AUTMOTIVE TECH, TECH MANUAL & MIND TAP
6th Edition
ISBN: 9781305383180
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 52, Problem 1RQ
Name the three major assemblies that make up a disc brake.
Expert Solution & Answer
To determine
The three major assemblies used to make up a disc brake.
Answer to Problem 1RQ
The three major assemblies are hub and rotor assembly, a caliper assembly, and the brake pads assembly.
Explanation of Solution
The disc brakes are comprised of three assemblies which are hub and rotor assembly, a caliper assembly, and brake pads assembly. The hub and rotor assembly is divided into two parts i.e. hub and rotor in which hub is the part in which wheel is fitted and may carry wheel bearings also. The rotor is the part which is generally made up with cast iron and is machined in a way that it provides a friction surface for the brake pads.
The caliper assembly is the one which is fitted to convert the hydraulic pressure to the mechanical force and inspects for the lining wear by the hole which is present on top of it. Further, a caliper has a capacity of containing up to six cylinders and pistons that helps in providing same level of pressure distribution.
The brake pad assembly is made up of metal having linings which are either riveted or bonded to them. It helps in straddling the rotor due to its position on each side of calipers. The linings on pads are semi-metallic in nature.
Conclusion:
Thus, the three assemblies which are used in making disc brakes are hub and rotor assembly, a caliper assembly, and the brake pads assembly.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
In direct calorimetry, a person is placed in a large, water-insulated chamber. The chamber is kept at a constant temperature. While in the chamber, the subject is asked to perform a number of normal activities, such as eating, sleeping, and exercising. The rate of heat released from the subject’s body can be measured by the rate of heat gain by the water bath. Would direct calorimetry be a practical way to measure metabolic rate? Why or why not?A person is placed inside a calorimetric chamber for 24 hours. During this time, the 660-gallon water bath heats up by 3.2°F. What is the subject’s metabolic rate during this period? Report your answer in kcal/day. Assume that there is no heat loss from the water to the surroundings.
Upon reentry into the Earth’s atmosphere, the bottom of a space shuttle heats up to dangerous levels as the craft slows for landing. If the velocity of the shuttle is 28,500 km/hr at the beginning of reentry and 370 km/hr just prior to landing, how much energy is lost as heat? The shuttle has a mass of 90,000 kg. Assume that the change in potential energy is negligible compared to the change in kinetic energy.
of the basket of the balloon at point A, and their other ends are staked to the ground. The hook is located in the geometric
center of the basket. The balloon and the air inside it have a combined mass of 3000 kg. You want to determine the
resultant of the tension forces in the four cables acting on the hook at point A. It is known that the magnitudes of the
tension in the cables are as follows: TAB = 207 N; TAC = 355 N; TAD = 250 N; and TAE = 486 N.
B
E
2.5 m
C
E
5.5 m
D
2.5 m
3.5 m
1.5 m
Using the information provided in the problem, express the force on the hook at point A by cable AC in rectangular component form.
The force on the hook at point A by cable AC in rectangular component form is given below.
T AC
N) i+
N) +
N) R
Chapter 52 Solutions
AUTMOTIVE TECH, TECH MANUAL & MIND TAP
Ch. 52 - Name the three major assemblies that make up a...Ch. 52 - Name the three types of calipers used on disc...Ch. 52 - What type of brake uses the inside of each rear...Ch. 52 - True or False? Disc brakes are not as likely to...Ch. 52 - What are the two basic types of brake rotors used...Ch. 52 - True or False? All calipers have at least one...Ch. 52 - What is the difference between floating and...Ch. 52 - What is rotor parallelism and how is it checked?Ch. 52 - Why is brake fluid removed from the master...Ch. 52 - Describe the procedure for using compressed air to...
Ch. 52 - List three conditions that dictate that a rotor...Ch. 52 - Give two main advantages of an on-vehicle lathe...Ch. 52 - What should be done to remove rust, corrosion, pit...Ch. 52 - Which term refers to variations in thickness of...Ch. 52 - Which of the following is not likely to cause a...Ch. 52 - Technician A says that a hard brake pedal on a...Ch. 52 - When replacing brake pads on a vehicle: Technician...Ch. 52 - When examining disc brakes: Technician A visually...Ch. 52 - Technician A cleans brake components in denatured...Ch. 52 - While discussing how to remove the piston from a...Ch. 52 - The functions of a splash shield are being...Ch. 52 - Technician A says that the piston seal retracts...Ch. 52 - Technician A says that fixed calipers use a piston...Ch. 52 - While installing new brake pads: Technician A...Ch. 52 - Loaded calipers are being discussed: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Water in the glass tube is at a temperature of 40°C. Plot the height of the water as a function of the tube's inner diameter D for 0.5mm≤D≤3mm. Use increments of 0.5mm. Take sigma=69.6mN/m, and theta=0° for the contact angle.arrow_forwardDetermine the distance h that the column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 68 F. Plot this relationship of h (vertical axis) versus D for 0.5 in≤D≤0.150in. Give values for increments of ΔD=0.025in. Discuss this resultarrow_forwardWater is at a temperature of 30 C. Plot the height h of the water as a function of the gap w between the two glass plates for 0.4 mm ≤ w ≤ 2.4 mm. Use increments of 0.4mm. Take sigma=0.0718 N/m.arrow_forward
- What is the reading on the vernier calipers? 7 6 0 5 10 8arrow_forwardDetermine the moments of the force about the x and the a axes. O 4 m F = {-40i +20j + 10k} N 3 m 6 m aarrow_forward6. A part of the structure for a factory automation system is a beam that spans 30.0 in as shown in Figure P5-6. Loads are applied at two points, each 8.0 in from a support. The left load F₁ = 1800 lb remains constantly applied, while the right load F₂ = 1800 lb is applied and removed fre- quently as the machine cycles. Evaluate the beam at both B and C. A 8 in F₁ = 1800 lb 14 in F2 = 1800 lb 8 in D RA B C 4X2X1/4 Steel tube Beam cross section RDarrow_forward
- 30. Repeat Problem 28, except using a shaft that is rotating and transmitting a torque of 150 N⚫m from the left bear- ing to the middle of the shaft. Also, there is a profile key- seat at the middle under the load.arrow_forward28. The shaft shown in Figure P5-28 is supported by bear- ings at each end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as pos- sible while keeping the stress safe. Determine the required d = 20mm D = ? R = ?| 5.4 kN d=20mm Length not to scale -a = ?- +а= a = ? + -125 mm- -250 mm- FIGURE P5-28 (Problems 28, 29, and 30)arrow_forward12. Compute the estimated actual endurance limit for SAE 4130 WQT 1300 steel bar with a rectangular cross sec- tion of 20.0 mm by 60 mm. It is to be machined and subjected to repeated and reversed bending stress. A reli- ability of 99% is desired.arrow_forward
- 28. The shaft shown in Figure P5-28 is supported by bear- ings at each end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as pos- sible while keeping the stress safe. Determine the required d = 20mm D = ? R = ?| 5.4 kN d=20mm Length not to scale -a = ?- +а= a = ? + -125 mm- -250 mm- FIGURE P5-28 (Problems 28, 29, and 30)arrow_forward2. A strut in a space frame has a rectangular cross section of 10.0 mm by 30.0 mm. It sees a load that varies from a tensile force of 20.0 kN to a compressive force of 8.0 kN.arrow_forwardfind stress at Qarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License