow_forwardQ3. What is the analogical reason between heat transfer by conduction and flow of electricity through ohmic resistance? Use a composite wall of a building to illustrate the concept. A composite slab with three layers of thermal conductivities k1, k2, k3 and thickness t1, t2, t3 respectively, are placed in a close contact. Derive an expression from the first principle for the heat flow through the composite slab per unit surface area in terms of the overall temperature difference across the slab.arrow_forward
- 7. Determine the heat loss through a ventilated attic under the following conditions: indoor temperature 21°C, outdoor temperature 10°C, roof area 260 m', ceiling area 200 m', ceiling U-value = 0.15 W/m’K (include films), roof U-value = 1.7 W/m’K (include films), attic ventilation = 10 L/s. Neglect the air leakage through the ceiling. Determine the attic temperature.arrow_forwardIf you know that the internal energy value of an ideal gas rises by 3^10x3 Joules when the pressure is stabilized at 3^10x3 PA while the system gains a thermal energy of 3^ 10x4.2 joules. Calculate the change in system size 1:29 //arrow_forwardNeed correctly.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license