Find the acceleration required to reach the speed of 10 mph from the rest position within the time period of 25 seconds. Calculate the total distance traveled by bicyclist and also calculate the average speed of cyclist during the first 25 s, 620 s, and 625 s.
Explanation of Solution
Calculate the acceleration required to reach the speed of 10 mph from the rest position within 25 s.
During the initial 25 seconds, the speed increases from 0 to 10 mph. Therefore, the average speed is
Calculate the distance traveled by the bicyclist with the average speed of 5 miles/h during the initial 25 s as follows.
Consider the constant average speed of 10 miles/h in the next 10 minutes.
Calculate the distance traveled by the bicyclist with the average speed of 10 miles/h during the next 10 minutes.
Here, the bicyclist decelerates at the constant rate from a speed of 10 mph to 0, the average speed of the bicyclist during the last 5 seconds is 5 mph.
Calculate the distance traveled during this period as below.
The total distance traveled is
Substitute 1833.33 ft for
Use the expression for the average speed of the bicyclist for the entire duration of travel.
Substitute 9020 feet for distance traveled and 625 s for time.
Conclusion:
Thus, the acceleration required to reach the speed of 10 mph in 25 s is
Want to see more full solutions like this?
Chapter 8 Solutions
EBK ENGINEERING FUNDAMENTALS: AN INTROD
- Find the collapse load (Wu) for the one-end continuous beam shown below. Use virtual work method Wu 6 marrow_forwardFind the maximum distributed load can be applied to the two fixed ends beam shown below. Use Virtual work method Wu L=6marrow_forwardCalculate the collapse load (P) for the two fixed ended beam shown below. Use virtual work method P 2 m 4 m L=6marrow_forward
- Question 1 (Approximate Method - Superposition). Using Superposition determine the displacement at C of this beam. El is constant. (Note - you must use the PE Handbook Shears, Moments and Deflection Tables. The FE handbook does not have one of these conditions) (On an exam I will make sure it is found in both the FE and the PE handbook). 60 kN 30 kN/m A C 3 m 3 m B Question 2 (Slope and Deflection - virtual work - statically determinate beam) Using virtual work determine the slope at A and the displacement at C of this beam. El is constant. Same beam as question #1arrow_forwardQuestion 4 (Force Method). Determine the reaction at the supports. Assume A is a pin and B and C are rollers. El is constant. 1.5 k A A 10 ft 10 ft B C - 20 ftarrow_forwardFind the maximum load (collapse load) that can be carried by the simply supported beam shown below. P ↓ 3 m 3 marrow_forward
- Find the maximum distributed load can be applied to the two fixed ends beam shown below. Wu L=6marrow_forwardIn excavation for a wall footing, the water table level was lowered from a depth of 1.0 m to a depth of 3.0 m in a clayey soil deposit. Considering that the soil has a water content of 28% when it is fully saturated, and above the water table the (dry) unit weight of the soil is 17 kN/m³. Assuming initially that all of the soil above the water table is dry, then compute the following: 1. The effective stress at a depth of 4.0 m after the lowering of the water table. Take Gs = 2.68. (Hints: w*Gs=Sr*e) 2. The increase in effective stress at a depth of 5 m. (You also need to plot the values of total vertical stress and effective vertical stress against depth before and after lowering the water table.)arrow_forwardCalculate the collapse load (P) for the two fixed ended beam shown below. P 2 m 4 m L=6marrow_forward
- The vertical stress at a point in soil is σx =400 kN/m², Txz = 50kN/m² while the horizontal stress at the same point is σ =100 kN/m², Tzx = -50kN/m². (a) Draw the Mohr circle that describes the 2D stress state at the point. (b) Find the maximum shear stress that acts at the point and its orientation angle from the horizontal plane. (c) Find the principal stress (σ₁ and σ3) that acts at the point and locate the major principal stress plane and its orientation angle from the horizontal plane (Use the pole method). (d) Determine both the normal and shear stress at a plane that orientates from the major principal stress plane with an angle of 30° (counterclockwise direction) and verify your results with the stress transformation equations.arrow_forward2: A billboard 2 m high x 4 m wide is supported on each end by a pin jointed assembly (bracing not shown for simplification). Total weight of billboard is 32 kN. Given: H = 1m; Angle φ = 60⁰; q = 2.4 kPa.1. Determine the normal stress (MPa) in strut AB with crosssectional dimension 6 mm x 50 mm.2. Determine the normal stress (MPa) in strut BC with crosssectional dimension 8 mm x 40 mm.3. Determine the required diameter (mm) of pin (under double shear) to be used in A or C if the allowable shear stress of the pin is 120 MPa.arrow_forwardA total load of 900 kN is uniformly distributed over a rectangular footing of size 2 mx3 m. Find the vertical stress at a depth of 1.0 m below the footing at point C, under one corner, and D, under the center. If another footing of size 1 m × 3 m with a total load of 450 kN is constructed adjoining the previous footing, what is the vertical stress at the corner point E at the same depth due to the construction of these two footings. k 3 m 1m 2m E 3 marrow_forward
- Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage LearningEngineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
- Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage LearningSolid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781285852225Author:Gregory W FletcherPublisher:Cengage Learning