Explanation Write the energy balance for the system. E ˙ in − E ˙ out = ( d E d t ) system (I) Here, rate of input energy is E ˙ in , rate of energy output is E ˙ out , and rate of change of system energy is ( d E / d t ) system . Consider that the gasoline operates at steady condition and neglect the changes in internal, potential, and kinetic energies. E ˙ in − E ˙ out = 0 (II) Difference in energy rate in and out is equal to the rate of net energy transfer by heat, work, and mass. Rewrite energy difference in terms of rate of work, heat and mass. W ˙ in + m ˙ ( P v ) in − m ˙ ( P v ) out = 0 W ˙ in = m ˙ [ ( P v ) out − ( P v ) in ] = m ˙ [ ( P ) out − ( P ) in ] v (III) Here, rate of power input is W ˙ in , mass flow rate is m ˙ , inlet pressure is ( P ) in , outlet pressure is ( P ) out , and volume of air is v

8th Edition

ISBN: 9780100257054

Author: CENGEL

Publisher: YUZU

See similar textbooks

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Videos

Question

Chapter 2.8, Problem 50P

To determine

The maximum volumetric flow rate of air.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 2.8, Problem 49P

Chapter 2.8, Problem 51P

Students have asked these similar questions

1. A 40 lb. force is applied at point E. There are pins at A, B, C, D, and F and a roller at A. a. Draw a FBD of member EFC showing all the known and unknown forces acting on it. b. Draw a FBD of member ABF showing all the known and unknown forces acting on it. c. Draw a FBD of member BCD showing all the known and unknown forces acting on it. d. Draw a FBD of the entire assembly ADE showing all the known and unknown forces acting on it. e. Determine the reactions at A and D. f. Determine the magnitude of the pin reaction at C. 40 lbs. B A 6 in. 4 in. D F -5 in.4 in 4.

A crude oil of specific gravity0.85 flows upward at a volumetric rate of flow of 70litres per second through a vertical venturimeter,with an inlet diameter of 250 mm and a throat diameter of 150mm. The coefficient of discharge of venturimeter is 0.96. The vertical differences betwecen the pressure toppings is 350mm. i) Draw a well labeled diagram to represent the above in formation i) If the two pressure gauges are connected at the tapings such that they are positioned at the levels of their corresponding tapping points, determine the difference of readings in N/CM² of the two pressure gauges ii) If a mercury differential manometer is connected in place of pressure gauges, to the tappings such that the connecting tube up to mercury are filled with oil determine the difference in the level of mercury column.

Can you solve it analytically using laplace transforms and with Matlab code as well please. Thank You

Chapter 2 Solutions

EBK THERMODYNAMICS: AN ENGINEERING APPR

Ch. 2.8 - What is total energy? Identify the different forms...Ch. 2.8 - List the forms of energy that contribute to the...Ch. 2.8 - How are heat, internal energy, and thermal energy...Ch. 2.8 - What is mechanical energy? How does it differ from...Ch. 2.8 - Natural gas, which is mostly methane CH4, is a...Ch. 2.8 - Portable electric heaters are commonly used to...Ch. 2.8 - Prob. 7P Ch. 2.8 - Prob. 8P Ch. 2.8 - 2–9E Calculate the total potential energy, in Btu,...Ch. 2.8 - Prob. 10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.