Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 7, Problem 7.105P
To determine
The rate of convection heat transfer from the argon plasma to the substrate. And the rate of latent heat release.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The condenser of a steam power plant consists of AISI 302 Stainless steel tubes, each with outer and inner diameters of 35 mm and 30 mm, respectively. Saturated steam at 0.135 bar condenses on the outer surface of the tube, while water at a mean temperature of 295 K is in fully developed flow through the tube (you can assume that 295 K is the mean temperature in the axial direction of the tube (e.g. along its length) or you may assume that the inlet water temperature is 295 K).
For a water mass flow rate of 0.22 kg/s, what is the outer surface temperature of the tube and the rates of heat transfer and steam condensation per unit tube length? As an approximation you may evaluate the properties of the liquid film at the saturation temperature.
FROM BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
a film-type condenser consists of a packed bed of 3-cm diameter spheres with a voidage of 35%. water sprayed onto the bed at 60oC is used to condense steam entering at the base at a saturation temperature of 100oC. How deep must the bed be to ensure complete condensation of the steam, and what is the outlet temperature of the water? (Use water properties based on the mean of the inlet and outlet water temperatures, and iterate if necessary)
Chapter 7 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 7 - Consider the following fluids at a film...Ch. 7 - Engine oil at 100C and a velocity of 0.1 m/s flows...Ch. 7 - Consider steady, parallel flow of atmospheric air...Ch. 7 - Consider a liquid metal (Pr1), with free stream...Ch. 7 - Consider the velocity boundary layer profile for...Ch. 7 - Consider a steady, turbulent boundary layer on and...Ch. 7 - Consider flow over a flat plate for which it is...Ch. 7 - A flat plate of width 1 m is maintained at a...Ch. 7 - An electric air heater consists of a horizontal...Ch. 7 - Consider atmospheric air at 25C and a velocity of...
Ch. 7 - Repeat Problem 7.11 for the case when the boundary...Ch. 7 - Consider water at 27°C in parallel flow over an...Ch. 7 - Explain under what conditions the total rate of...Ch. 7 - In fuel cell stacks, it is desirable to operate...Ch. 7 - The roof of a refrigerated truck compartment is of...Ch. 7 - The top surface of a heated compartment consists...Ch. 7 - Calculate the value of the average heat transfer...Ch. 7 - The proposed design for an anemometer to determine...Ch. 7 - Steel (AISI 1010) plates of thickness =6mm and...Ch. 7 - Consider a rectangular fin that is used to cool a...Ch. 7 - The Weather Channel reports that it is a hot,...Ch. 7 - In the production of sheet metals or plastics, it...Ch. 7 - An array of electronic chips is mounted within a...Ch. 7 - A steel strip emerges from the hot roll section of...Ch. 7 - In Problem 7.23. an anemometer design was...Ch. 7 - One hundred electrical components, each...Ch. 7 - The boundary layer associated with parallel flow...Ch. 7 - Forced air at 250C and 10 m/s is used to cool...Ch. 7 - Air at atmospheric pressure and a temperature of...Ch. 7 - Consider a thin, 50mm50mm fuel cell similar to...Ch. 7 - The cover plate of a flat-plate solar collector is...Ch. 7 - An array of 10 silicon chips, each of length...Ch. 7 - A square (10mm10mm) silicon chip is insulated on...Ch. 7 - A circular pipe of 25-mm outside diameter is...Ch. 7 - An L=1-m- long vertical copper tube of inner...Ch. 7 - A long, cylindrical, electrical heating element of...Ch. 7 - Consider the conditions of Problem 7.49, but now...Ch. 7 - Pin fins are to be specified for use in an...Ch. 7 - Prob. 7.52PCh. 7 - Prob. 7.53PCh. 7 - Hot water at 500C is routed from one building in...Ch. 7 - In a manufacturing process, long aluminum rods of...Ch. 7 - Prob. 7.58PCh. 7 - To determine air velocity changes, it is proposed...Ch. 7 - Determine the convection heat loss from both the...Ch. 7 - Prob. 7.63PCh. 7 - Prob. 7.64PCh. 7 - Prob. 7.67PCh. 7 - A thermocouple is inserted into a hot air duct to...Ch. 7 - Consider a sphere with a diameter of 20 mm and a...Ch. 7 - Prob. 7.76PCh. 7 - A spherical, underwater instrument pod used to...Ch. 7 - Worldwide. over a billion solder balls must be...Ch. 7 - Prob. 7.80PCh. 7 - Prob. 7.81PCh. 7 - Consider the plasma spray coating process of...Ch. 7 - Prob. 7.83PCh. 7 - Tissue engineering involves the development of...Ch. 7 - Consider temperature measurement in a gas stream...Ch. 7 - Prob. 7.89PCh. 7 - A preheater involves the use of condensing steam...Ch. 7 - Prob. 7.91PCh. 7 - A tube bank uses an aligned arrangement of...Ch. 7 - A tube bank uses an aligned arrangement of...Ch. 7 - Repeat Problem 7.94, but with NL=7,NT=10, and...Ch. 7 - Heating and cooling with miniature impinging jets...Ch. 7 - A circular transistor of 10-mm diameter is cooled...Ch. 7 - A long rectangular plate of AISI 304 stainless...Ch. 7 - A cryogenic probe is used to treat cancerous skin...Ch. 7 - Prob. 7.103PCh. 7 - Prob. 7.104PCh. 7 - Prob. 7.105PCh. 7 - Consider the packed bed of aluminum spheres...Ch. 7 - Prob. 7.108PCh. 7 - Prob. 7.109PCh. 7 - Prob. 7.111PCh. 7 - Packed beds of spherical panicles can be sintered...Ch. 7 - Prob. 7.114PCh. 7 - Prob. 7.116PCh. 7 - Prob. 7.117PCh. 7 - Prob. 7.118PCh. 7 - Prob. 7.119PCh. 7 - Prob. 7.120PCh. 7 - Dry air at 35°C and a velocity of 20 m/s flows...Ch. 7 - Prob. 7.123PCh. 7 - Benzene, a known carcinogen, has been spilled on...Ch. 7 - Prob. 7.125PCh. 7 - Prob. 7.126PCh. 7 - Condenser cooling water for a power plant is...Ch. 7 - Prob. 7.128PCh. 7 - In a paper-drying process, the paper moves on a...Ch. 7 - Prob. 7.131PCh. 7 - Prob. 7.132PCh. 7 - Prob. 7.133PCh. 7 - Prob. 7.134PCh. 7 - Prob. 7.136PCh. 7 - It has been suggested that heat transfer from a...Ch. 7 - Prob. 7.138PCh. 7 - Cylindrical dry-bulb and wet-bulb thermometers are...Ch. 7 - The thermal pollution problem is associated with...Ch. 7 - Cranberries are harvested by flooding the bogs in...Ch. 7 - A spherical drop of water, 0.5 mm in diameter, is...Ch. 7 - Prob. 7.143PCh. 7 - Prob. 7.144PCh. 7 - Prob. 7.145PCh. 7 - Prob. 7.146PCh. 7 - Prob. 7.147PCh. 7 - Consider an air-conditioning system composed of a...Ch. 7 - Prob. 7.149P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An oil preheater consists of a single tube of 10 mm diameter and 5 m length, with its surface maintained at by swirling combustion gases. The engine oil (new) enters at 175˚C. What flow rate must be supplied to maintain an oil outlet temperature of 100˚C? What is the corresponding heat transfer rate?arrow_forwardA plane-inclined pad thrust bearing is 160mm wide and 40mm long in the direction of sliding. The sliding velocity is 6 m/s and the bearing is supported so that the inlet film thickness is always three times the outlet film thickness. A load 18 kN is carried by the bearing and Tellus 37 oil is supplied at an inlet temperature of 40̊ C. Assuming that 80% of the heat generated in the bearing is carried away by the oil, describe the operating characteristics of the bearing (Pm, Q, F, tm,). Density is 875 kg/m3 and specific heat is Cp=1.880 J/g-K.arrow_forwardQuestion c d and e pleasearrow_forward
- I need help on this question: (This question requires the use of Roger & Mayhew Steam Property Tables) Saturated steam at 1 atm is condensed on the external surface of a copper tube withan outside diameter 16 mm and tube wall of thickness 0.5 mm. The tube is cooledinternally by water with a mass flow rate of 0.06 kg/s, which in turn is raised intemperature from 15 oC to 60 oC as it flows through the tube. (Take the heat-transfer coefficient at the condensing side as 10.0 kW/m2K and the isobaric specific heat-capacity of water as 4180 J/kg K.) a) To calculate the heat transfer rate to the cooling water b) To calculate the length of the tube c) Comment on how to enhance heat transfer in this case.arrow_forwardEthylene glycol with a mass flow rate of 0.01 kg / sec flows in a thin-walled pipe with a diameter of 3 mm. The pipe is in the form of a serpentine, and was lifted into a well-mixed water bath at 25 ° C. Calculate the heat transfer and pipe length required for the fluid to enter the pipe at 85 ° C and exit at 35 ° C?arrow_forwardWhat is the rate of rice husk consumption of a 2-ton grain dryer requiring to dry paddy from 22 to 14% in 8 hrs. The dryer overall thermal efficiency is 45%. Assume a heat of vaporization for paddy of 600 kCal/kg of moisture evaporated and heating value for rice husk of 3,000 kcal/kg.arrow_forward
- Hot outside air and recirculated air from the inside of the car are mixed, pass through a filter, and are then blown by a fan through the evaporator coil where the air is cooled as the fluid inside the refrigeration system evaporates. The cooled air is then supplied to the car interior to maintain the inside temperature at the desired level, 20⁰ The passenger compartment of the car has dimensions 2m long, 1.5m wide, and 1m high. The overall heat transfer coefficients, radial and additional heat fluxes are presented in below. Place Windows Overall Heat Transfer Coefficient 3.66 (W/m^2)/K 6.66 (W/m^2)/K No need to calculate No need to calculate Heat Flux TO BE CALCULATED TO BE CALCULATED Heat Transfer Rate Car Body Solar Irradiation Thermal loads per person The transmissivity of window glass to solar radiation is 0.76 and the absorptivity of the car interior is 0.3. The window glass area is 40% of the total compartment surface There is a maximum of two people in the car at any given…arrow_forwardCarbon dioxide (CO:) is used for the gas cooled reactor in shell and tube heat exchanger type steam generator (shown in Figure 2). 90000 kg/h entered to the exchanger under pressure and temperature of 4 bar and 500 °C respectively. The steam saturation temperature is 250 °C when the carbon dioxide leave the generator at 330°C. Presume the formed steam is saturated and dry. Using 25 mm inner diameter and 2 mm wall thickness, a copper tube is designed for CO; mass flow rate of 350000 kg/m'h. Neglect the thermal resistance of the steam side. (a) Determine number of tubes that should be used (b) Determine the length of the tubes Take the following properties for the carbon dioxide: Cp=1.172 KI/kg °C; u=0.0000298 Ns/m²; k=0.043 w/m °C; p=3.26 kg/m² Take k (Copper) = 384 W/m °C Water in (cold fluid) - 250°C CO, (hot fluid) in (f = 500°C) CO, out (2 - 330°C) Steam out (2 250°C)arrow_forwardShow and explain all the equations and constants required to calculate what the exit temperature "To" of a fluid traveling through a copper pipe buried fairly deeply in typical organic soil at temperature "S" with the temperature of the fluid entering the pipe at "Ti". The pipe is of length "L" and the outside diameter is "d" with a wall thickness of "t". The fluid is water, but provide a solution which would accommodate other fluids. The fluid is flowing at a rate of "R" Liters per second. Express all your work in SI units.arrow_forward
- Hi, kindly help me with this problem and show the complete solution. Please explain it also thank you so mucharrow_forwardDesign a hydrocooling unit that can cool fruits andvegetables from 30 to 5°C at a rate of 20,000 kg/h under thefollowing conditions:The unit will be of flood type, which will cool the productsas they are conveyed into the channel filled with water. Theproducts will be dropped into the channel filled with water atone end and be picked up at the other end. The channel canbe as wide as 3 m and as high as 90 cm. The water is to becirculated and cooled by the evaporator section of a refrigerationsystem. The refrigerant temperature inside the coils is tobe 22°C, and the water temperature is not to drop below 1°Cand not to exceed 6°C.Assuming reasonable values for the average product density,specific heat, and porosity (the fraction of air volume ina box), recommend reasonable values for (a) the water velocitythrough the channel and (b) the refrigeration capacity ofthe refrigeration system.arrow_forward8.21 WP In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at o.2 m/s through a straight thin- walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform temperature profile, what is the surface temperature at the tube exit and at a distance of o.5 m from the entrance? Fluid properties may be approximated as p = 1000 kg/m³, c, = 4000 J/kg · K, µ = 2 × 10-3 kg/s · m, k = 0.8 W/m · K, and Pr = 10.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license