Understanding Motor Controls
3rd Edition
ISBN: 9781305498129
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 42, Problem 1RQ
What are the three main electrical test instruments used in troubleshooting?
Expert Solution & Answer
To determine
Three main electrical test instruments used in trouble shooting.
Explanation of Solution
An industrial electrician's main job is to troubleshoot or restore a control circuit when it fails. First, it is necessary to determine which component is at fault in order to repair or remove a faulty component. Three main instruments used to troubleshoot a circuit are the voltmeter, ohmmeter, and ammeter. They can measure several different electrical quantities, so this meters are called multimeters.
Thus Voltmeter, Ohmmeter, Ammeter are the main electrical test instruments used in trouble shooting.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Can you solve the question by finding initial angular acceleration of D then ueing it to calculate angular velocity of D.
: +0
usão
۲/۱
العنوان
on
Jon
14.23. A double-effect forward-feed
evaporator is required to give a product
consisting of 30 per cent crystals and a
mother liquor containing 40 per cent by
mass of dissolved solids. Heat transfer
coefficients are 2.8 and 1.7 kW/m² K in the
first and second effects respectively. Dry
saturated steam is supplied at 375 kN/m²
and the condenser operates at 13.5 kN/
m².
(a) What area of heating surface is
required in each effect assuming the
effects are identical, if the feed rate is 0.6
kg/s of liquor, containing 20 per cent by
mass of dissolved solids, and the feed
temperature is 313 K?
(b) What is the pressure above the boiling
liquid in the first effect?
The specific heat capacity may be
taken as constant at 4.18 kJ/kg K. and
the effects of boiling-point rise and of
hydrostatic head may be neglected.
Example(2):
Double effect evaporator is used for
concentrating a certain caustic soda
solution 10000kg/hr from 9wt% to
47wt%. The feed at 30°C enters the
first evaporator. Backward arrangement
evaporators are used. steam is available at
167.7°C and the vapor space in the second
effect is 14.6Kpa.
The overall heat transfer coefficients of
the two effects are 8380 and 6285kcal/
W.CH
ork
-conce
-SOLFFF
and-ans..
112.1
а
DiD
3
respectively and the specific heat capacity
of all caustic soda solution 3.771 KJ/Kg.
°C, determine the heat transfer area of
each effect
معدلة 5:48 م
O
Chapter 42 Solutions
Understanding Motor Controls
Ch. 42 - What are the three main electrical test...Ch. 42 - What is the advantage of a plunger type voltage...Ch. 42 - A motor is tripping out on overload. The motor...Ch. 42 - A motor is tripping out on overload. The motor...Ch. 42 - Prob. 5RQCh. 42 - Refer to the circuit shown in Figure 42–17. Assume...Ch. 42 - Prob. 7RQCh. 42 - Refer to the circuit shown in Figure 4221. Assume...Ch. 42 - Prob. 9RQCh. 42 - Refer to the circuit shown in Figure 42–21. Assume...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- give me solution math not explinarrow_forwardgive me solution math not explinarrow_forwarduse Q Strips of material 10 mm thick are dried under constant drying conditions from 28 to 13 per cent moisture in 25 ks. The equilibrium moisture content is 7 per cent. The relation between E, the ratio of the final free moisture content at time t to the initial free moisture content, and the parameter J is given by: E 1 0.64 0.49 0.38 0.295 0.22 0.14 J 0 0.1 0.2 0.3 0.5 0.6 العنوان 0.7 It may be noted that J = kt/12, where, k = constant, t = time (ks) 1 = thickness/2 of the sheet of material (mm) a. Based on the given data, plot a graph of E against J b. Determine the time taken to dry 60 mm planks from 22 to 10 per cent moisture under the same conditions assuming no loss from the edges? ina östler ۲/۱arrow_forward
- 14.25.2.5 kg/s of a solution at 288 K containing 10 per cent of dissolved solids is fed to a forward-feed double-effect evaporator, operating at 14 kN/m² in the last effect. If the product is to consist of a liquid containing 50 per cent by mass of dissolved solids and dry saturated steam is fed to the steam coils, what PROBLEMS 1179 should be the pressure of the steam? The surface in each effect is 50 m² and the coefficients for heat transfer in the first and second effects are 2.8 and 1.7 kW/ m² K, respectively. It may be assumed that the concentrated solution exhibits a boiling-point rise of 5 deg K, that the latent heat has a constant value of 2260 kJ/kg and that the specific heat capacity of the liquid stream is constant at 3.75 kJ/kg K Oarrow_forward: +0 العنوان use only 5) A 100 kg batch of granular solids containing 30% moisture is to be dried in a tray drier to 15.5% by passing a current of air at 350 K tangentially across its surface at a velocity of 1.8 m/s. If the constant rate of drying under these conditions is 0.7 g/s m2 and the critical moisture content is 15%, calculate the approximate drying time. Assume the drying surface to be 0.03 m2 /kg dry mass. мониarrow_forwardgive me solution math not explinarrow_forward
- ۲/۱ : +0 العنوان seoni 4) 1 Mg (dry weight) of a non-porous solid is dried under constant drying conditions with an air velocity of 0.75 m/s parallel to the drying surface. The area of drying surface is 55 m2 If initial rate of drying is 0.3 g/m2 s, how long it will take to dry a material from 0.15 to 0.025 kg water/kg dry solid? The critical moisture content is 0.125 and the equilibrium moisture is negligible. The falling rate of drying is linear in moisture content. If air velocity increases to 4 m/s, what will be the anticipated saving in drying time? 0 ostherarrow_forward14.23. A double-effect forward-feed evaporator is required to give a product consisting of 30 per cent crystals and a mother liquor containing 40 per cent by mass of dissolved solids. Heat transfer coefficients are 2.8 and 1.7 kW/m² K in the first and second effects respectively. Dry saturated steam is supplied at 375 kN/m² and the condenser operates at 13.5 kN/ m². (a) What area of heating surface is required in each effect assuming the effects are identical, if the feed rate is 0.6 kg/s of liquor, containing 20 per cent by mass of dissolved solids, and the feed temperature is 313 K? (b) What is the pressure above the boiling liquid in the first effect? The specific heat capacity may be taken as constant at 4.18 kJ/kg K. and the effects of boiling-point rise and of hydrostatic head may be neglected. O Oarrow_forward5) A 100 kg batch of granular solids containing 30% moisture is to be dried in a tray drier to 15.5% by passing a current of air at 350 K tangentially across its surface at a velocity of 1.8 m/s. If the constant rate of drying under these conditions is 0.7 g/s m2 and the critical moisture content is 15%, calculate the approximate drying time. Assume the drying surface to be 0.03 m2 /kg dry mass. Oarrow_forward
- Solve for v and Iarrow_forwardG = 0.350MPa, P = 900N, a=20mm, b=50mm, c=80mmarrow_forward[20 Points] Use Method of Sections to draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the maximum bending moment that occurs in the span. 1.5 kN/m 4 m 2 m Carrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License