Find the power radiated by a woodstove.
Answer to Problem 1P
The power radiated by a woodstove is
Given information:
The size of the woodstove is
The surface temperature (T) is
The emissivity
Calculation:
Find the surface area of the woodstove.
Convert the surface temperature from Degree Celsius to Kelvin:
Consider the Stephen Boltzmann constant
Find the surface radiation (P):
Thus, the power radiated by a woodstove is
Explanation of Solution
Given information:
The size of the woodstove is
The surface temperature (T) is
The emissivity
Calculation:
Find the surface area of the woodstove.
Convert the surface temperature from Degree Celsius to Kelvin:
Consider the Stephen Boltzmann constant
Find the surface radiation (P):
Thus, the power radiated by a woodstove is
Want to see more full solutions like this?
- A 50-L electrical radiator containing heating oil is placed in a 50-m³ room. Both the room and the oil in the radiator are initially at 5°C. The radiator with a rating of 3 kW is now turned on. At the same time, heat is lost from the room at an average rate of 0.3 kJ/s. After some time, the average temperature is measured to be 20°C for the air in the room, and 60°C for the oil in the radiator. Taking the density and the specific heat of the oil to be 950kg/m³ and 2.2kJ/(kg °C), respectively, determine how long the heater is kept on. Assume the room is well-sealed so that there are no air leaks.arrow_forwardA certain parallel-plate capacitor is filled with a dielectric for which K = 6.50. The area of each plate is 0.0524 m², and the plates are separated by 2.97 mm. The capacitor will fail (short out and burn up) if the electric field between the plates exceeds 179 KN/C. What is the maximum energy that can be stored in the capacitor? Number i ! Units Jarrow_forwardCalculate the change in a 5-m long copper wire when its temperature changes by 120 oF. Thecoefficient of thermal expansion for copper is approximately 17 x 10-61/oC. Express your answerin SI units.arrow_forward
- choose the correct answerarrow_forwardA closed tank containing hot air has an initial internal energy of 400 kJ. During the next 5 min, the tank loses heat to the surroundings at a rate of 1.5 kW, while an electrical element supplies 1000 W to the air. Find the final internal energy of the air.arrow_forwardA nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle, the specific enthalpy of the fluid is 3320 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the specific enthalpy is 2530 kJ/kg. The nozzle is horizontal, and the heat supply, the heat loss, the work input, and the work output to or from the nozzle are all negligible. (a) Determine the velocity at the nozzle exitarrow_forward
- A line was measured to be 412 m using a 30-m tape, which is of standard length at a temperature of 20 deg.C. During measurement, the temperature was 52 deg.C. If the coefficient of thermal expansion of the tape material is 0.0000116 m/m deg.C, calculate the correct length of the line.arrow_forwardOne of the most common appliances used on a daily basis is the hair dryer. A hair dryer is basically a duct in which a few layers of electric resistors are placed. A small fan at the back of the device pulls the air in and forces it through the resistors where it is heated (see Fig. 1). The power consumed by the heating elements (i.e. electric resistors) of the hair dryer is 1258 Watts. Air enters the hair dryer at 95 kPa and 25°C and leaves at 50°C. The cross-sectional area of the hair dryer at the exit is 55 cm². The power consumed by the fan is 2 Watts and the heat loss through the walls of the hair dryer is 5 Watts. By clearly stating your assumptions throughout, 1.Analytically describe the Fluid Mechanics and Thermodynamics working principles of the hairdryer; 2. Provide a schematic diagram of the hair dryer clearly indicating the system's boundaries, mass flows and energy/heat flows; 3. Determine the volumetric flow rate of the air at the inlet; 4. Determine the velocity of the…arrow_forwardDetermine the luminous efficacy of the following lamps having comparable illumination outputs:a. A 300 W incandescent lamp that emits 5820 lmb. Two 32 W linear fluorescent lamps that emit 2950 lm per lamp in a luminaire that consumes 70 W including the ballastsc. A 70 W metal halide lamp that consumes 88 W, including the ballast and emits 5500 lmarrow_forward
- An electric baseboard heater has 25 ohms of resistance. The heater uses 9.6amperes of current. Find in volts the voltage required for the heater.arrow_forwardA dual-pane window in a house is composed of two parallel panes of glass, each with an area of 2.23 m². Each pane of glass is 3.10 mm thick and the space between the panes is 12.5 mm thick and is filled with argon. (a) Calculate the heat flow through the window if the indoor temperature is 18.3°C and the outdoor temperature is -20.6°C (this is about -5°F). (b) Determine the temperature on the inside of the pane (this is in the argon-dilled region) closest to the outside of the house.arrow_forwardA glass flask whose volume is 1000.00 cm³ at 0.0°C is completely filled with mercury at this temperature. When flask and mercury are warmed to 56.5° C, 8.90 cm³ of mercury overflow. Part A If the coefficient of volume expansion of mercury is 18.0 × 10-5 K-1, compute the coefficient of volume expansion of the glass. Express your answer in inverse Celsius degrees. ΑΣΦ Bglass = Submit Request Answer ? (C")-1arrow_forward
- Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning