PEARSON ETEXT ENGINEERING MECH & STATS
PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 3, Problem 1FP

The crate has a weight of 550 lb. Determine the force in each supporting cable.

Chapter 3, Problem 1FP, The crate has a weight of 550 lb. Determine the force in each supporting cable.

Expert Solution & Answer
Check Mark
To determine

The force in each supporting cable.

Answer to Problem 1FP

The force in cable AB (FAB) is 478lb_.

The force in cable AC (FAC) is 518lb_.

Explanation of Solution

Given information:

The weight of a crate is (W) is 550 lb.

Show the free body diagram of the cable as in Figure 1.

PEARSON ETEXT ENGINEERING MECH & STATS, Chapter 3, Problem 1FP

Determine the force of the members AB and AC by applying the Equation of equilibrium.

Along horizontal direction:

Fx=0FACcosθACFABcosθAB=0 (I)

Here, the angle of force AC is θAC and the angle of force AB is θAB.

Along the vertical direction:

Fy=0FACsinθAC+FABsinθABW=0 (II)

Conclusion:

Substitute (45) for cosθAC and 30° for θAB in Equation (I).

FAC(45)FABcos30°=0FAC(45)=0.866FABFAC=(0.866×54)FABFAC=1.0825FAB (III)

Substitute 1.0825FAB for FAC, (35) for sinθAC and 30° for θAB, 550 lb for W in Equation (II).

(1.0825FAB)(35)+FABsin30°550=00.649FAB+0.5FAB=5501.149FAB=550FAB=5501.149

FAB=478lb

Thus, the force in cable AB (FAB) is 478lb_.

Substitute 478 lb for FAB in Equation (III).

FAC=1.0825×478=518lb

Thus, the force in cable AC (FAC) is 518lb_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
04:29
Students have asked these similar questions
Complete the following problems. Show your work/calculations, save as.pdf and upload to the assignment in Blackboard. missing information to present a completed program. (Hint: You may have to look up geometry for the center drill and standard 0.5000 in twist drill to know the required depth to drill). 1. What are the x and y dimensions for the center position of holes 1,2, and 3 in the part shown in Figure 26.2 (below)? 6.0000 Zero reference point 7118 1.0005 1.0000 1.252 Bore 6.0000 .7118 Cbore 0.2180 deep (3 holes) 2.6563 1.9445 Figure 26.2 026022 (8lot and Drill Part) (Setup Instructions--- (UNITS: Inches (WORKPIECE NAT'L SAE 1020 STEEL (Workpiece: 3.25 x 2.00 x0.75 in. Plate (PRZ Location 054: ' XY 0.0 - Upper Left of Fixture TOP OF PART 2-0 (Tool List ( T02 0.500 IN 4 FLUTE FLAT END MILL #4 CENTER DRILL Dashed line indicates- corner of original stock ( T04 T02 3.000 diam. slot 0.3000 deep. 0.3000 wide Intended toolpath-tangent- arc entry and exit sized to programmer's judgment…
A program to make the part depicted in Figure 26.A has been created, presented in figure 26.B, but some information still needs to be filled in. Compute the tool locations, depths, and other missing information to present a completed program. (Hint: You may have to look up geometry for the center drill and standard 0.5000 in twist drill to know the required depth to drill).
We consider a laminar flow induced by an impulsively started infinite flat plate. The y-axis is normal to the plate. The x- and z-axes form a plane parallel to the plate. The plate is defined by y = 0. For time t <0, the plate and the flow are at rest. For t≥0, the velocity of the plate is parallel to the 2-coordinate; its value is constant and equal to uw. At infinity, the flow is at rest. The flow induced by the motion of the plate is independent of z. (a) From the continuity equation, show that v=0 everywhere in the flow and the resulting momentum equation is მu Ət Note that this equation has the form of a diffusion equation (the same form as the heat equation). (b) We introduce the new variables T, Y and U such that T=kt, Y=k/2y, U = u where k is an arbitrary constant. In the new system of variables, the solution is U(Y,T). The solution U(Y,T) is expressed by a function of Y and T and the solution u(y, t) is expressed by a function of y and t. Show that the functions are identical.…

Chapter 3 Solutions

PEARSON ETEXT ENGINEERING MECH & STATS

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Engineering Basics - Statics & Forces in Equilibrium; Author: Solid Solutions - Professional Design Solutions;https://www.youtube.com/watch?v=dQBvQ2hJZFg;License: Standard YouTube License, CC-BY