Fundamentals of Engineering Thermodynamics
8th Edition
ISBN: 9781118832301
Author: SHAPIRO
Publisher: JOHN WILEY+SONS,INC.-CONSIGNMENT
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4.12, Problem 6P
To determine
How many gallons of water wasted annually? and what is the mass of the wasted water in lb?.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
HW8
A shaft fitted with a flywheel rotates at 650 r.p.m. and drives a machine. The
torque of machine varies in a cyclic manner over a period of 2 revolutions. The
torque rises from 650 N-m to 2200 N-m uniformly during 110° and remains
constant for the following 270°. It then falls uniformly to 600 N-m during the next
100° and remains constant for the end cycle, the cycle being repeated thereafter.
Determine the power required to drive the machine and percentage fluctuation in
speed, if the driving torque applied to the shaft is constant and the mass of the
flywheel is 180 kg with radius of gyration of 35 cm.
HW9
units of h. show all work
4. Steam flows steadily through a turbine at a rate of 47,000 lbm/h, entering at 1000 psia
and 800°F and leaving at 6 psia as saturated vapor. If the power generated by the
turbine is 3.7 MW, determine the rate of heat loss from the steam.
Chapter 4 Solutions
Fundamentals of Engineering Thermodynamics
Ch. 4.12 - Prob. 1ECh. 4.12 - 2. When a drip coffeemaker on-off switch is turned...Ch. 4.12 - Prob. 3ECh. 4.12 - Prob. 4ECh. 4.12 - Prob. 5ECh. 4.12 - Prob. 6ECh. 4.12 - Prob. 7ECh. 4.12 - Prob. 8ECh. 4.12 - Prob. 9ECh. 4.12 - 10. How does the operator of a pumper-tanker fire...
Ch. 4.12 - Prob. 11ECh. 4.12 - Prob. 12ECh. 4.12 - 13. If the expansion valve of a refrigerator...Ch. 4.12 - Prob. 14ECh. 4.12 - Prob. 15ECh. 4.12 - Prob. 1CUCh. 4.12 - 6. Liquid flows at steady state at a rate of 2...Ch. 4.12 - 7. A flow idealized as a throttling process...Ch. 4.12 - 8. __________ is the work associated with the...Ch. 4.12 - 9. Steady flow devices that result in a drop in...Ch. 4.12 - 10. Steam enters a horizontal pipe operating at...Ch. 4.12 - Prob. 11CUCh. 4.12 - Prob. 12CUCh. 4.12 - Prob. 13CUCh. 4.12 - 14. _______ means all properties are unchanging in...Ch. 4.12 - Prob. 15CUCh. 4.12 - Prob. 16CUCh. 4.12 - 17. ________ operation involves state changes with...Ch. 4.12 - Prob. 18CUCh. 4.12 - 19. A horizontal air diffuser operates with inlet...Ch. 4.12 - 20. Mass flow rate for a flow modeled as...Ch. 4.12 - Prob. 21CUCh. 4.12 - Prob. 22CUCh. 4.12 - Prob. 23CUCh. 4.12 - 24. The mechanisms of energy transfer for a...Ch. 4.12 - 25. For one-dimensional flow, mass flow rate is...Ch. 4.12 - 26. At steady state, conservation of mass asserts...Ch. 4.12 - Prob. 27CUCh. 4.12 - Prob. 28CUCh. 4.12 - Prob. 29CUCh. 4.12 - Prob. 30CUCh. 4.12 - Prob. 31CUCh. 4.12 - Prob. 32CUCh. 4.12 - 33. A significant increase in pressure can be...Ch. 4.12 - Prob. 34CUCh. 4.12 - Prob. 35CUCh. 4.12 - Prob. 36CUCh. 4.12 - 37. Factors that may allow one to model a control...Ch. 4.12 - Prob. 38CUCh. 4.12 - Prob. 39CUCh. 4.12 - Prob. 40CUCh. 4.12 - Prob. 41CUCh. 4.12 - Prob. 42CUCh. 4.12 - Prob. 43CUCh. 4.12 - 44. The human body is an example of an integrated...Ch. 4.12 - Prob. 45CUCh. 4.12 - Prob. 46CUCh. 4.12 - 47. The thermodynamic performance of a device such...Ch. 4.12 - 48. For every control volume at steady state, the...Ch. 4.12 - Prob. 49CUCh. 4.12 - Prob. 50CUCh. 4.12 - Prob. 51CUCh. 4.12 - 52. At steady state, identical electric fans...Ch. 4.12 - Prob. 1PCh. 4.12 - Prob. 2PCh. 4.12 - 4.3 Steam enters a 1.6-cm-diameter pipe at 80 bar...Ch. 4.12 - Prob. 4PCh. 4.12 - Prob. 5PCh. 4.12 - Prob. 6PCh. 4.12 - 4.7 Figure P4.7 provides data for water entering...Ch. 4.12 - Prob. 8PCh. 4.12 - Prob. 9PCh. 4.12 - 4.10 Data are provided for the crude oil storage...Ch. 4.12 - 4.11 An 8-ft3 tank contains air at an initial...Ch. 4.12 - Prob. 12PCh. 4.12 - Prob. 13PCh. 4.12 - Prob. 14PCh. 4.12 - 4.15 Liquid water flows isothermally at 20°C...Ch. 4.12 - Prob. 16PCh. 4.12 - Prob. 17PCh. 4.12 - Prob. 18PCh. 4.12 - 4.19 As shown in Fig. P4.19, steam at 80 bar,...Ch. 4.12 - Prob. 20PCh. 4.12 - Prob. 21PCh. 4.12 - Prob. 22PCh. 4.12 - Prob. 23PCh. 4.12 - 4.24 Refrigerant 134a enters a horizontal pipe...Ch. 4.12 - 4.25 As shown in Fig. P4.25, air enters a pipe at...Ch. 4.12 - 4.26 Air enters a horizontal, constant-diameter...Ch. 4.12 - 4.27 Air at 600 kPa, 330 K enters a...Ch. 4.12 - 4.28 At steady state, air at 200 kPa, 325 K, and...Ch. 4.12 - 4.29 Refrigerant 134a flows at steady state...Ch. 4.12 - 4.30 As shown in Fig. P4.30, electronic components...Ch. 4.12 - 4.31 Steam enters a nozzle operating at steady...Ch. 4.12 - 4.32 Refrigerant 134a enters a well-insulated...Ch. 4.12 - 4.33 Air enters a nozzle operating at steady state...Ch. 4.12 - Prob. 34PCh. 4.12 - Prob. 35PCh. 4.12 - 4.36 Nitrogen, modeled as an ideal gas, flows at a...Ch. 4.12 - Prob. 37PCh. 4.12 - Prob. 38PCh. 4.12 - Prob. 39PCh. 4.12 - 4.40 Oxygen gas enters a well-insulated diffuser...Ch. 4.12 - Prob. 41PCh. 4.12 - 4.42 Steam enters a well-insulated turbine...Ch. 4.12 - Prob. 43PCh. 4.12 - 4.44 Air expands through a turbine operating at...Ch. 4.12 - Prob. 45PCh. 4.12 - 4.46 A well-insulated turbine operating at steady...Ch. 4.12 - Prob. 47PCh. 4.12 - Prob. 48PCh. 4.12 - Prob. 49PCh. 4.12 - Prob. 50PCh. 4.12 - Prob. 51PCh. 4.12 - Prob. 52PCh. 4.12 - Prob. 53PCh. 4.12 - 4.54 Nitrogen is compressed in an axial-flow...Ch. 4.12 - Prob. 55PCh. 4.12 - Prob. 56PCh. 4.12 - Prob. 57PCh. 4.12 - Prob. 58PCh. 4.12 - Prob. 59PCh. 4.12 - 4.60 Refrigerant 134a enters an insulated...Ch. 4.12 - Prob. 61PCh. 4.12 - Prob. 62PCh. 4.12 - 4.63 Air enters a compressor operating at steady...Ch. 4.12 - 4.64 Air enters a compressor operating at steady...Ch. 4.12 - Prob. 65PCh. 4.12 - Prob. 66PCh. 4.12 - Prob. 67PCh. 4.12 - 4.68 As shown in Fig. P4.68, a power washer used...Ch. 4.12 - Prob. 69PCh. 4.12 - Prob. 70PCh. 4.12 - Prob. 71PCh. 4.12 - 4.72 Oil enters a counterflow heat exchanger at...Ch. 4.12 - Prob. 73PCh. 4.12 - Prob. 74PCh. 4.12 - Prob. 75PCh. 4.12 - Prob. 76PCh. 4.12 - Prob. 77PCh. 4.12 - Prob. 78PCh. 4.12 - Prob. 79PCh. 4.12 - Prob. 80PCh. 4.12 - Prob. 83PCh. 4.12 - Prob. 84PCh. 4.12 - Prob. 85PCh. 4.12 - Prob. 86PCh. 4.12 - Prob. 87PCh. 4.12 - Prob. 88PCh. 4.12 - Prob. 89PCh. 4.12 - Prob. 90PCh. 4.12 - Prob. 91PCh. 4.12 - Prob. 92PCh. 4.12 - Prob. 93PCh. 4.12 - Prob. 94PCh. 4.12 - Prob. 95PCh. 4.12 - Prob. 96PCh. 4.12 - 4.97 As shown in Fig. P4.97, Refrigerant 22 enters...Ch. 4.12 - Prob. 98PCh. 4.12 - Prob. 99PCh. 4.12 - Prob. 100PCh. 4.12 - Prob. 101PCh. 4.12 - 4.102 Steady-state operating data for a simple...Ch. 4.12 - Prob. 103PCh. 4.12 - Prob. 104PCh. 4.12 - Prob. 105PCh. 4.12 - Prob. 106PCh. 4.12 - Prob. 107PCh. 4.12 - Prob. 108PCh. 4.12 - Prob. 109PCh. 4.12 - Prob. 110PCh. 4.12 - Prob. 111PCh. 4.12 - Prob. 112PCh. 4.12 - 4.113 An insulated, rigid tank whose volume is 10...Ch. 4.12 - Prob. 114PCh. 4.12 - Prob. 115PCh. 4.12 - Prob. 116PCh. 4.12 - Prob. 117PCh. 4.12 - Prob. 119PCh. 4.12 - Prob. 122PCh. 4.12 - Prob. 127PCh. 4.12 - Prob. 128PCh. 4.12 - 4.130 The procedure to inflate a hot-air balloon...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3. Water enters the constant 125-mm inside-diameter tubes of a boiler at 7.5 MPa and 60°C and leaves the tubes at 6 MPa and 500°C with a velocity of 75 m/s. Calculate the velocity of the water at the tube inlet and the inlet volume flow rate.arrow_forward2. A piston-cylinder device contains 2.4 kg of nitrogen initially at 120 kPa and 27°C. The nitrogen is now compressed slowly in a polytropic process during which PV1.3 = constant until the volume is reduced by one-half. Determine the work done and the heat transfer for this process.arrow_forward1. 1.25 m³ of saturated liquid water at 225°C is expanded isothermally in a closed system until its quality is 75 percent. Determine the total work produced by this expansion, in kJ.arrow_forward
- An undamped single-degree-of-freedom system is subjected to dynamic excitation as shown in Figure 1.• System properties: m = 1, c = 0, k = (6π)2.• Force excitation: p(t) = posin(ωt) where po = 9 and ω = 2π.• Initial conditions: u(t = 0) = 0 and ̇u(t = 0) = 0.Please, complete Parts (a) through (d) using any computational tool of your preference. The preferred toolis MATLAB. Print and turn in a single pdf file that will include your code/calculations and your plots.(a) Generate the solution using a linear interpolation of the load over each time step (note that hereyou can use the undamped coefficients). Plot the displacement response for the first 4 seconds andcompare to the exact closed form solution. Repeat using the following time step sizes, ∆t = 0.01,0.05, 0.15, 0.20 seconds. Include the closed form solution and the solutions for different ∆t values in asingle plot. Please, provide your observations by comparing the closed form solution with the solutionsderived using the four…arrow_forwardAssume multiple single degree of freedom systems with natural periods T ∈ [0.05, 2.00] seconds with in-crement of period dT = 0.05 seconds. Assume three cases of damping ratio: Case (A) ξ = 0%; Case (B)ξ = 2%; Case (C) ξ = 5%. The systems are initially at rest. Thus, the initial conditions are u(t = 0) = 0 anḋu(t = 0) = 0. The systems are subjected to the base acceleration that was provided in the ElCentro.txt file(i.e., first column). For the systems in Case (A), Case (B), and Case (C) and for each natural period computethe peak acceleration, peak velocity, and peak displacement responses to the given base excitation. Please,use the Newmark method for β = 1/4 (average acceleration) to compute the responses. Create threeplots with three lines in each plot. The first plot will have the peak accelerations in y-axis and the naturalperiod of the system in x-axis. The second plot will have the peak velocities in y-axis and the natural periodof the system in x-axis. The third plot will have…arrow_forwardBoth portions of the rod ABC are made of an aluminum for which E = 70 GPa. Based on the given information find: 1- deformation at A 2- stress in BC 3- Total strain 4- If v (Poisson ratio is 0.25, find the lateral deformation of AB Last 3 student ID+ 300 mm=L2 724 A P=Last 2 student ID+ 300 KN 24 24 Diameter Last 2 student ID+ 15 mm Last 3 student ID+ 500 mm=L1 724 C B 24 Q=Last 2 student ID+ 100 KN 24 Diameter Last 2 student ID+ 40 mmarrow_forward
- Q2Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 75 psi, determine (a) the largest load P that can be safely supported, (b) the corresponding shearing stress in the splice. น Last 1 student ID+5 inch=W =9 4 L=Last 1 student ID+8 inch =12 60° P'arrow_forwardQ4 The two solid shafts are connected by gears as shown and are made of a steel for which the allowable shearing stress is 7000 psi. Knowing the diameters of the two shafts are, respectively, dBC determine the largest torque Tc that can be applied at C. 4 and dEF dBC=Last 1 student ID+3 inch dEF=Last 1 student ID+1 inch 7 R=Last 1 Student ID+5 inch 9 R B Tc 2.5 in. E TF Harrow_forwardExperiment تكنولوجيا السيارات - Internal Forced convenction Heat transfer Air Flow through Rectangular Duct. objective: Study the convection heat transfer of air flow through rectangular duct. Valve Th Top Dead Centre Exhaust Valve Class CP. N; ~ RIVavg Ti K 2.11 Te To 18.8 21.3 45.8 Nath Ne Pre Calculations:. Q = m cp (Te-Ti) m: Varg Ac Acca*b Q=hexp As (Ts-Tm) 2 2.61 18.5 20.846.3 Tm = Te-Ti = 25 AS-PL = (a+b)*2*L Nu exp= Re-Vavy D heep Dh k 2ab a+b Nu Dh the- (TS-Tm) Ts. Tmy Name / Nu exp Naxe بب ارتدان العشريarrow_forward
- Procedure:1- Cartesian system, 2D3D,type of support2- Free body diagram3 - Find the support reactions4- If you find a negativenumber then flip the force5- Find the internal force3D∑Fx=0∑Fy=0∑Fz=0∑Mx=0∑My=0\Sigma Mz=02D\Sigma Fx=0\Sigma Fy=0\Sigma Mz=05- Use method of sectionand cut the elementwhere you want to findarrow_forwardProcedure:1- Cartesian system, 2D3D,type of support2- Free body diagram3 - Find the support reactions4- If you find a negativenumber then flip the force5- Find the internal force3D∑Fx=0∑Fy=0∑Fz=0∑Mx=0∑My=0\Sigma Mz=02D\Sigma Fx=0\Sigma Fy=0\Sigma Mz=05- Use method of sectionand cut the elementwhere you want to findthe internal force andkeep either side of thearrow_forwardProcedure: 1- Cartesian system, 2D3D, type of support 2- Free body diagram 3 - Find the support reactions 4- If you find a negative number then flip the force 5- Find the internal force 3D ∑Fx=0 ∑Fy=0 ∑Fz=0 ∑Mx=0 ∑My=0 ΣMz=0 2D ΣFx=0 ΣFy=0 ΣMz=0 5- Use method of section and cut the element where you want to find the internal force and keep either side of thearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY