Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.

Question

Want to see more full solutions like this?

Answer 1

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

3. An engine has three cylinders spaced at 120° to each other. The crank torque diagram can be simplified to a triangle having the following values: Angle 0° Torque (Nm) 0 (a) What is the mean torque? 60° 4500 180° 180° to 360° 0 0 (b) What moment of inertia of flywheel is required to keep the speed to within 180 ± 3 rpm? (c) If one cylinder of the engine is made inoperative and it is assumed that the torque for this cylinder is zero for all crank angles, determine the fluctuation in speed at 180rpm for the same flywheel. (a) 3375 Nm (b) 50kgm (c) ±21 rpm

Prob 5. Determine the largest load P that can be applied to the frame without causing either the average normal stress or the average shear stress at section a-a to exceed o-150 MPa and 1-60 MPa, respectively. Member CB has a square cross section of 25 mm on each side. 2 m FAC 1.5 m Fac

Derive the component transformation equations for tensors shown below where [C] = [BA] is the DCM (direction cosine matrix) from frame A to B. ^B [T] = [C]^A [T] [C]^T

Answer 2

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Textbook Question

Answer 6

Textbook Question

Answer 7

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 8

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer 12

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 13

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 14

Ch. 41 - Before installing a gauge on the high-pressure...Ch. 41 - Capacitors should be shorted with a(n)...Ch. 41 - The high- and low-side pressures on an operating...Ch. 41 - Why do most air-conditioning systems not need a...Ch. 41 - A typical standard-efficiency evaporator under...Ch. 41 - The typical temperature difference between the...Ch. 41 - When the ambient outside air temperature isand the...Ch. 41 - When the outside ambient air temperature is 90F,...Ch. 41 - If a condensing pressure is 260 psig for R-22,...Ch. 41 - How is high efficiency accomplished in an...

Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.

Videos

Answer to Problem 1RQ

Explanation of Solution

Want to see more full solutions like this?

Chapter 41 Solutions