AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 5MC
A poorly adjusted shift linkage can cause which of the following problems?
a. Gear clash
b. Hard shifting
c. The gear to jump out
d. All of the above
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A poorly adjusted shift linkage can cause whichof the following problems?a. Gear clashb. Hard shiftingc. The gear to jump outd. All of the above
Technician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?
Technician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?
Technician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?
Technician A says that a faulty TP sensor can cause delayed shifts. Technician B says that delayed shifts can be caused by an open shift solenoid. Who is correct?
Technician A says that some shift solenoids can be activated by providing a ground for the solenoid. Technician B says that some shift solenoids can be activated by…
What can too much clutch pedal free play cause?
a.hard gear shifting
b.fast release bearing wear
c.release fork wear
d.clutch slipping
Chapter 39 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When discussing the various gear positions of a transfer case, Technician A says that when the transfer case is in low, the overall gear ratio is numerically increased. Technician B says that when the transfer case is in the high position, the vehicle operates in an overdrive mode due to the decrease in torque multiplication. Who is correct?arrow_forwardWhat is the correct sequence for adjusting alignmentangles during a four-wheel alignment?arrow_forwardWhat inputs are of prime importance to a computer in deciding when to shift gears?arrow_forward
- While discussing shift mechanisms: Technician A says that the interlock notches hold the transmission in the selected gear. Technician B says that the detent notches prevent the selection of more than one gear during operation. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following gear ratios indicates an over-drive condition? a. 2.15:1 b. 1:1 c. 0.85:1 d. None of the abovearrow_forwardWhen discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
- briefly define the following: 1. airborne transmission 2. common vehicle transmission 3. contact transmissionarrow_forwardPinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardTechnician A says that some systems use a special modulated shift control solenoid. Technician B says that some systems use a special modulated converter clutch control solenoid. Who is correct?arrow_forward
- Technician A says that when a car is moving straight ahead, all differential gears rotate as a unit. Technician B says that when a car is turning a corner, the inside differential side gear rotates slowly on the pinion, causing the outside side gear to rotate faster. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardPlease help with homework questionarrow_forwardWhich of the following gear ratios indicates an overdrivecondition?a. 2.15 : 1b. 1 : 1c. 0.85 : 1d. None of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License