To determine Calculate the power delivered by the dependent voltage source in the given circuit using PSPICE. Explanation The given circuit is redrawn as shown in Figure 1. From Figure 1, the current i σ is calculated by using Kirchhoff’s current law at node a . i σ + i 1 = i 2 i σ = i 2 − i 1 (1) Apply Kirchhoff’s voltage law for Loop 1 in Figure 1. 10 i 1 + 100 ( i 1 − i 2 ) = 160 10 i 1 + 100 i 1 − 100 i 2 = 160 110 i 1 − 100 i 2 = 160 11 i 1 − 10 i 2 = 16 (2) Apply Kirchhoff’s voltage law for Loop 2 in Figure 1. 100 ( i 2 − i 1 ) + 30 i 2 + 150 i σ + 20 i 2 = 0 100 i 2 − 100 i 1 + 30 i 2 + 150 i σ + 20 i 2 = 0 (3) Substitute equation (1) in equation (3). 100 i 2 − 100 i 1 + 30 i 2 + 150 ( i 2 − i 1 ) + 20 i 2 = 0 150 i 2 − 100 i 1 + 150 i 2 − 150 i 1 = 0 − 250 i 1 + 300 i 2 = 0 − 25 i 1 + 30 i 2 = 0 Rearrange the equation as follows, 25 i 1 = 30 i 2 i 1 = 30 25 i 2 i 1 = 1.2 i 2 (4) Substitute equation (4) in equation (2). 11 ( 1

11th Edition

ISBN: 8220106795262

Author: Riedel

Publisher: YUZU

See similar textbooks

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysi…

Videos

Question

Chapter 4, Problem 38P

To determine

Calculate the power delivered by the dependent voltage source in the given circuit using PSPICE.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 37P

Chapter 4, Problem 39P

Students have asked these similar questions

Open plc - ladder logic To control traffic, we have red lights to stop cars and green lights to initiate entry/exit. If a car is in the lane, then the red lights turn ON. If no cars are in the lane, then the green lights turn ON. Upon turning ON the main switch button, the main switch indicator should turn ON and the system should start with green lights ON and red lights OFF?

3-4) 3.4-2 Signals g₁(t) = 104П(104) and g2(t) = 8(t) are applied at the inputs of the ideal low-pass filters H₁(f)=(f/20,000) and H2(f) = П(f/10,000) (Fig. P3.4-2). The outputs y₁ (t) and y2(t) of these filters are multiplied to obtain the signal y(t) = y1 (1)y2(t). (a) Sketch G1(f) and G2(f). (b) Sketch H₁(f) and H₂(f). (c) Sketch Y₁ (f) and Y2(f). (d) Find the bandwidths of y₁ (t), y2(t), and y(t). 8₁ (1) H₁(f) y, (t) y(t) = y₁ (1) y2 (1) 82(1) ½⁄2 (1) H₂(f)

solve the differential equation y'' -2y'-3y=x³e^5x cos(3x) Don't use AI,I need it handwritten

Chapter 4 Solutions

EBK ELECTRIC CIRCUITS

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.