Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 42, Problem 14RQ
To determine
In Toyota hybrid CVT the part that effectively controls the over all gear ratio of the transaxle.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What is a suspension system.
Give at least 5 STATEMENT OF THE PROBLEM regarding to this
topic. (A statement of the problem is used in research work as a claim
that outlines the problem addressed by a study. The statement of the
problem briefly addresses the question: What is the problem that the
research will address?)
"Comparing ABS system to hydraulic break of a
vehicle"
Technician A says that limited- slip differential clutch packs are designed to slip when the vehicle turns a corner. Technician B says that a special additive is placed in the hypoid gear lubricant to promote clutch pack slippage on corners. Who is correct?
Chapter 42 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 42 - Although computers receive different information...Ch. 42 - What happens if the TCM determines that the...Ch. 42 - How can air pressure be used to check an...Ch. 42 - True or False? On most late-model EAT systems,...Ch. 42 - Prob. 5RQCh. 42 - List five things that could cause incorrect shift...Ch. 42 - Most late-model transmission control systems have...Ch. 42 - What inputs are of prime importance to a computer...Ch. 42 - What are the advantages of using electronic...Ch. 42 - Voltage generation devices are typically used to...
Ch. 42 - Which of the following is not a voltage-generating...Ch. 42 - True or False? The neutral safety switch and...Ch. 42 - A glitch appears in the waveform of a vehicle...Ch. 42 - Prob. 14RQCh. 42 - Which of the following would probably not be...Ch. 42 - Technician A says that some systems use a special...Ch. 42 - Technician A says that shift solenoids direct...Ch. 42 - Technician A says that throttle position is an...Ch. 42 - Technician A says that a faulty TP sensor can...Ch. 42 - Technician A says that some shift solenoids can be...Ch. 42 - An electronically controlled transmission has...Ch. 42 - While discussing transmission adaptive learning:...Ch. 42 - While discussing valve body assemblies in...Ch. 42 - A hot-wire MAF has low resistance across it when...Ch. 42 - While diagnosing the cause of TCC shudder:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing the CVT transaxie used in Toyota hybrid vehicles: Technician A says that the transaxie contains two electric motor/generators, a differential, and a simple planetary gearset. Technician B says that the planetary gearset adjusts the diameter of the pulleys to provide the various speed ratios. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardName the three main driveline components that are added to a RWD vehicle to make it a 4WD vehicle.arrow_forwardIdentify the function, nature and operation of the three system of G450 aircraft: 1. Hydraulic Landing Gear System of G450 2. Pneumatic Bleed Air System of G450. 3.Enviromental Control System of G450.arrow_forward
- A 3-degree difference in the SAI angle on each side of the front suspension may cause a FWD vehicle to have increased during hard acceleration.arrow_forwardTechnician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardA technician is working on a 2005 BMW 7 series.. The compressor is running all the time and the air is cold. The tech unplugs the wiring harness leading to the compressor, but it stays running. The technician recommends a new compressor as he suspects the clutch has melted. What is likely happening here? nothing. This compressor doesn’t have a clutch, only a pulley the clutch has melted due to a slipping belt only the hub needs replacement, the pulley is fine the compressor must be seized internally for this to happenarrow_forward
- While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?arrow_forwardWhile discussing HEVs: Technician A says that in a series hybrid, the engine is only used to power a generator to recharge the batteries. Technician B says that in a parallel hybrid, the engine and/or the battery can supply the power to move the vehicle. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says if the amber ABS warning light is on continuously, the ABS system is still operational but may not be operating at 100 percent efficiency. Technician B says ABS operation might be affected by improperly turning the drums and rotors. Who is correct? a. A only b. B only c. both A and B d. neither A nor Barrow_forward
- Technician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen replacing an accessory drive belt, all the following are important considerations EXCEPT: Select one: a. Pulley alignment b. Crankshaft to camshaft timing c. Belt dimensions d. Belt routingarrow_forwardWhile diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,