
Precision Machining Technology (MindTap Course List)
2nd Edition
ISBN: 9781285444543
Author: Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 7.3, Problem 1RQ
List five surface grinder safety guidelines.
Expert Solution & Answer

To determine
Five surface grinder safety guidelines.
Explanation of Solution
The five safety guidelines that should be observed while grinding are as follow.
- Always wear safety glasses.
- Check that all the machine’s guards and covers are in place before starting any operation.
- Never use a grinder that is locked out or tagged out.
- Always shut off the wheel and allow it to stop completely before adjusting or measuring the work-piece.
- Do not force the wheel into the work. It may result into failure of work-holding devices or breaking of grinding wheels.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Auto Controls
Using MATLAB , find the magnitude and phase plot of the compensators
NO COPIED SOLUTIONS
4-81 The corner shown in Figure P4-81 is initially uniform at 300°C and then suddenly
exposed to a convection environment at 50°C with h 60 W/m². °C. Assume the
=
2
solid has the properties of fireclay brick. Examine nodes 1, 2, 3, 4, and 5 and deter-
mine the maximum time increment which may be used for a transient numerical
calculation.
Figure P4-81
1
2
3
4
1 cm
5
6
1 cm
2 cm
h, T
+
2 cm
Auto Controls
A union feedback control system has the following open loop transfer function
where k>0 is a variable proportional gain
i. for K = 1 , derive the exact magnitude and phase expressions of G(jw).
ii) for K = 1 , identify the gaincross-over frequency (Wgc) [where IG(jo))| 1] and phase cross-overfrequency [where <G(jw) = - 180]. You can use MATLAB command "margin" to obtain there quantities.
iii) Calculate gain margin (in dB) and phase margin (in degrees) ·State whether the closed-loop is stable for K = 1 and briefly justify your answer based on the margin . (Gain marginPhase margin)
iv. what happens to the gain margin and Phase margin when you increase the value of K?you
You can use for loop in MATLAB to check that.Helpful matlab commands : if, bode, margin, rlocus
NO COPIED SOLUTIONS
Chapter 7 Solutions
Precision Machining Technology (MindTap Course List)
Ch. 7.1 - What are three benefits of precision grinding?Ch. 7.1 - What is the major use of the surface grinder?Ch. 7.1 - What are the two spindle types used for surface...Ch. 7.1 - What are the two types of table movements used for...Ch. 7.1 - Label the parts of the surface grinder.Ch. 7.1 - What are three types of cylindrical grinders?Ch. 7.1 - Tool and cutter grinders can be used to _______...Ch. 7.2 - What wheel shapes are commonly used for surface...Ch. 7.2 - What abrasive is commonly used to grind steels?Ch. 7.2 - What abrasive is used to grind nonferrous metals,...
Ch. 7.2 - What does CBN stand for?Ch. 7.2 - What superabrasive is a good choice for grinding...Ch. 7.2 - The grade of a wheel describes its __________ on a...Ch. 7.2 - Prob. 7RQCh. 7.2 - Prob. 8RQCh. 7.2 - Generally, harder wheels should be used to grind...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V What is the...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V Which wheel...Ch. 7.2 - Wheel A: 32A60H8V Wheel B: 39C100L6V What type of...Ch. 7.3 - List five surface grinder safety guidelines.Ch. 7.3 - What should be done to every grinding wheel before...Ch. 7.3 - When using a magnetic workholding device, the work...Ch. 7.3 - When using a magnetic chuck to hold a workpiece...Ch. 7.3 - Describe the difference between wheel truing and...Ch. 7.3 - What tool is used to true and dress an aluminum...Ch. 7.3 - How is a CBN wheel trued and dressed?Ch. 7.3 - Depth-of-cut range for surface grinding is: a....Ch. 7.3 - What should be done to a magnetic chuck when it...Ch. 7.3 - What workholding device can extend the magnetic...Ch. 7.3 - What workholding device can be used when grinding...Ch. 7.3 - Briefly describe the method for grinding two...Ch. 7.3 - List three types of workpiece features that can be...Ch. 7.3 - List three possible solutions to eliminate bum...Ch. 7.3 - What can cause scratches on the surface of a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Auto Controls Hand sketch the root Focus of the following transfer function How many asymptotes are there ?what are the angles of the asymptotes?Does the system remain stable for all values of K NO COPIED SOLUTIONSarrow_forward-400" 150" in Datum 80" 90" -280"arrow_forwardUsing hand drawing both of themarrow_forward
- A 10-kg box is pulled along P,Na rough surface by a force P, as shown in thefigure. The pulling force linearly increaseswith time, while the particle is motionless att = 0s untilit reaches a maximum force of100 Nattimet = 4s. If the ground has staticand kinetic friction coefficients of u, = 0.6 andHU, = 0.4 respectively, determine the velocityof the A 1 0 - kg box is pulled along P , N a rough surface by a force P , as shown in the figure. The pulling force linearly increases with time, while the particle is motionless at t = 0 s untilit reaches a maximum force of 1 0 0 Nattimet = 4 s . If the ground has static and kinetic friction coefficients of u , = 0 . 6 and HU , = 0 . 4 respectively, determine the velocity of the particle att = 4 s .arrow_forwardCalculate the speed of the driven member with the following conditions: Diameter of the motor pulley: 4 in Diameter of the driven pulley: 12 in Speed of the motor pulley: 1800 rpmarrow_forward4. In the figure, shaft A made of AISI 1010 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite Forces F via shaft B. Stress concentration factors K₁ (1.7) and Kts (1.6) are induced by the 3mm fillet. Notch sensitivities are q₁=0.9 and qts=1. The length of shaft A from the fixed support to the connection at shaft B is 1m. The load F cycles from 0.5 to 2kN and a static load P is 100N. For shaft A, find the factor of safety (for infinite life) using the modified Goodman fatigue failure criterion. 3 mm fillet Shaft A 20 mm 25 mm Shaft B 25 mmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning

Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning

Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning

Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License