Concept explainers
The state of liquid water is changed from 50 psia and 50°F to 2000 psia and 100°F. Determine the change in the internal energy and enthalpy of water on the basis of the (a) compressed liquid tables, (b) incompressible substance approximation and property tables, and (c) specific-heat model.
(a)

The specific internal energy of water on the basis of the compressed liquid table.
The specific enthalpy of water on the basis of the compressed liquid table.
Answer to Problem 79P
The specific internal energy of water on the basis of the compressed liquid table is
The specific enthalpy of water on the basis of the compressed liquid table is
Explanation of Solution
Determine the change in an initial specific enthalpy of the liquid water.
Here, the specific enthalpy at 50 F temperature is
Determine the specific internal energy of water on the basis of the compressed liquid table.
Here, the initial specific internal energy of water is
Determine the specific enthalpy of water on the basis of the compressed liquid table.
Here, the initial specific enthalpy energy of water is
Conclusion:
From the Table A-4E, “Saturated water”, obtain the value of initial internal energy and enthalpy at temperature 50 F.
Substitute
From the Table A-7E, “Compressed liquid water”, obtain the value of final internal energy and enthalpy at pressure 2000 psia and temperature 100 F.
Substitute
Thus, the specific internal energy of water on the basis of the compressed liquid table is
Substitute
Thus, the specific enthalpy of water on the basis of the compressed liquid table is
(b)

The specific internal energy of water on the basis of the incompressible substance and property tables.
The specific enthalpy of water on the basis of the incompressible substance and property tables.
Answer to Problem 79P
The specific internal energy of water on the basis of the incompressible substance and property tables is
The specific enthalpy of water on the basis of the incompressible substance and property tables is
Explanation of Solution
Determine the specific internal energy of water on the basis of the incompressible substance and property tables.
Here, the initial specific internal energy of water is
Determine the specific enthalpy of water on the basis of the incompressible substance and property tables.
Here, the initial specific enthalpy energy of water is
Conclusion:
From the Table A-4E, “Saturated water”, obtain the value of initial internal energy and enthalpy at temperature 50 F and 100 F.
Substitute
Thus, the specific internal energy of water on the basis of the incompressible substance and property tables is
Substitute
Thus, the specific enthalpy of water on the basis of the incompressible substance and property tables is
(c)

The specific internal energy of water on the basis of the specific heat model.
Answer to Problem 79P
The specific internal energy of water on the basis of the specific heat model is
Explanation of Solution
Determine the specific heat of water.
Here, the specific heat of water is
Conclusion:
From the Table A-3E(a), “Properties of common liquids, solids, and foods”, obtain the value of specific heat of water is
Substitute
Thus, the specific internal energy of water on the basis of the specific heat model is
Want to see more full solutions like this?
Chapter 4 Solutions
THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I
- CORRECT AND DETAILED SOLUTION WITH FBD ONLY. I WILL UPVOTE THANK YOU. CORRECT ANSWER IS ALREADY PROVIDED. I REALLY NEED FBD. The roof truss shown carries roof loads, where P = 10 kN. The truss is consisting of circular arcs top andbottom chords with radii R + h and R, respectively.Given: h = 1.2 m, R = 10 m, s = 2 m.Allowable member stresses:Tension = 250 MPaCompression = 180 MPa1. If member KL has square section, determine the minimum dimension (mm).2. If member KL has circular section, determine the minimum diameter (mm).3. If member GH has circular section, determine the minimum diameter (mm).ANSWERS: (1) 31.73 mm; (2) 35.81 mm; (3) 18.49 mmarrow_forwardPROBLEM 3.23 3.23 Under normal operating condi- tions a motor exerts a torque of magnitude TF at F. The shafts are made of a steel for which the allowable shearing stress is 82 MPa and have diameters of dCDE=24 mm and dFGH = 20 mm. Knowing that rp = 165 mm and rg114 mm, deter- mine the largest torque TF which may be exerted at F. TF F rG- rp B CH TE Earrow_forward1. (16%) (a) If a ductile material fails under pure torsion, please explain the failure mode and describe the observed plane of failure. (b) Suppose a prismatic beam is subjected to equal and opposite couples as shown in Fig. 1. Please sketch the deformation and the stress distribution of the cross section. M M Fig. 1 (c) Describe the definition of the neutral axis. (d) Describe the definition of the modular ratio.arrow_forward
- using the theorem of three moments, find all the moments, I only need concise calculations with minimal explanations. The correct answers are provided at the bottomarrow_forwardMechanics of materialsarrow_forwardusing the theorem of three moments, find all the moments, I need concise calculations onlyarrow_forward
- Can you provide steps and an explaination on how the height value to calculate the Pressure at point B is (-5-3.5) and the solution is 86.4kPa.arrow_forwardPROBLEM 3.46 The solid cylindrical rod BC of length L = 600 mm is attached to the rigid lever AB of length a = 380 mm and to the support at C. When a 500 N force P is applied at A, design specifications require that the displacement of A not exceed 25 mm when a 500 N force P is applied at A For the material indicated determine the required diameter of the rod. Aluminium: Tall = 65 MPa, G = 27 GPa. Aarrow_forwardFind the equivalent mass of the rocker arm assembly with respect to the x coordinate. k₁ mi m2 k₁arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





