EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 35, Problem 17QLP
Why are the words “accuracy” and “precision” often incorrectly interchanged?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Which is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?
With appropriate precision (significant digits), what is 2 + 2.1?.
Indicate the following technical tolerance requirements in Fig.3.
a) The diameter of the middle cylinder is Odh7, use Envelope
requirement;
b) Cylindricity tolerance of d is 0.009mm, straightness of axis of od
is $0.012mm;
c) Total run-out tolerance of right end surfaces related to axis of Pd
is 0.01 mm;
d) The surface of od cylinder is obtained by the method of removing
material, and the maximum allowable value of Rz is 0.4µm. All
surfaces are obtained by the method of removing material, and all
the roughness Ra allowable value is 6.4 pm.
Chapter 35 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 35 - What is metrology?Ch. 35 - Explain how a meter is defined and measured.Ch. 35 - Explain what is meant by standards for...Ch. 35 - What is the basic difference between...Ch. 35 - What is meant by comparative length measurement?Ch. 35 - Explain how flatness is measured. What is an...Ch. 35 - Describe the principle of an optical comparator.Ch. 35 - Why have coordinate measuring machines...Ch. 35 - What is the difference between a plug gage and...Ch. 35 - What are dimensional tolerances? Why is their...
Ch. 35 - Prob. 11RQCh. 35 - Explain the difference between tolerance and...Ch. 35 - What is the difference between bilateral and...Ch. 35 - How is straightness measured?Ch. 35 - When is a clearance fit desirable? An interference...Ch. 35 - What factors contribute to deviations in the...Ch. 35 - Why are the words accuracy and precision...Ch. 35 - Prob. 18QLPCh. 35 - Prob. 19QLPCh. 35 - Prob. 20QLPCh. 35 - Dimensional tolerances for nonmetallic parts...Ch. 35 - Prob. 22QLPCh. 35 - Review Fig. 35.20, and comment on the range...Ch. 35 - In the game of darts, is it better to be accurate...Ch. 35 - What are the advantages and limitations of GO...Ch. 35 - Comment on your observations regarding Fig. 35.19.Ch. 35 - What are gage blocks? Explain three methods...Ch. 35 - Why is it important to control temperature during...Ch. 35 - Describe the characteristics of electronic gages.Ch. 35 - What method would you use to measure the...Ch. 35 - Prob. 31QLPCh. 35 - Review Fig. 35.21 and give reasons that there is a...Ch. 35 - Assume that a steel rule expands by 0.07% due to...Ch. 35 - If the same steel rule as in Problem 35.33 is used...Ch. 35 - A shaft must meet a design requirement of being at...Ch. 35 - Describe your thoughts on the merits and...Ch. 35 - Take an ordinary vernier micrometer (see Fig....Ch. 35 - Obtain a digital micrometer and a steel ball of,...Ch. 35 - Prob. 41SDPCh. 35 - Prob. 42SDPCh. 35 - Inspect various parts and components in...Ch. 35 - Prob. 45SDPCh. 35 - Prob. 46SDPCh. 35 - Prob. 47SDPCh. 35 - Conduct an Internet search, and make a list of...Ch. 35 - Prob. 49SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Give explanation of this answer alsoarrow_forwardAn angle of 41° is found when a sine bar of the length 190.5 mm is used during the precise angle measurement of a workpiece in a workshop. Find the height of the Slip gauge setting observed during the measurement process in mm%3D (Enter at least 4 digits after decimal points)arrow_forwardQ1. (Unit 4) The tensile strength of a metal part is normally distributed with mean 40 lb and standard deviation 8 lb. If 50,000 parts are produced, a) how many would fail to meet a minimum specification limit of 34 lb tensile strength? b) How many would have a tensile strength in excess of 48 lb?arrow_forward
- Research and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Discuss a specific feature in a specific product/design case where calling out this geometric tolerance would be relevant for performance, assembly, or general operation.arrow_forwardWhat are three commonly used test to measure the hardness related properties of materials?arrow_forwardI need help with number 15. How much would the tolerance be? And where would the Level part go? I've attached the question and my sketch for reference.arrow_forward
- Which order arranges the following manufacturing processes from the least precise to the most precise tolerance limits?POSSIBLE ANSWERS1 . Turning, grinding, casting2 . Casting, turning, grinding3 . Casting. grinding, turning4 . Turning, casting, grindingarrow_forwardWould a flatness tolerance of .010 for the part in the drawing below be appropriate? Yes O No 3.000 1.000 XXX = +.005 ANGLES ± 1°arrow_forwardTooling Design ☐ Device need to be placed by Pick and place with accuracy of +/- 50um into nest. • Device size = 1.0 xo.8xo.6mm (Tolerance = +/-0.05mm all sides) 0.8 mm Y mm Z mm Y= Z= _mm, Explain mm, Explainarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY