Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 48, Problem 12SQ
To determine
Explain how the feeder motor is protected for an overload condition in the Figure 48-9.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Explain the different methods of breaking DC Motors
23. When the circuit breaker is always tripping, most likely
There is an overloading
c. The supply line are open
a.
b.
There is an over current
d. The load is removed
24. The synchronous motor is not inherently self- starting because
the rotating magnetic field does not have enough poles
b. the rotating magnetic field is produced by only 50 HZ frequency currents
the force required to accelerate the rotor is to the synchronous speed in an instant is
d. the starting devices to accelerate the rotor to near synchronous speed is absent
25. Synchronous motor has speed
a. slight drop in speed on full load
b.high speed at low torque
а.
с.
c. constant speed
d. low speed at high -
1- What is the starting torque developed by a split-phase or a capacitor start
motor?
2- What is the current in-rush at the time of starting the motor? Does it cause
severe fluctuations on the line?
Chapter 48 Solutions
Electric Motor Control
Ch. 48 - In Figure 482, what is the purpose of normally...Ch. 48 - Can a time-delay relay be used satisfactorily in a...Ch. 48 - Prob. 3SQCh. 48 - Prob. 4SQCh. 48 - Prob. 5SQCh. 48 - What is the purpose of the lockout relay or safety...Ch. 48 - What happens if the reverse push button is closed...Ch. 48 - Prob. 8SQCh. 48 - Prob. 9SQCh. 48 - In Figure 487, is it necessary to push the stop...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (B)- Indicate whether the following statements are true or false and correct the false statements 1- Wave wound armature has two parallel paths. 2- The current ratio is equal to 1/ turn ratio at no-load while the voltage ratio is equal to 1/ turn ratio at full load 5.4. 3-When a series de motor is operated without a load, the armature draws excessive current Ph 4- The hysteresis loss can be minimized by using core of thin laminations ل لهول 259 Ne 02arrow_forwardA 4 pole, 500V shunt motor has 720 wave connected conductors on its armature. The full load armature current is 60A and flux per pole is 0.03Wb. The armature resistance is 0.2Ω and contact drop per brush is 1V. What is the back emf? What is the developed torque?arrow_forwardExplain why the use of switching drives can be problematical when driving an inductive load, and how any problems may be overcomearrow_forward
- A 4-pole, 650v shunt motor has 720 wave connected conductors on its armature, The full-load armature current is 80A and the line flux per pole is 0,04Wb. The armature resistance is 0.4 ohms. Calculate the full load speed. Select the correct response: 548.80 rpm 321,88 rpm 643.75 грm 344.86 грmarrow_forwardExplain how does the current will be reduced during the starting of the motor.arrow_forwardOne type of failure that's more common with 200 HP motors than with 10 HP motors is A. rotor bar failure.B. contactor failure.C. bearing failure. D. stator failures.arrow_forward
- 8) No handwritten, only typing...arrow_forwardCan you give me all the different types of DC motor its quite confusing coz some info says it has only 4 which is series , shunt , compount , and permanent magnet which is only under the category of brushed DC motors it doesnt include yet the brushless and the sub category however when you recognize or notice that in flowchart there are several like the one self excited etc I wonder if its an updated version though but I need you to list all of them and explain each and what category or subcategory I mean the overall DC motors even in chatgpt there are some added like universal , stepper , servo , coreless and so on. Explain each one. Pls help me if you could summarize or elaborate all at once so that it would be easy to identify or determine the overall information and additionally per category should have definition as well as the followingarrow_forward1. Explain the working Principle of Single Phase Induction Motor. 2. What are the different types of Starters to control AC-Motor. Explain briefly. 3. Explain DOL starter of Single Phase Induction Motor briefly. 4. What is the purpose of the magnetic contactor? 5. What is the use of auxiliary contact in the magnetic controller? 6. What happens when the holding coil gets the supply in the magnetic controller? 7. Explain the working principle of a relay.arrow_forward
- Describe the operation of the pull-in and hold on windings in a pre-engaged starter solenoidarrow_forwardWhat two benefits do reactors in motors have?arrow_forwardA 4–pole, 500 V d.c. shunt motor has 720 wave–connected conductors on its armature. The full–load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Ω. What is the full–load speed of the motor?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...Mechanical EngineeringISBN:9781337399128Author:Russell E. SmithPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning
Electricity for Refrigeration, Heating, and Air C...
Mechanical Engineering
ISBN:9781337399128
Author:Russell E. Smith
Publisher:Cengage Learning