Concept explainers
The price of coal that will enable the IGCC plant to recover their cost difference from fuel saving in 3 year.
Answer to Problem 29P
The price of coal that will enable the IGCC plant to recover their cost difference from fuel saving in 3 year is
Explanation of Solution
Determine the construction costs of coal.
Determine the construction costs of IGCC.
Determine the construction costs difference of coal and IGCC.
Determine the amount of electricity produced by either plant in 5 years.
Here, the power generation capacity of power plant is
Determine the amount of fuel needed to generate a specified amount of power.
Here, the efficiency of plant is
Determine the mass difference between plants.
Here, the mass of the coal in coal plant is
Determine the unit cost of coal per ton used in the power plant.
Here, the construction cost difference is
Conclusion:
Substitute
Substitute
Substitute
Substitute
For coal plant,
Substitute
For IGCC plant,
Substitute
Substitute
Substitute
Thus, the price of coal that will enable the IGCC plant to recover their cost difference from fuel saving in 3 year is
Want to see more full solutions like this?
Chapter 6 Solutions
Thermodynamics: An Engineering Approach
- 6–88 In tropical climates, the water near the surface of the ocean remains warm throughout the year as a result of solar energy absorption. In the deeper parts of the ocean, how- ever, the water remains at a relatively low temperature since the sun's rays cannot penetrate very far. It is proposed to take advantage of this temperature difference and construct a power plant that will absorb heat from the warm water near the sur- face and reject the waste heat to the cold water a few hundred meters below. Determine the maximum thermal efficiency of such a plant if the water temperatures at the two respective locations are 24 and 3°C. 24°C Boiler Осean Pump Turbine Condenser 3°Carrow_forwardTwo parallel shafts whose centers are 10 meters apart are connected by an open belt drive with a V-belt with a groove angle of 30°. The diameter of the larger pulley is 1000 mm and that of the smaller pulley is 400 mm. The smaller pulley is running at 1000 rpm to deliver 10 kW of power. The mass of the belt is 1 kg/m. Taking centrifugal tension into account, determine the minimal cross-sectional area if the allowable tensile stress of the belt is 5 MPa. The coefficient of friction between the belt and the pulleys is 0.25.arrow_forwardA 600-MW steam power plant, which is cooled by a nearby river, has a thermal efficiency of 40 percent. Deter- mine the rate of heat transfer to the river water. Will the actual heat transfer rate be higher or lower than this value? Why?arrow_forward
- Determine Illustration and assumption for both problems. Thank youarrow_forward6-49 An air conditioner removes heat steadily from a house at a rate of 750 kJ/min while drawing electric power at a rate of 5.25 kW. Determine (a) the COP of this air conditioner and (b) the rate of heat transfer to the outside air.arrow_forwardA proposed wind farm installation is based on the use of thirty 2 MW wind turbines. The installed capital cost is estimated at $1000/kW and the annual operation and maintenance costs are estimated to be 3% of the original capital cost. Financing for the project is to come from two sources: (1) A 20-year loan at 7% (75%), and (2) an equity investment that has a return of 15% (25%). The average capacity factor of the wind farm is estimated to be 0.35. Determine the estimated cost of energy ($/kWh) from this proposed wind farm.arrow_forward
- HW9 The angle embraced is 175° and the coefficient of friction between the belt and the pulley is 0.25. A leather belt is required to transmit 9.5 kW from a pulley 10 cm in diameter, running at 200 r.p.m.. If the safe working stress for the leather belt is 2 MPa, density of leather 1000 Kg/m and thickness of belt 1 cm, determine the width of the belt taking centrifugal tension into account. IIII 10arrow_forwardThe heat engine in the figure receives 1 MW of energy from the high temperature heat well. Heat The temperature of its source is 550 ° C. Some of the energy received by the heat machine is 300 K heat at the temperature of the well. Power generated by heat machine 450 KW . Calculate how much energy the heat machine puts into the heat well. In addition, the thermal Calculate the efficiency of this efficiency with the efficiency in the case of a Carnot machine. compare. Interpret the result with the reasonsarrow_forwardIn a fossil fuel power plant the chemical energy stored in fossil fuels such as coal, fuel oil, natural gas or oil shale and oxygen of the air converted successively into thermal energy, mechanical energy and, finally, electrical energy. now assume that a coal-fired plant with a capacity of 100 MW uses coal as an energy source to produce heat which later converted to electrical energy with 60% efficiency (40% is lost as heat). The total heat of coal is given 6000 kcal/kg. The combustion temperature for steam is 100-celsius degrees. The cooling water is provided from a river with an ambient temperature of 25 Celcius degrees. The power plant operates 24 hours per day. Based on the information given in the problem, Calculate; a) How many tons of coal should be used in this power plant? b) What is the Daily amount of DI water for the production of steam? c) What is the Daily amount of cooling water for condensation?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY