Find the speed’s magnitude of the person at equator due to earth’s rotational speed.

Question

1. Calculate the ultimate load carrying capacity of the pile tip driven into the soil profile shown below: G.W.T. 45' Qapp Soft Clay: Ysat 100 pcf Cu 500 psf, ou = 0° 平 12' Soil Plug Driven Steel Pipe Pile: Outside Diameter = 2' Inside Diameter = 1'11" Hollow (soil plugged) Note: Pile & soil profile are not drawn to scale Qp = ? Please perform the tip capacity calculation two ways: For the first approach, assume that the total vertical stress at the pile tip is balanced by the weight of the pile. For the second approach, assume that the total vertical stress at the pile tip is not balanced by the weight of the pile (which means you need to include the vertical total stress term). Please compare your answers from these two analyses, examine some of your intermediate-stage calculation results such as the total overburden stress at the pile tip relative to the weight of the pile, and discuss whether or not the commonly used assumption about the total vertical stress at the pile tip is a…

Answer 1

Question

100%

Chapter 8, Problem 15P

To determine

Find the speed’s magnitude of the person at equator due to earth’s rotational speed.

Expert Solution & Answer

Trending nowThis is a popular solution!

See solution

Check out sample textbook solution

Students have asked these similar questions

1. Calculate the ultimate load carrying capacity of the pile tip driven into the soil profile shown below: G.W.T. 45' Qapp Soft Clay: Ysat 100 pcf Cu 500 psf, ou = 0° 平 12' Soil Plug Driven Steel Pipe Pile: Outside Diameter = 2' Inside Diameter = 1'11" Hollow (soil plugged) Note: Pile & soil profile are not drawn to scale Qp = ? Please perform the tip capacity calculation two ways: For the first approach, assume that the total vertical stress at the pile tip is balanced by the weight of the pile. For the second approach, assume that the total vertical stress at the pile tip is not balanced by the weight of the pile (which means you need to include the vertical total stress term). Please compare your answers from these two analyses, examine some of your intermediate-stage calculation results such as the total overburden stress at the pile tip relative to the weight of the pile, and discuss whether or not the commonly used assumption about the total vertical stress at the pile tip is a…

A6.2- Given a simply supported beam with the typical cross-section as shown in the figure below. Assume interior exposure for this beam. The beam properties are summarized below. a) Check if the beam section satisfies the CSA A23.3 cracking control requirements. In your calculations, find f, accurately based on the loading, and compare the results with f = 0.6 fy. b) Find the deflection due to DL+LL at mid-span after 6 years. Given: Concrete: Normal density with f'c = 25 MPa Reinforcement: Uncoated rebars with fy = 400 MPa Shear reinforcement: 10M Maximum aggregate size: 20 mm Clear cover to the stirrup: 30 mm Clear spacing between the bars = 35 mm 35 mm 30 mm m WDL= 20 kN/m WLL= 15 kN/m 抖抖 b=400 mm As = 8-25M Cross-section h=500 mm

A5.1- An unbraced column shown in Figure 1, column A-B with square cross-section is given. The column is subjected to Dead load (unfactored): PDL = 3000 kN, MDL-top = 85 kN.m, MDL-bo = -DL-bottom = 100 kN.m. = Assume the cross-section of column is constant from top to bottom, and all the beams have width = 300 mm and height 350 mm. Using f'c = 25 MPa, fy = 400 MPa, design the column and determine the ties spacing and arrangement. Use 25M or 30M bars for longitudinal reinforcement, and 10M bars for ties. Assume clear cover to be 40mm. The design p has to be between 0.01 and 0.02. Column maximum dimension can be 500mm. т 4.0m 7.0m 5.5m + 6.5m Figure 1 B