Concept explainers
Write down the chemical formulae for the combustion of the alkanes in Table 3.2 with n = 2 to n = 8. Determine the mass of CO2 produced per megajoule of energy.
Provide the chemical formula for the combustion of alkanes with
Calculate the mass of
Explanation of Solution
Calculation:
Provide the general equation for the combustion of alkanes as shown below.
Refer to Table 3.2 “Alkane series of hydrocarbons with the formula
Take the name, formula, and the heat combustion values for each alkanes.
Provide the chemical formula for the combustion of alkanes with
n | Name | Formula | Combustion of alkanes | Moles | Moles of alkane |
2 | Ethane | 4 | 2 | ||
3 | Propane | 3 | 1 | ||
4 | Butane | 8 | 2 | ||
5 | Pentane | 5 | 1 | ||
6 | Hexane | 12 | 2 | ||
7 | Heptane | 7 | 7 | ||
8 | Octane | 16 | 2 |
The molecular mass of
Calculate the mass of
Provide the mass of
n | M (alkane) | Heat of combustion (MJ/kg) | |||
2 | 2 | 30 | 2.93 | 51.9 | 0.0565 |
3 | 3 | 44 | 3 | 50.3 | 0.0596 |
4 | 4 | 58 | 3.03 | 49.5 | 0.0612 |
5 | 5 | 72 | 3.06 | 48.7 | 0.0628 |
6 | 6 | 86 | 3.07 | 48.1 | 0.0638 |
7 | 7 | 100 | 3.08 | 48.1 | 0.0640 |
8 | 8 | 114 | 3.09 | 46.8 | 0.0660 |
Want to see more full solutions like this?
Chapter 3 Solutions
MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
Additional Engineering Textbook Solutions
Elementary Surveying: An Introduction To Geomatics (15th Edition)
Thermodynamics: An Engineering Approach
Modern Database Management
Starting Out with C++ from Control Structures to Objects (9th Edition)
Database Concepts (8th Edition)
HEAT+MASS TRANSFER:FUND.+APPL.
- Q.2 a. Determine the net area along route ABCDEF for C15x33.9(Ag=10in2) as shown in Fig. Holes are for %- in bolts. b. compute the design strength if A36 is used 0.650 in 14in 3in 0.400 in 9 in C15 x 33.9 3 in 14 in 2 in 0.650 in (b) (c) 141 3+2-040arrow_forwarda. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in -0.220 in 3 in HE -by-3.99 in 3 in 3 in DO 2 in 2 inarrow_forwarda. Determine the net area of the W12x16(Ag=4.71in2) shown in Fig. Assuming that the holes are for 1-in bolts. b. compute the design strength if A36 is used W12 x 16 d-12.00 in 4-0.220 in 3 in 3 in BO HO by-3.99 in 3 in 3 in DO E 2 in 2 inarrow_forward
- 止 Q.1 Using the lightest W section shape to design the compression member AB shown in Fig. below, the concentrated service dead load and live load is PD-40kips and PL 150kips respectively. The beams and columns are oriented about the major axis and the columns are braced at each story level for out-of-plan buckling. Assume that the same section is used for columns. Use Fy-50 ksi. 32456 Aarrow_forward02. Design a W shape beam is used to support the loads for plastered floor, shown in Figure. Lateral bracing is supplied only at the ends. Depend LRFD and Steel Fy=50ksi. Note: The solution includes compute C, Check deflection at center of beam as well as shear capacity) B P10.5 P=140 W C Hing Hing 159 A 15.ftarrow_forwardحصنبتؤح٩ص٧٢٧قزرزكض٤arrow_forward
- مستبنؤدضح٧٢٧قنرةظسarrow_forwardHajfiwkkhdarrow_forwardس (١) الشكل المرفق لقطعة أرض مستطيلة بعدها بالاتجاه الأفقي ١٢ متر ماهو مقياس الرسم لهذة الخارطة وماهو البعد بالاتجاه العمودي على الأرض . س (۲) ماهي انواع المساحة من حيث الدقة . س ۳) طريق يحتوي على ثلاث محطات المسافات بينهم متساوية المحطة الأولى A = 233457.8 متر المحطة الثانية 8 = 23.6+278 متر ماهي المحطة الاخيرة ) 12 marrow_forward
- Solid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning