EBK PHYSICS FOR SCIENTISTS AND ENGINEER
EBK PHYSICS FOR SCIENTISTS AND ENGINEER
9th Edition
ISBN: 8220100663987
Author: Jewett
Publisher: Cengage Learning US
bartleby

Videos

Textbook Question
Book Icon
Chapter 7, Problem 7.57AP

Two identical steel balls, each of diameter 25.4 nun and moving in opposite directions at 5 m/s, run into each other head-on and bounce apart. Prior to the collision, one of the balls is squeezed in a vise while precise measurements are made of the resulting amount of compression. The results show that Hooke’s law is a fair model of the ball’s elastic behavior. For one datum, a force of 16 kN exerted by each jaw of the vise results in a 0.2-mm reduction in the diameter. The diameter returns to its original value when the force is removed, (a) Modeling the ball as a spring, find its spring constant. (b) Does the interaction of the balls during the collision last only for an instant or for a nonzero time interval? State your evidence, (c) Compute an estimate for the kinetic energy of each of the balls before they collide, (d) Compute an estimate for the maximum amount of compression each ball undergoes when the balls collide, (e) Compute an order-of-magnitude estimate for the time interval for which the balls are in contact. (In Chapter 15, you will learn to calculate the contact time interval precisely.)

(a)

Expert Solution
Check Mark
To determine

The spring constant of ball when models the ball as a spring.

Answer to Problem 7.57AP

The spring constant of ball is 8×107N/m .

Explanation of Solution

Given info: The diameter of each steel ball is 25.4mm , the speed of balls is 5m/s , the force exert by each jaw is 16kN and the compression of the steel along diameter is 0.2mm .

The ball models as a spring then from Hooke’s law, the force exerts on the spring is,

F=kx

Here,

k is the spring constant of steel ball.

x is the length of spring.

Rearrange the above equation.

k=Fx

Substitute 0.2mm for x and 16kN for F in the above equation.

k=16×103N0.2×103m=8×107N/m

Conclusion:

Therefore, the spring constant of ball is 8×107N/m .

(b)

Expert Solution
Check Mark
To determine

The interaction of the balls during the collision.

Answer to Problem 7.57AP

The interaction of the balls during the collision cannot happen.

Explanation of Solution

The interaction of the balls during the collision is calculable through the time period.

From the Newton’s law, the force exerts by a jaw is,

F=ma (1)

Here,

m is the mass of the steel ball.

a is the acceleration of the steel balls.

The expression for the acceleration of the steel balls is,

a=vt (2)

Here,

v is the speed of the ball.

t is the time interval during the collision.

The total velocity of the balls during the collision is,

v=vfvi

Here,

vf is the final speed of the steel ball.

vi is the initial speed of the steel ball.

Substitute vfvi for v in equation (2).

a=vfvit

Substitute vfvit for a in equation (1).

F=m(vfvit)

The interaction of the balls during the collision lasts for a time interval if the interaction takes no time interval that means t=0 .

Substitute 0 for t in the above equation.

F=m(vfvi0)

The zero time interval of interaction, the force exerted by each ball on the other would be infinite and that cannot happen.

Conclusion:

Therefore, the interaction of the balls during the collision cannot happen.

(c)

Expert Solution
Check Mark
To determine

The kinetic energy of each of the balls before they collide.

Answer to Problem 7.57AP

The kinetic energy of each ball is 0.8J .

Explanation of Solution

The value of density of the steel is 7860kg/m3 .

The expression for the volume of steel ball is,

V=43πr3 (3)

Here,

r is the radius of ball.

The radius of ball is the half of its diameter so the radius of steel ball is,

r=d2

Here,

d is the diameter of steel ball.

Substitute 25.4mm for d in the above equation.

r=25.4×103m2=0.0127m

Substitute 0.0127m for r in equation (3).

V=43π(0.0127m)38.580×106m3

The expression for the mass of the steel ball is,

m=ρV

Substitute 7860kg/m3 for ρ and 8.580×106m3 for V in the above equation.

m=(7860kg/m3)(8.580×106m3)0.0674kg

The expression for the kinetic energy of the steel ball before they collide is,

K=12mv2

Substitute 0.0674kg for m and 5m/s for v in the above equation.

K=12(0.0674kg)(5m/s)20.84300J0.8J

Conclusion:

Therefore, the kinetic energy of each ball is 0.8J .

(d)

Expert Solution
Check Mark
To determine

The maximum amount of compression each balls when balls collide.

Answer to Problem 7.57AP

The maximum amount of compression of each balls is 0.15mm .

Explanation of Solution

From part (c), the kinetic energy before collision of balls is,

K=0.8J

The expression for the kinetic energy of spring after the collision of balls is,

K=12kxmax2

Here,

xmax is the maximum compression in length of spring.

The ball is models as a spring so the kinetic energy before the collisions of balls is converted into spring energy.

From part (a), the spring constant of balls that models as a spring is,

k=8×107N/m

Substitute 0.8J for K and 8×107N/m for k in the above equation.

0.8J=12(8×107N/m)xmax2xmax=2(0.8J)8×107N/m0.1414×103m0.15mm

Conclusion:

Therefore, the maximum amount of compression of each balls is 0.15mm .

(e)

Expert Solution
Check Mark
To determine

The time interval for which the balls are in contact.

Answer to Problem 7.57AP

The time interval is 104s .

Explanation of Solution

From part (a), the force exerts on the both the balls that models as spring is,

F=kx

The average force of both the balls is,

F=kx+kx2=12(kx)

From part (b), the expression for the time interval is,

t=m(vfvi)F

Substitute 12(kx) for F in the above equation.

t=m(vfvi)12(kx) (4)

The steel balls move in opposite direction of each other so the velocity has opposite sign after they bounce apart to each other.

From part (a), the spring constant of balls that models as a spring is,

k=8×107N/m

From part (c), the mass of steel ball is,

m=0.0674kg

From part (d), the spring constant of the ball is,

x=0.15mm

Substitute 0.0674kg for m and 5m/s for vf , 5m/s for vi , 0.15mm for x and 8×107N/m for k in equation (4).

t=2(0.0674kg)(5m/s(5m/s))(8×107N/m)(0.15×103m)1.0×104s104s

Conclusion:

Therefore, the time interval is 104s .

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Two people want to do a physics experiment at the bowling alley. They set up sensors to measure velocities and then roll two bowling balls with different masses so that they hit head on and collide elastically. The table summarizes the values known for the collision. Given the information, what is the mass of ball 2?   Ball 1 Ball 2 mass (kg) 5.05.0 ?? initial velocity (m/s) 7.07.0 −3.0−3.0 final velocity (m/s) −7.74−7.74 2.262.26
A car of mass 1,829 kg collides with a wall. The initial speed of the car is 15.1 m/s. After collision, the car bounced in the opposite direction at a speed of 2.9 m/s. If the collision lasted for 196 ms, what was the average force in newtons exerted on the car by the wall? Express your answer in two decimal places with units of Newton.
Two blocks (m₁ and m2) are released from rest at a height of h= 14.00 m on a rough track. The friction force 2.6 N acts on distance of 2.59 m along the track. The two objects meet on the horizontal section of the track where they undergo an elastic collision. If m1 = 4.09 kg and m2 = 7.93 kg, determine the velocity (in m/s) of object 2 before collision.

Chapter 7 Solutions

EBK PHYSICS FOR SCIENTISTS AND ENGINEER

Ch. 7 - A worker pushes a wheelbarrow with a horizontal...Ch. 7 - A cart is set rolling across a level table, at the...Ch. 7 - Prob. 7.5OQCh. 7 - Is the work required to be done by an external...Ch. 7 - A bloc k, of mass m is dropped from the fourth...Ch. 7 - An a simple pendulum swings back and forth, the...Ch. 7 - Bullet 2 has twice the mass of bullet 1. Both are...Ch. 7 - Figure OQ7.10 shows a light extended spring...Ch. 7 - If the speed of a particle is doubled, what...Ch. 7 - Prob. 7.12OQCh. 7 - Prob. 7.13OQCh. 7 - A certain spring that obeys Hookes law is...Ch. 7 - A cart is set rolling across a level table, al the...Ch. 7 - An ice cube has been given a push and slides...Ch. 7 - Can a normal force do work? If not, why not? If...Ch. 7 - Object 1 pushes on object 2 as the objects move...Ch. 7 - A student has the idea that the total work done on...Ch. 7 - (a) For what values of the angle between two...Ch. 7 - Prob. 7.5CQCh. 7 - Discuss the work done by a pitcher throwing a...Ch. 7 - Prob. 7.7CQCh. 7 - If only one external force acts on a particle,...Ch. 7 - Prob. 7.9CQCh. 7 - Prob. 7.10CQCh. 7 - A certain uniform spring has spring constant k....Ch. 7 - Prob. 7.12CQCh. 7 - Does the kinetic energy of an object depend on the...Ch. 7 - Cite two examples in which a force is exerted on...Ch. 7 - A shopper in a supermarket pushes a cart with a...Ch. 7 - A raindrop of mass 3.35 10-5 kg falls vertically...Ch. 7 - In 1990, Walter Arfeuille of Belgium lifted a...Ch. 7 - The record number of boat lifts, including the...Ch. 7 - A block of mass m = 2.50 kg is pushed a distance d...Ch. 7 - Spiderman, whose mass is 80.0 kg, is dangling on...Ch. 7 - Prob. 7.7PCh. 7 - Vector A has a magnitude of 5.00 units, and vector...Ch. 7 - Prob. 7.9PCh. 7 - Find the scalar product of the vectors in Figure...Ch. 7 - A force F = (6i 2j) N acts on a panicle that...Ch. 7 - Using the definition of the scalar product, find...Ch. 7 - Lei B = 5.00 m at 60.0. Let the vector C have the...Ch. 7 - The force acting on a panicle varies as shown in...Ch. 7 - A particle is subject to a force Fx that varies...Ch. 7 - In a control system, an accelerometer consists of...Ch. 7 - When a 4.00-kg object is hung vertically on a...Ch. 7 - Hookes law describes a certain light spring of...Ch. 7 - An archer pulls her bowstring back 0.400 m by...Ch. 7 - A light spring with spring constant 1 200 N/m is...Ch. 7 - A light spring with spring constant k1 is hung...Ch. 7 - Express the units of the force constant of a...Ch. 7 - A cafeteria tray dispenser supports a stack of...Ch. 7 - A light spring with force constant 3.85 N/m is...Ch. 7 - A small particle of mass m is pulled to the top of...Ch. 7 - The force acting on a particle is Fx = (8x 16),...Ch. 7 - When different loads hang on a spring, the spring...Ch. 7 - A 100-g bullet is fired from a rifle having a...Ch. 7 - A force F = (4xi + 3yj), where F is in newtons and...Ch. 7 - Review. The graph in Figure P7.20 specifies a...Ch. 7 - A 3.00-kg object has a velocity (6.00i - 2.00j)...Ch. 7 - Prob. 7.32PCh. 7 - A 0.600-kg particle has a speed of 2.00 m/s at...Ch. 7 - A 4.00-kg particle is subject to a net force that...Ch. 7 - A 2 100-kg pile driver is used to drive a steel...Ch. 7 - Review. In an electron microscope, there is an...Ch. 7 - Review. You can think of the workkinetic energy...Ch. 7 - Review. A 7.80-g bullet moving at 575 m/s strikes...Ch. 7 - Review. A 5.75-kg object passes through the origin...Ch. 7 - A 1 000-kg roller coaster car is initially at the...Ch. 7 - A 0.20-kg stone is held 1.3 m above the top edge...Ch. 7 - A 400-N child is in a swing that is attached to a...Ch. 7 - A 4.00-kg particle moves from the origin to...Ch. 7 - (a) Suppose a constant force acts on an object....Ch. 7 - A force acting on a particle moving in the xy...Ch. 7 - An object moves in the xy plane 111 Figure P7.43...Ch. 7 - Prob. 7.47PCh. 7 - Why is the following situation impossible? A...Ch. 7 - A potential energy function for a system in which...Ch. 7 - A single conservative force acting on a particle...Ch. 7 - A single conservative force acts on a 5.0-kg...Ch. 7 - For the potential energy curve shown in Figure...Ch. 7 - A right circular cone can theoretically be...Ch. 7 - The potential energy function for a system of...Ch. 7 - Prob. 7.55APCh. 7 - A particle moves along the xaxis from x = 12.8 m...Ch. 7 - Two identical steel balls, each of diameter 25.4...Ch. 7 - When an object is displaced by an amount x from...Ch. 7 - A 6 000-kg freight car rolls along rails with...Ch. 7 - Why is the following situation impossible? In a...Ch. 7 - Prob. 7.61APCh. 7 - The spring constant of an automotive suspension...Ch. 7 - An inclined plane of angle = 20.0 has a spring of...Ch. 7 - An inclined plane of angle has a spring of force...Ch. 7 - (a) Take U = 5 for a system with a particle at...Ch. 7 - A particle of mass m = 1.18 kg is attached between...Ch. 7 - Review. A light spring has unstressed length 15.5...
Knowledge Booster
Background pattern image
Physics
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Impulse Derivation and Demonstration; Author: Flipping Physics;https://www.youtube.com/watch?v=9rwkTnTOB0s;License: Standard YouTube License, CC-BY