Elements of Electromagnetics
Elements of Electromagnetics
7th Edition
ISBN: 9780190698669
Author: Sadiku
Publisher: Oxford University Press
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 8, Problem 6P

(a)

To determine

Prove that the electron beam must be ejected out of the field in parallel path to the input beam as mentioned in the Figure given in the textbook.

(a)

Expert Solution
Check Mark

Explanation of Solution

Calculation:

Refer to the mentioned Figure given in the textbook.

Consider the general expression to calculate the force using Newton’s second law of motion.

F=ma=eu×B        (1)

Here,

m is the mass of the particle,

a is the acceleration,

u is the velocity, and

B is the electric field intensity.

Rewrite the equation (1) as follows,

mdudt=e|axayazuxuyuz00Bo|mddt(ux,uy,uz)=e[(Bouy)ax(Boux)ay+(0)az]mddt(ux,uy,uz)=e(Bouy,Boux,0)mddt(ux,uy,uz)=e(Bouy,Boux,0)

Reduce the equation as follows,

ddt(ux,uy,uz)=em(Bouy,Boux,0)        (2)

From equation (2), the velocities are,

duxdt=eBomuy

duxdt=ωuy{ω=eBom}        (3)

duydt=eBomux

duydt=ωux{ω=eBom}        (4)

duzdt=0uz=C=0        (5)

From equation (3),

d2uxdt2=ωduydtu¨x=ωu˙yu¨x=ω2ux{u˙y=ωux}u¨x+ω2ux=0

On solving the above expression,

ux=Acosωt+Bsinωt        (6)

From equation (3),

u˙x=ωuyuy=1ωu˙xuy=1ωddx(Acosωt+Bsinωt){ux=Acosωt+Bsinωt}uy=1ω(Aωsinωt+Bωcosωt)

Reduce the equation as follows,

uy=AsinωtBcosωt        (7)

Substitute 0 for t in equation (6) and (7).

ux=uo,uy=0A=uo,B=0

Therefore, equation (6) and (7) becomes,

ux=uocosωtdxdt=uocosωt{ux=dxdt}

x=uoωsinωt+c1        (8)

uy=uosinωtdydt=uosinωt

y=uoωcosωt+c2        (9)

At t=0, x=y=0c1=0,c2=uoω. Therefore, the equation (8) and (9) becomes,

x=uoωsinωt        (10)

y=uoωcosωt+uoω

y=uoω(1cosωt)        (11)

From equation (10) and (11),

(uoω)2(cos2ωt+sin2ωt)=(uoω)2=x2+(yuoω)2

From the above expression, the electron must move in a circle which is centered at (0,uoω) with radius uoω. In the referred Figure, the field does not exist throughout the circular region, therefore electron passes through a semi-circle and ejected out horizontally.

Conclusion:

Thus, the electron beam must be ejected out of the field in parallel path to the input beam is proved.

(b)

To determine

Find an expression for the exit distance (d) above the entry point as shown in the mentioned Figure given in the textbook.

(b)

Expert Solution
Check Mark

Answer to Problem 6P

The exit distance (d) above the entry point is 2uomeBo.

Explanation of Solution

Calculation:

Refer to the mentioned Figure given in the textbook. The distance d is twice the radius of the semi-circle. Therefore,

d=2uoω=2uo(eBom){ω=eBom}=2uomeBo

Conclusion:

Thus, the exit distance (d) above the entry point is 2uomeBo.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Qu. 5 Composite materials are becoming more widely used in aircraft industry due to their high strength, low weight and excellent corrosion resistant properties. As an engineer who is given task to design the I beam section of an aircraft (see Figure 7) please, answer the following questions given the material properties in Table 3. Determine the Moduli of Elasticity of Carbon/Epoxy, Aramid/Epoxy, and Boron /Epoxy composites in the longitudinal direction, given that the composites consist of 25 vol% epoxy and 75 vol% fiber. What are the specific moduli of each of these composites? What are the specific strengths (i.e. specific UTS) of each of these composites? What is the final cost of each of these composites?please show all work step by step problems make sure to see formula material science
Mueh Battery operated train Coll 160,000kg 0.0005 0.15 5m² 1.2kg/m³ CD Af Pair 19 пре neng 0.98 0.9 0.88 Tesla Prated Tesla Trated "wheel ng Joxle 270 kW 440NM 0,45m 20 8.5kg m2 the middle Consider a drive cycle of a 500km trip with 3 stops in Other than the acceleration and deceleration associated with the three stops, the tran maintains constat cruise speed velocity of 324 km/hr. The tran will fast charge at each stop for 15 min at a rate Peharge = 350 kW ΟΙ 15MIN Stop w charging (350kW) (ผม τ (AN GMIJ t 6M 1) HOW MUCH DISTANCE dace is covered DURING THE ACCELERATION TO 324 km/hr? 2) DETERMINE HOW LONG (IN seconds) the tran will BE TRAVELING AT FULL SPEED 2 ? 3) CALCULATE THE NET ENERGY GAW PER STOP ete
Please stop screenshoting ai solution,it always in accurate solve normal

Chapter 8 Solutions

Elements of Electromagnetics

Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Introduction to Kinematics; Author: LearnChemE;https://www.youtube.com/watch?v=bV0XPz-mg2s;License: Standard youtube license