Concept explainers
Determine the specific volume of superheated water vapor at 15 MPa and 350°C using (a) the ideal-gas equation, (b) the generalized compressibility chart, and (c) the steam tables. Also determine the error involved in the first two cases.
(a)

The specific volume of superheated water vapour based on the ideal gas equation.
The error involved.
Answer to Problem 82P
The specific volume of superheated water vapour based on the ideal gas equation is
The error involved is
Explanation of Solution
Write the equation of specific volume of superheated water using ideal gas equation of state.
Here, gas constant is R, pressure and temperature of R-134a are P and T respectively.
Calculate the percentage of error involved.
Here, specific volume at pressure and temperature of 15 MPa and
Conclusion:
Refer to Table A-1, obtain the gas constant, R of water as
Substitute
Thus, the specific volume of superheated water vapour based on the ideal gas equation is
Refer to Table A-6, obtain the value of
Substitute
Thus, the error involved is
(b)

The specific volume of superheated water vapour based on the generalized compressibility chart.
The error involved.
Answer to Problem 82P
The specific volume of superheated water vapour based on the generalized compressibility chart is
The error involved is
Explanation of Solution
Calculate the reduced pressure.
Here, pressure of superheated water vapour is P and critical pressure is
Calculate the reduced temperature.
Here, temperature of superheated water vapor is T and critical temperature is
Calculate the specific volume of superheated water vapour based on the generalized compressibility chart.
Here, the specific volume at ideal condition is
Conclusion:
Refer to Table A-1, obtain the critical pressure and critical temperature of water.
Substitute 22.06 MPa for
Substitute 647.1 K for
Refer to figure A-15, “The compressibility chart”, obtain the compressibility factor, Z by reading the calculated reduced pressure and reduced temperature as 0.65.
Substitute 0.65 for Z and
Thus, the specific volume of superheated water vapour based on the generalized compressibility chart is
Substitute
Thus, the error involved is
(c)

The specific volume of superheated water vapour based on the data from tables.
Answer to Problem 82P
The specific volume of superheated water vapour based on the data from table is
Explanation of Solution
Refer to Table A-6, obtain the specific volume at pressure and temperature of 15 MPa and
Thus, the specific volume of superheated water vapour based on data from steam tables is
Want to see more full solutions like this?
Chapter 3 Solutions
THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I
- 1. The rotating steel shaft is simply supported by bearings at points of B and C, and is driven by a spur gear at D, which has a 6-in pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA =3000 lbĘ in. The shaft is machined from steel with Sy=60kpsi and Sut=80 kpsi. (1) Draw a shear force diagram and a bending moment diagram by F. According to your analysis, where is the point of interest to evaluate the safety factor among A, B, C, and D? Describe the reason. (Hint: To find F, the torque Tд is generated by the tangential force of F (i.e. Ftangential-Fcos20°) When n=2.5, K=1.8, and K₁ =1.3, determine the diameter of the shaft based on (2) static analysis using DE theory (note that fatigue stress concentration factors need to be used for this question because the loading condition is fatigue) and (3) a fatigue analysis using modified Goodman. Note) A standard diameter is not required for the questions. 10 in Darrow_forward3 N2=28 P(diametral pitch)=8 for all gears Coupled to 25 hp motor N3=34 Full depth spur gears with pressure angle=20° N₂=2000 rpm (1) Compute the circular pitch, the center-to-center distance, and base circle radii. (2) Draw the free body diagram of gear 3 and show all the forces and the torque. (3) In mounting gears, the center-to-center distance was reduced by 0.1 inch. Calculate the new values of center-to-center distance, pressure angle, base circle radii, and pitch circle diameters. (4)What is the new tangential and radial forces for gear 3? (5) Under the new center to center distance, is the contact ratio (mc) increasing or decreasing?arrow_forward2. A flat belt drive consists of two 4-ft diameter cast-iron pulleys spaced 16 ft apart. A power of 60 hp is transmitted by a pulley whose speed is 380 rev/min. Use a service factor (Ks) pf 1.1 and a design factor 1.0. The width of the polyamide A-3 belt is 6 in. Use CD=1. Answer the following questions. (1) What is the total length of the belt according to the given geometry? (2) Find the centrifugal force (Fc) applied to the belt. (3) What is the transmitted torque through the pulley system given 60hp? (4) Using the allowable tension, find the force (F₁) on the tight side. What is the tension at the loose side (F2) and the initial tension (F.)? (5) Using the forces, estimate the developed friction coefficient (f) (6) Based on the forces and the given rotational speed, rate the pulley set. In other words, what is the horse power that can be transmitted by the pulley system? (7) To reduce the applied tension on the tight side, the friction coefficient is increased to 0.75. Find out the…arrow_forward
- The tooth numbers for the gear train illustrated are N₂ = 24, N3 = 18, №4 = 30, №6 = 36, and N₁ = 54. Gear 7 is fixed. If shaft b is turned through 5 revolutions, how many turns will shaft a make? a 5 [6] barrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forwardCE-112 please solve this problem step by step and give me the correct answerarrow_forward
- CE-112 solve this problem step by step and give me the correct answer pleasearrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forwardPlease do not use any AI tools to solve this question. I need a fully manual, step-by-step solution with clear explanations, as if it were done by a human tutor. No AI-generated responses, please.arrow_forward
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
