Explanation Given information: The beam is made of elastic perfectly plastic material. The allowable stress in the section is σ Y = 345 MPa . Explanation: Determination of Elastic moment: Moment of inertia: Show the free-body diagram of the beam as in Figure 1. The section is symmetrical about both the x and y directions. Determine the moment of inertia of the sectionusing the formula. I = b 1 ( d 1 ) 3 12 + b 2 ( d 2 ) 3 12 + b 3 ( d 3 ) 3 12 (1) Here, b 1 is width of section 1, d 1 is depth of section 1, b 2 is width of section 2, d 2 is depth of section 2, b 3 is width of section 3, and d 3 is the depth of section 3. Substitute 100 mm b 1 , 300 mm for d 1 , 100 mm for b 2 , 100 mm for d 2 , 100 mm for b 3 , and 100 mm for d 3 in Equation (1). I = 100 × 300 3 12 + 100 × 100 3 12 + 100 × 100 3 12 = 2.417 × 10 8 mm 4 × ( 1 m ) 4 ( 1,000 mm ) 4 = 0.2417 × 10 − 3 m 4 Elastic moment: Determine the elastic moment using the equation. M Y = σ Y I c (2) Here, σ Y is allowable stress in the beam and c is the distance between the centroidal distance. Substitute 345 MPa for σ Y , 0.2417 × 10 − 3 m 4 for I and 150 mmfor c in Equation (2). M Y = 345 MPa × 10 6 N/m 2 1 MPa × 0.2417 × 10 − 3 150 mm × 1 m 1,000 mm = 555 , 8333

Mechanics of Materials, Student Value Edition Plus Mastering Engineering with Pearson eText -- Access Card Package (10th Edition)

10th Edition

ISBN: 9780134326054

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Videos

Question

Chapter 6.10, Problem 6.168P

To determine

The maximum elastic moment and the plastic moment that can be applied to the cross section.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 6.10, Problem 6.167P

Chapter 6.10, Problem 6.169P

Students have asked these similar questions

Q Derive (continuity equation)? I want to derive clear mathematics.

motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

Chapter 6 Solutions

Mechanics of Materials, Student Value Edition Plus Mastering Engineering with Pearson eText -- Access Card Package (10th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.