Electricity for Refrigeration, Heating, and Air Conditioning
9th Edition
ISBN: 9781285179988
Author: Russell E. Smith
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 5RQ
To determine
The major difference between a contactor and a relay.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What is the Relay Number and its law?
Draw a series circuit with a thermostat,a low-pressure switch, and a highpressure switch used as safety controlsto protect a motor
What happens when the low-voltage current flow in the coil primary winding is interrupted by the switching device?
The primary winding delivers a high-voltage spark to the plugs.
The magnetic field in the coil primary builds.
The secondary voltage drops to zero volts.
High voltage is induced in the secondary windin
Chapter 5 Solutions
Electricity for Refrigeration, Heating, and Air Conditioning
Ch. 5 - What are the three types of electrical diagrams...Ch. 5 - A load is an electrical device that __________. a....Ch. 5 - What is the major load of an air-conditioning...Ch. 5 - Identify the following symbols for loads:Ch. 5 - Prob. 5RQCh. 5 - What do the terms normally open and normally...Ch. 5 - What is the difference between a magnetic starter...Ch. 5 - Prob. 8RQCh. 5 - Draw a heating and a cooling thermostat and...Ch. 5 - A three-pole contactor would allow how many paths...
Ch. 5 - A disconnect switch is used to __________. a. open...Ch. 5 - What determines whether a pressure switch opens or...Ch. 5 - Identify the following symbols for...Ch. 5 - What is the difference between a thermal overload...Ch. 5 - What is the purpose of a transformer? Draw the...Ch. 5 - Which of the following is not a requirement for an...Ch. 5 - What is the purpose of a legend on a schematic...Ch. 5 - A factual diagram is _____. a. a pictorial diagram...Ch. 5 - Identify the following symbols for safety devices.Ch. 5 - Prob. 20RQCh. 5 - True or False: The schematic diagram tells service...Ch. 5 - What is the difference between a pilot duty and a...Ch. 5 - What type of switch would be used to open or close...Ch. 5 - What is the purpose of a fuse in an electrical...Ch. 5 - True or False: A solenoid valve is a device that...Ch. 5 - What is a signal light used for in a control...Ch. 5 - Change the following normally open elements from...Ch. 5 - Draw the symbols for the following electrical...Ch. 5 - Add letter designations to the symbols to indicate...Ch. 5 - Draw a symbol for a magnetic starter.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the primary use of a limit switch?arrow_forwardAn open winding in an electric motor means that A. the winding is making contact with the motor frame. B. one winding is making contact with another winding. C. a wire in one winding is broken. D. the centrifugal switch to the start winding is open.arrow_forwardRefer to Figure 211 to answer the following questions. How much voltage will be applied to coil 1CR when it is energized?arrow_forward
- Why are the contacts of a micro switch spring loaded?arrow_forwardSelect the proper choice(s) for each of the following statements: 1) To control single-acting cylinder we just need: double-acting cylinder we should use A2/2-way, 5/2-way, (C) 3/3-way, 3/4-way, 2) In DCV. (B) 3/2-way, 4/2-way, (D) 4/3-way, 3/2-way. mid poistion of DCV, we can move cylinder piston rod freely without resistance by hand. (A) working ports are exhausted, (C) working ports are pressurized, 3) In pneumatics we use A Compressor (B) Pump, DCV, while to control the 4) Quick exhaust valve is used to (A) increase the cylinder return speed. (C) meter-out the cylinder speed (B) all ports are closed. no one of these options. to obtain high pressure air. (C) Turbine, (D) pressure relief valve. (B) meter-in the cylinder speed, (D) increase the cylinder extending speed. 6) Meter-in of cylinder movement is used to control the Afluid that enters the hydraulic cylinder, (B) fluid that exits the hydraulic cylinder, (C) fluid that enters the DCV (D) fluid that exits the DCV. 5) One of the…arrow_forwardHow many transformers are needed to make an open-delta connection?arrow_forward
- What two factors determine the amount of voltage produced by a thermocouple?arrow_forwardWhat is the average voltage drop of an SCR when it is turned on?arrow_forwardA three-phase motor nameplate indicates a full load current of 362 amperes. The nameplate indicates that the heaters are to be sized for 125% of motor full load current. Current transformers with a ratio of 600:5 are used to reduce the motor current. Using the chart shown in Figure 4–7B, determine the size of overload heaters needed to protect this motor.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning