Fundamentals of Electromagnetics with Engineering Applications
Fundamentals of Electromagnetics with Engineering Applications
1st Edition
ISBN: 9780470105757
Author: Stuart M. Wentworth
Publisher: Wiley, John & Sons, Incorporated
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 5, Problem 5.1P

Starting with Maxwell’s equations for simple, charge free media, derive the Helmholtz equation for H.

Expert Solution & Answer
Check Mark
To determine

The Helmholtz equation for magnetic field H .

Answer to Problem 5.1P

The Helmholtz equation for magnetic field H is 2H=μσHt+με2Ht2 .

Explanation of Solution

Given:

The Maxwell’s equations are simple and the media is free of any charge.

Concept used:

The equation of Ampere’s circuital law for simple and charge free media is shown below.

  ×H=σE+εEt ....... (1)

The equation of Faraday’s law is shown below.

  ×E=μHt

Calculation:

The condition for charge free media is H=0 .

Take curl on both sides of equation (1) as shown below.

  ×(×H)=×(σE+ε E t)=×(σE)+×(ε E t)=σ(×E)+ε(× E t)

Since, the right side of above equation is a position derivative that acts on time derivative, so the above equation can be written as,

  ×(×H)=σ(×E)+εt(×E)

Substitute μHt for ×E in above equation.

  ×(×H)=σ(μ H t)+εt(μ H t)=μσHtμεt( H t)=μσHtμε2Ht2

The curl of curl of any vector is equal to the divergence and Laplacian, so the above equation can be written as,

  H2H=μσHtμε2Ht2

Due to charge free medium the value of divergence of magnetic field H is equal to 0 .

Now, the above equation can be written as,

  2H=μσHtμε2Ht22H=μσHt+με2Ht2

The above equation is known as Helmholtz wave equation for magnetic field H .

Therefore, the Helmholtz equation is 2H=μσHt+με2Ht2 .

Conclusion:

Thus, the Helmholtz equation for magnetic field H is 2H=μσHt+με2Ht2 .

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
"Using emu8086 programming, I need two different solutions based on a source." Write an assembly language program to execute of the following tasks: 1. Execute the operation of an EX-NOR (exclusive nor) without utilizing the XOR instruction. 2. Without using DIV instruction, divide the content AX by (L=8).
"I need proof in the solution and a supported source with the solution." Choose the correct answer 1. the maximum memory capacity that can be connected to 8086 microprocessor is a. 64 KB b. 128 KB. c. 1MB d. 4MB 2. The hexadecimal representation of decimal number (107) 10 is a. 8B b. 5A c. 4E d. 6B 3. which of the following instruction not valid a. MOV AL,BL b. MOV DS,5000H, c. MOV AX,5000H d. PUSH AX 4. PIC16F877A microcontroller has ------ pins a. 28, b. 32, c 40 d. 64 5. the letter F in PIC16F877A microcontroller means ---- a. flash b. flag c. family d. float 6. the length of the 8086 address bus is------- a. 16 b. 20 c. 32 d. 64 7. CS used with offset to generate physical address in code segment a. DI b. SI c. IP d. BP 8. 8086 microprocessor can fetch up to ------ instruction by instruction queue mechanism a. 2 b. 4 c. 6 d.8 PIC16F877A microcontroller has analog multiplexed ports 9. a. 2 b. 4 c. 5 d. 8 10. The content of SP when execute POP instruction a. Increased by 2 b.…
"I need proof in the solution and a supported source with the solution.' Choose the correct answer for the following sentences d. 32 .. The 8086 microprocessor has --------- data pin's a. 8 b. 16 c. 20 2. The 8086 microprocessor has a. 16 b. 8 c. 32 d. 20 3. SP & address pin's used with stack segment register (SS) to access memory within the stack segment a. BP b. IP c. SI d. DI 4. If CS 002AH and IP- 0023H, the physical address is ----- a. 002C3H b. 0023H1 c. 002A1H d. 0023H 5. POP instruction used to the stack a. Read b. Write c. Reset d. Set 6. PIC16F877A microcontroller has ------ digital I/O ports a. 2 b.4 c. 5 d. 8 7. PIC16F877A microcontroller has analog multiplexed ports b. 2 b. 4 c. 5 d. 8 8. used to control the brightness of LED connected to Arduino a. Analog input b. analog output c. digital input d. digital output 9. The content of SP when execute PUSH instruction a. Increased by 2 b. decreased by 2 c. multiplied by 2 d. divided by 2 10. If CS-002B & IP-0013, physical…

Chapter 5 Solutions

Fundamentals of Electromagnetics with Engineering Applications

Knowledge Booster
Background pattern image
Electrical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON
Text book image
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Text book image
Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education
Text book image
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education
Text book image
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON
Text book image
Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,
How do Electric Transmission Lines Work?; Author: Practical Engineering;https://www.youtube.com/watch?v=qjY31x0m3d8;License: Standard Youtube License