PRECISION MACHINING TECHNOLOGY PACKAGE
3rd Edition
ISBN: 9780357262788
Author: Hoffman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6.2, Problem 11RQ
Sketch a corner-rounding endmill.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
You are asked to design a unit to condense ammonia. The required condensation rate is 0.09kg/s. Saturated ammonia at 30 o C is passed over a vertical plate (10 cm high and 25 cm wide).The properties of ammonia at the saturation temperature of 30°C are hfg = 1144 ́10^3 J/kg andrho_v = 9.055 kg/m 3 . Use the properties of liquid ammonia at the film temperature of 20°C (Ts =10 o C):Pr = 1.463
rho_l= 610.2 kf/m^3
liquid viscosity= 1.519*10^-4 kg/ ms
kinematic viscosity= 2.489*10^-7 m^2/s
Cpl= 4745 J/kg C
kl=0.4927 W/m C
hfg*=hfg+0.68Cpl(Tsat-Given Ts)
a) Instead of one plate you want to use small plates and install many of them. Calculate the requiredsurface temperature to achieve the desired condensation rate (0.09 kg/s) if you install 36vertical plates (with the same dimension as above: 10 cm high and 25 cm wide).
11-19
designed
in Problem
The shaft shown in figure P11-4 was
10-19, for the data in the row(s) assigned from table
PII-1, and the corresponding diameter of shaft found
in Problem 10-19, design suitable bearings
5 E8 cycles at
the load for at least
State all assumptions.
to support
1200rpm.
(a) Using hydrodynamically lubricated bronze sleeve
bearings with ON = 40, Lld = 0.8, and clearance ratio
0.0025.
of
a
← gear
T
gear
Key
figure PI-4
Given
from the problem
10-19 we get d= 1.153 in
from the table 11-1 we get
a = 16 in
b= 18in
L= 20in
In an irrigation system, the following characteristics of the pipe network are available.• 100 meters of 4" PVC pipe, 3 gate valves• 500 meters of 3" PVC pipe, 4 gate valves• 200 meters of 2" H.G. pipe, 2 globe valves• 50 litres per second circulate in the pipes:Calculate:1. Total energy losses in meters.2. Leaks in pipes.3. Losses in accessories.4. Calculate the equivalent pipe of that system assuming only pipes without fittings.Solve the problem without artificial intelligence, solve by one of the experts
Chapter 6 Solutions
PRECISION MACHINING TECHNOLOGY PACKAGE
Ch. 6.1 - What part of the vertical milling machine allows...Ch. 6.1 - Briefly describe the direction of movement...Ch. 6.1 - When a table handle is turned clockwise the table...Ch. 6.1 - What distance does the saddle or table usually...Ch. 6.1 - Prob. 5RQCh. 6.1 - Briefly describe the function of the turret and...Ch. 6.1 - What is the name of the taper found in most modem...Ch. 6.1 - What part of the vertical mill can be raised and...Ch. 6.1 - How can power quill feed be automatically stopped...Ch. 6.1 - What is a benefit of using a DRO instead of...
Ch. 6.2 - Many of the cutters used in machining are made of...Ch. 6.2 - What is the major advantage of using...Ch. 6.2 - Prob. 3RQCh. 6.2 - What type of cutting tool would most likely be...Ch. 6.2 - Which type of cutter would most likely be used to...Ch. 6.2 - What workpiece factors might cause a four-flute...Ch. 6.2 - List three types of milling cutters that are used...Ch. 6.2 - Most manual vertical milling machine spindles are...Ch. 6.2 - A __________ is used to retain the toolholder in...Ch. 6.2 - What type of toolholder might he selected for...Ch. 6.2 - Sketch a corner-rounding endmill.Ch. 6.2 - What toolholding device uses two drive keys and a...Ch. 6.2 - Prob. 13RQCh. 6.2 - List the four basic pieces of a step clamp set: a....Ch. 6.2 - Prob. 15RQCh. 6.2 - Irregularly shaped work may be held in a custom...Ch. 6.3 - List five safety guidelines to observe when...Ch. 6.3 - Briefly describe the process of aligning a milling...Ch. 6.3 - What is chip load?Ch. 6.3 - Define IPM.Ch. 6.3 - Calculate spindle speed and feed for the two...Ch. 6.3 - Briefly describe the process of locating the...Ch. 6.3 - What are two benefits of boring over other...Ch. 6.3 - What are face milling and peripheral milling?Ch. 6.3 - When squaring a block on the vertical mill, what...Ch. 6.3 - What are the three basic methods used to mill...Ch. 6.3 - What must first be done before milling with either...Ch. 6.3 - Prob. 12RQCh. 6.3 - What diameter cutter should be used to create...Ch. 6.3 - When roughing a pocket, should you machine in a...Ch. 6.4 - What is a rotary axis?Ch. 6.4 - Define the term indexing.Ch. 6.4 - Describe the primary differences between the...Ch. 6.4 - Name three types of workpiece features that are...Ch. 6.4 - Briefly describe the two alignment steps that need...Ch. 6.4 - If the outside of a 6"-diameter disk is to be...Ch. 6.4 - What is the gear ratio found in the gear train of...Ch. 6.4 - When using the indexing head, a __________ can be...Ch. 6.4 - A workpiece requires 9 divisions. Calculate the...Ch. 6.4 - In the formula 40D=T,what do T and D represent?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a series pipe, calculate the diameter 2 according to the following:• Ltotal: 325 m• L1: 52 m, D1: 3/4"• L2: 254 m, D2:?• L3: 19 m, D: 1-1/4".Indicate the nominal diameter. Solve without using artificial inteligence, solve by one of the expertsarrow_forwardWhat is the critical speed of the shaft in rad/s for one, two, and three elements?arrow_forward2. Express the following complex numbers in rectangular form. (a) z₁ = 2еjл/6 (b) Z2=-3e-jπ/4 (c) Z3 = √√√3e-j³/4 (d) z4 = − j³arrow_forward
- A prismatic beam is built into a structure. You can consider the boundary conditions at A and B to be fixed supports. The beam was originally designed to withstand a triangular distributed load, however, the loading condition has been revised and can be approximated by a cosine function as shown in the figure below. You have been tasked with analysing the structure. As the beam is prismatic, you can assume that the bending rigidity (El) is constant. wwo cos 2L x A B Figure 3: Built in beam with a varying distributed load In order to do this, you will: a. Solve the reaction forces and moments at point A and B. Hint: you may find it convenient to use the principal of superposition. (2%) b. Plot the shear force and bending moment diagrams and identify the maximum shear force and bending moment. (2%) c. Develop an expression for the vertical deflection. Clearly state your expression in terms of x. (1%)arrow_forwardQuestion 1: Beam Analysis Two beams (ABC and CD) are connected using a pin immediately to the left of Point C. The pin acts as a moment release, i.e. no moments are transferred through this pinned connection. Shear forces can be transferred through the pinned connection. Beam ABC has a pinned support at point A and a roller support at Point C. Beam CD has a roller support at Point D. A concentrated load, P, is applied to the mid span of beam CD, and acts at an angle as shown below. Two concentrated moments, MB and Mc act in the directions shown at Point B and Point C respectively. The magnitude of these moments is PL. Moment Release A B с ° MB = PL Mc= = PL -L/2- -L/2- → P D Figure 1: Two beam arrangement for question 1. To analyse this structure, you will: a) Construct the free body diagrams for the structure shown above. When constructing your FBD's you must make section cuts at point B and C. You can represent the structure as three separate beams. Following this, construct the…arrow_forwardA cantilevered rectangular prismatic beam has three loads applied. 10,000N in the positive x direction, 500N in the positive z direction and 750 in the negative y direction. You have been tasked with analysing the stresses at three points on the beam, a, b and c. 32mm 60mm 24mm 180mm 15mm 15mm 40mm 750N 16mm 500N x 10,000N Figure 2: Idealisation of the structure and the applied loading (right). Photograph of the new product (left). Picture sourced from amazon.com.au. To assess the design, you will: a) Determine state of stress at all points (a, b and c). These points are located on the exterior surface of the beam. Point a is located along the centreline of the beam, point b is 15mm from the centreline and point c is located on the edge of the beam. When calculating the stresses you must consider the stresses due to bending and transverse shear. Present your results in a table and ensure that your sign convention is clearly shown (and applied consistently!) (3%) b) You have identified…arrow_forward
- 7.82 Water flows from the reservoir on the left to the reservoir on the right at a rate of 16 cfs. The formula for the head losses in the pipes is h₁ = 0.02(L/D)(V²/2g). What elevation in the left reservoir is required to produce this flow? Also carefully sketch the HGL and the EGL for the system. Note: Assume the head-loss formula can be used for the smaller pipe as well as for the larger pipe. Assume α = 1.0 at all locations. Elevation = ? 200 ft 300 ft D₁ = 1.128 ft D2=1.596 ft 12 2012 Problem 7.82 Elevation = 110 ftarrow_forwardHomework#5arrow_forwardA closed-cycle gas turbine unit operating with maximum and minimum temperature of 760oC and 20oC has a pressure ratio of 7/1. Calculate the ideal cycle efficiency and the work ratioarrow_forwardConsider a steam power plant that operates on a simple, ideal Rankine cycle and has a net power output of 45 MW. Steam enters the turbine at 7 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa by running cooling water from a lake through the tubes of the condenser at a rate of 2000 kg/s. Show the cycle on a T-s diagram with respect to saturation lines, and determine The thermal efficiency of the cycle,The mass flow rate of the steam and the temperature rise of the cooling waterarrow_forwardTwo reversible heat engines operate in series between a source at 600°C, and a sink at 30°C. If the engines have equal efficiencies and the first rejects 400 kJ to the second, calculate: the temperature at which heat is supplied to the second engine, The heat taken from the source; and The work done by each engine. Assume each engine operates on the Carnot cyclearrow_forwardA steam turbine operates at steady state with inlet conditions of P1 = 5 bar, T1 = 320°C. Steam leaves the turbine at a pressure of 1 bar. There is no significant heat transfer between the turbine and its surroundings, and kinetic and potential energy changes between inlet and exit are negligible. If the isentropic turbine efficiency is 75%, determine the work developed per unit mass of steam flowing through the turbine, in kJ/kgarrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License