FUND OF ENG THERMODYN(LLF)+WILEYPLUS
9th Edition
ISBN: 9781119391777
Author: MORAN
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Question
error_outline
This textbook solution is under construction.
Students have asked these similar questions
1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state.
I already figured…
1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The products of combustion leave this process at the dead state.
Asnwer:
The…
Given information is attached.
A. Estimate the temperature of the saturated steam at 15.0 bar. (In degrees Celsius)
B. Estimate the temperature of the superheated steam at 20.0 bar.
Knowledge Booster
Similar questions
- Air occupies a 0.5-m' tank. It starts at a pressure of 5 bar and a temperature of 300 K. Energy flows into the tank via heat transfer until the temperature reaches 400 K. This happens at constant pressure, which is possible because there is a pressure-relief valve that lets air leave the tank to keep the pressure constant. Neglect kinetic and potential energy effects, and use the ideal gas model with constant specific heats evaluated at 350 K. 4. Determine the mass of air that escapes, in kg. Determine the amount of energy transfer by heat, in kJ. a. b. Hint: use Ucv = mu; he u+ RT, and cv+ R= Cp.arrow_forwardQ-1(c): Consider a case in which the air inside the pressurized cabin of a jet transport flying at some altitude of pressure, 0.9 atm and of temperature, 15°C. The total volume of air at any instant inside the cabin is 1800m3. If the air in the cabin is completely recirculated through the air conditioning system every 20 min, calculate the mass flow of air in kg/s through the system. I Answer:arrow_forwardNeed answer ASAP. Please be detailed and clear with your solution. II. In a piston-and-cylinder apparatus the initial volume of air is 90 L at a pressure of 130 Kpa abs and temperature of 26°C. If the pressure is doubled while the volume is decreased to 56 L, compute the following using R=0.287 KJ/kg-K. 1. Mass of air, in kg. * 2.Final temperature of the air in °C. *arrow_forward
- Determine the mass flow rate of air entering the air-handling unit, in lb/s, the volumetric flow rate in each 26-in. duct, in ft3/min, and the velocity in the 50-in. duct, in ft/s. Step by step solution please thank you.arrow_forwardCalculate the energy requirement to raise the temperature of 1 kg of water from 60 ° C of water to 100 ° C using the following approach; a. Use of mean specific heat = .... kJ. b. Enthalpy change in water - vapor saturation table = .... kJ.arrow_forward2.0 .A large mining company was provided with a 3000 cm' compressed air tank. Air pressure drops from 700 KPa to 180 KPa while the temperature remains unchanged at 28 °C .What percentage has the mass of air in the tank has been reduced ? Ans . 74%arrow_forward
- Q1.A refrigeration facility is cooling down 2.5 kg dry air per second from T = 35 degrees Celsius, %RH = 75% to 18 degrees Celsius. How much water will the facility condense per hour? *note: please provide complete solution. you may use psychometric chart if needed. please explain in detail, thank you.arrow_forward4. A cylinder contains 0.12 m³ of air at 1 atm and 90 °C. The air is compressed to a volume of 0.03 m³, The final pressure being 6 atm. Determine: a.) the value of n for the compression; b.) the increase in internal energy of air; and c.) the work done during compression.arrow_forward6. One pound of an ideal gas undergoes an isentropic process from 95.3 psig and a volume of 0.6 ft3 to a final volume of 3.6 ft³. If Cp = 0.124 and C, = 0.093 Btu/lb-R, what are T2, P2, AH and w.arrow_forward
- Saturated steam at P1=25 bar expands adiabatically through a throttling valve to P2=4 bar. If the quality of the steam at the valve inlet is x1=0.9 what is the quality x2 at the valve outlet Please respond ASAParrow_forwardNonearrow_forwardkg). Q3. The steam at 215 bar and 500 °C is supplied to a steam turbine. It expands to 40 bar and 280 °c. It is then reheated to 490 °C and expands to 8 bar and 270 °C. The steam coming out from the second expansion of the turbine is further reheated to 490 °C and expands to condenser pressure of 0.07 bar. The steam entering into the condenser is dry saturated. Assuming the pressure losses in first heater of 1 bar and in second heater 0.5 bar, find (a) the thermal efficiency and power developed if the flow of steam is 10 kg/s (b) the isentropic efficiency of the expansion stages. Neglect the pump work. Mis-n-n (42.8 %, 1738 kW,78.5%,95.4 %, 87%) Q4. The steam nt 100arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY