The identification of the pin 1 of an in line integrated circuit.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

Calculate the force in cable AB and the angle θ for the support system shown. Round your final answers to two decimal places.

1.53 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view D D 6 mm 18 mm B A B Side view 160 mm 120 mm A B Top view

CORRECT AND DETAILED HANDWRITTEN SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. 16: Determine (a) the maximum bending stress, (b)the maximum shearing stress, (c) compressive bending stress atthe roller support, and (d) the shearing stress 1 in below the topsurface of the beam at the location 1 ft to the right of the rollersupport in the simply supported beam shown in Fig. 8-70.ANS: (a) 21,945.313 lb/in2; (b) 1656.25 lb/in2; (c) 10,000 lb/in2; (d) 190.972 lb/in2

Answer 2

Question

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Answer 6

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.

Answer 7

Chapter 53, Problem 1RQ

To determine

The identification of the pin 1 of an in line integrated circuit.

Answer 8

Expert Solution & Answer

Explanation of Solution

Identifying the left hand side of the IC is done by looking for a notch on the top of the package. The top left pin is pin1 which is sometimes identified with a small dot next to it. 555 timer is an integrated circuit with eight pins which is widely used in industrial electronics.

The presence of a notch at an end or dot on one pin gives the identification of the pin 1. Thus, a notch or a dot is used to identify the pin 1 in 555 timer.