Industrial Motor Control
7th Edition
ISBN: 9781133691808
Author: Stephen Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 29, Problem 1RQ
To determine
The way in which the direction of the rotation of the three phase motor can be changed.
Expert Solution & Answer
Explanation of Solution
The direction of the rotation of three phase motor is changed by changing the leads connection. Consider the Figure 29-1 of the text book as it has T leads, when the leads 1 and 3 are interchanged then the motor starts to rotate in the opposite direction.
The change in terminals changes the flow of current and it changes the direction of the rotation of the field thus, it changes the direction of rotation of the motor.
The rotation of the motor is also changed by the help of the reverse starter as shown in Figure 29-2 in the text book.
Thus, the direction of the rotation of the three phase is obtained by the change inn terminals.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
The airplane weighs 144100 lbs and flies at constant speed
and trajectory given by 0 on the figure. The plane
experiences a drag force of 73620 lbs.
a.) If = 11.3°, determine the thrust and lift forces
required to maintain this speed and trajectory.
b.) Next consider the case where is unknown, but it is
known that the lift force is equal to 7.8 times the quantity
(Fthrust Fdrag). Compute the resulting trajectory angle
-
and the lift force in this case. Use the same values for the
weight and drag forces as you used for part a.
Уллу
Fdrag
10.
Ө
Fthrust
cc 10
2013 Michael Swanbom
BY NC SA
Flift
Fweight
The lift force acts in the y' direction. The weight acts in the
negative y direction. The thrust and drag forces act in the
positive and negative x' directions respectively.
Part (a)
The thrust force is equal to
lbs.
The lift force is equal to
Part (b)
The trajectory angle is equal to
deg.
The lift force is equal to
lbs.
lbs.
The hoist consists of a single rope and an arrangement of
frictionless pulleys as shown. If the angle 0 = 59°, determine
the force that must be applied to the rope, Frope, to lift a
load of 4.4 kN. The three-pulley and hook assembly at the
center of the system has a mass of 22.5 kg with a center of
mass that lies on the line of action of the force applied to the
hook.
e
ΘΕ
B
CC 10
BY NC SA
2013 Michael Swanbom
Fhook
Note the figure may not be to scale.
Frope
=
KN
HO
Frope
Determine the tension developed in cables AB and AC
and the force developed along strut AD for equilibrium of
the 400-lb crate.
x.
5.5 ft
C
2 ft
Z
2 ft
D
6 ft
B
4 ft
A
2.5 ft
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A block of mass m hangs from the end of bar AB that is 7.2 meters long and connected to the wall in the xz plane. The bar is supported at A by a ball joint such that it carries only a compressive force along its axis. The bar is supported at end B by cables BD and BC that connect to the xz plane at points C and D respectively with coordinates given in the figure. Cable BD is elastic and can be modeled as a linear spring with a spring constant k = 400 N/m and unstretched length of 6.34 meters. Determine the mass m, the compressive force in beam AB and the tension force in cable BC. Z D (c, 0, d) C (a, 0, b), A e B y f m BY NC SA x 2016 Eric Davishahl Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 8.1 m b 3.3 m C 2.7 m d 3.9 m e 2 m f 5.4 m The mass of the block is The compressive force in bar AB is The tension in cable S is N. kg.arrow_forwardTwo squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.2 lb. The squirrel at B found less food this season and has a weight of 0.8 lb. The angles 0 and > are equal to 50° and 60° respectively. Determine the tension force in each of the rope segments (T₁ in segment, T₂ in segment Я, and T3 in segment DD) as well as the angle a in degrees. Ө A α B Note the figure may not be to scale. T₁ = lb lb T2 T3 = = lb απ deg A BY NC SA 2013 Michael Swanbomarrow_forwardEach cord can sustain a maximum tension of 500 N. Determine the largest mass of pipe that can be supported. B 60° A E Harrow_forward
- 2. Link BD consists of a single bar 1 in. wide and 0.5 in. thick. Knowing that each pin has a in. diameter, determine (a) the maximum value of the normal stress in link BD and the bearing stress in link BD if 0 = 0, (b) the maximum value of the normal stress in link BD if 0 = 90. -6 in.- 12 in. 30° D 4 kipsarrow_forwardIn the image is a right rectangular pyramid of total mass m. Note the location of point Q. Determine the inertia dyadic for the pyramid P, relative to point Q for e hat unit vectors.arrow_forwardauto controlsarrow_forward
- auto controlsarrow_forwardA 4 ft 300 Ib 1000 Ib.ft 350 Ib C 2 ft 3. 45° 250 Ib B. 3ft B 25ft 200 Ib 150 Ib Replace the force system acting on the frame shown in the figure by a resultant force (magnitude and direction), and specify where its line of action intersects member (AB), measured from point (A).arrow_forwardCan you research the standard percentage of Steam Quality in:(1.) Boiler - leaving boilerBoiler -> Out(2.) Condenser - coming in condenser In -> CondenserProvide reference Also define: steam quality, its purpose and importancearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning