Precision Machining Technology (MindTap Course List)
2nd Edition
ISBN: 9781285444543
Author: Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7.3, Problem 1RQ
List five surface grinder safety guidelines.
Expert Solution & Answer
To determine
Five surface grinder safety guidelines.
Explanation of Solution
The five safety guidelines that should be observed while grinding are as follow.
- Always wear safety glasses.
- Check that all the machine’s guards and covers are in place before starting any operation.
- Never use a grinder that is locked out or tagged out.
- Always shut off the wheel and allow it to stop completely before adjusting or measuring the work-piece.
- Do not force the wheel into the work. It may result into failure of work-holding devices or breaking of grinding wheels.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Thermodynamics: Mass and Energy Analysis Of Control Volumes
A spring-loaded piston-cylinder device contains 1.5 kg of carbon dioxide. This system is heated from 200kPa and 25◦C to 1200 kPa and 300◦C. Determine the total heat transfer to and work produced by this system.
Can you help with a code in MATLAB?
I need help writing a code in MATLAB. Please help me with question b.6
Chapter 7 Solutions
Precision Machining Technology (MindTap Course List)
Ch. 7.1 - What are three benefits of precision grinding?Ch. 7.1 - What is the major use of the surface grinder?Ch. 7.1 - What are the two spindle types used for surface...Ch. 7.1 - What are the two types of table movements used for...Ch. 7.1 - Label the parts of the surface grinder.Ch. 7.1 - What are three types of cylindrical grinders?Ch. 7.1 - Tool and cutter grinders can be used to _______...Ch. 7.2 - What wheel shapes are commonly used for surface...Ch. 7.2 - What abrasive is commonly used to grind steels?Ch. 7.2 - What abrasive is used to grind nonferrous metals,...
Ch. 7.2 - What does CBN stand for?Ch. 7.2 - What superabrasive is a good choice for grinding...Ch. 7.2 - The grade of a wheel describes its __________ on a...Ch. 7.2 - Prob. 7RQCh. 7.2 - Prob. 8RQCh. 7.2 - Generally, harder wheels should be used to grind...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V What is the...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V What type of...Ch. 7.3 - List five surface grinder safety guidelines.Ch. 7.3 - What should be done to every grinding wheel before...Ch. 7.3 - When using a magnetic workholding device, the work...Ch. 7.3 - When using a magnetic chuck to hold a workpiece...Ch. 7.3 - Describe the difference between wheel truing and...Ch. 7.3 - What tool is used to true and dress an aluminum...Ch. 7.3 - How is a CBN wheel trued and dressed?Ch. 7.3 - Depth-of-cut range for surface grinding is: a....Ch. 7.3 - What should be done to a magnetic chuck when it...Ch. 7.3 - What workholding device can extend the magnetic...Ch. 7.3 - What workholding device can be used when grinding...Ch. 7.3 - Briefly describe the method for grinding two...Ch. 7.3 - List three types of workpiece features that can be...Ch. 7.3 - List three possible solutions to eliminate bum...Ch. 7.3 - What can cause scratches on the surface of a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Thermodynamics: Mass and Energy Analysis Of Control Volumes 1.5-kg of water that is initially at 90◦C with a quality of 5 percent occupies a spring-loaded piston-cylinder device. This device is now heated until the pressure rises to 900 kPa and the temperature is 280◦C. Determinethe total work produced during this process, in kJ.arrow_forwardThermodynamics: Mass and Energy Analysis Of Control Volumes Stainless steel ball bearings (ρ = 8085 kg/m3 and cp = 0.480 kJ/(kg◦C)) having a diameter of 1.5 cm areto be quenched in water at a rate of 900 per minute. The balls leave the oven at a uniform temperature of1000◦C and are exposed to air at 25◦C for a while before they are dropped into the water. If the temperatureof the balls drops to 900◦C prior to quenching, determine the rate of heat transfer from the balls to the air.arrow_forwardThermodynamics: Mass and Energy Analysis Of Control Volumes A 12-ft3 tank contains oxygen at 15 psia and 80◦F. A paddle wheel within the tank is rotated until thepressure inside rises to 20 psia. During the process 25 Btu of heat is lost to the surroundings. Determine thepaddle wheel work done. Neglect the energy stored in the paddle wheel.arrow_forward
- Thermodynamics: Mass and Energy Analysis Of Control Volumes A frictionless piston-cylinder device contains 4.5 kg of nitrogen at 110 kPa and 200 K. Nitrogen is nowcompressed slowly according to the relation PV1.5 = constant until it reaches a final temperature of 360 K.Calculate the work input during the process, in kJ.arrow_forwardThermodynamics: Mass and Energy Analysis Of Control Volumes An insulated piston-cylinder device contains 4 L of saturated liquid water at a constant pressure of 200 kPa.Water is stirred by a paddle wheel while a current of 8 A flows for 50 min through a resistor placed in thewater. If one-half of the liquid is evaporated during this constant-pressure process and the paddle-wheelwork amounts to 300 kJ, determine the voltage of the source. Also, show the process on a P–v diagram withrespect to the saturation lines.arrow_forwardThermodynamics: Mass and Energy Analysis Of Control Volumes The state of liquid water is changed from 55 psia and 45◦F to 2000 psia and 120◦F. Determine the change inthe internal energy and enthalpy of water on the basis of the (a) compressed liquid tables, (b) incompressiblesubstance approximation and property tables, and (c) specific-heat model.arrow_forward
- Thermodynamics: Mass and Energy Analysis Of Control Volumes What is the change in enthalpy, in kJ/kg, of oxygen as its temperature changes from 150 to 250◦C? Is thereany difference if the temperature change were from −50 to 100◦C? Does the pressure at the beginning andend of this process have any effect on the enthalpy change?arrow_forwardThermodynamics: Mass and Energy Analysis Of Control Volumes A 50-L electrical radiator containing heating oil is placed in a 50-m3 room. Both the room and the oil in theradiator are initially at 5◦C. The radiator with a rating of 3 kW is now turned on. At the same time, heatis lost from the room at an average rate of 0.3 kJ/s. After some time, the average temperature is measuredto be 20◦C for the air in the room, and 60◦C for the oil in the radiator. Taking the density and the specificheat of the oil to be 950 kg/m3 and 2.2 kJ/(kg◦C), respectively, determine how long the heater is kept on.Assume the room is well-sealed so that there are no air leaks.arrow_forwardProblem 3 For the beam and loading shown, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point a. 1ft 15 kips 20 kips 15 kips AITT in 1 0.6 in. -10 in. 1 in. 0.375 in.- 2 ft 2ft 2 ft 2ft 10 in. 1 0.6 in.arrow_forward
- practice problems want detailed break downarrow_forward6.105. Determine force P on the cable if the spring is compressed 0.025 m when the mechanism is in the position shown. The spring has a stiffness of k = 6 kN/m. E P 150 mm D T 30° 200 mm 200 mm 200 mm B 800 mmarrow_forward6.71. Determine the reactions at the supports A, C, and E of the compound beam. 3 kN/m 12 kN A B CD E -3 m 4 m 6 m 3 m 2 marrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License