THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I
THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I
8th Edition
ISBN: 9781307434316
Author: CENGEL
Publisher: INTER MCG
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 2.8, Problem 34P

A ski lift has a one-way length of 1 km and a vertical rise of 200 m. The chairs are spaced 20 m apart, and each chair can seat three people. The lift is operating at a steady speed of 10 km/h. Neglecting friction and air drag and assuming that the average mass of each loaded chair is 250 kg, determine the power required to operate this ski lift. Also estimate the power required to accelerate this ski lift in 5 s to its operating speed when it is first turned on.

Expert Solution & Answer
Check Mark
To determine

The power required to operate the ski lift.

The power required to accelerate the ski lift in 5 s to its operating speed.

Answer to Problem 34P

The power required to operate the ski lift is 68.1kW_.

The power required to accelerate the ski lift in 5 s to its operating speed is 43.7kW_.

Explanation of Solution

Calculate the load of the lift at any given time.

m=N(w) (I)

Here, number of chairs at any given time is N and weight of each chair is w.

Calculate the work required to raise the mass by 200 m.

Wg=mg(z2z1) (II)

Here, acceleration due to gravity is g and difference between the elevation of ski lift is z2z1.

Write the equation of change in time.

Δt=DV (III)

Here, distance is D and velocity is V.

Calculate the power needed.

W˙g=Wgt2t1 (IV)

Calculate the acceleration of the ski lift.

a=ΔVΔt=V2V1t2t1 (V)

Here, change in velocity is ΔV, initial and final time is t1 and t2 respectively.

During the acceleration, calculate the power needed.

W˙a=12m(V22V12)t2t1 (VI)

Here, the initial and final velocity of a ski lift are V1 and V2 respectively.

Calculate the vertical distance travelled during the acceleration.

z2z1=hh=12at2sinα (VII)

Here, time to accelerate the ski lift to its operating speed is t and angle to raise the ski lift is α.

Calculate the power needed to acceleate the ski lift in 5 s.

W˙g=mg(h)t2t1 (VIII)

Calculate the total power required to accelerate the ski lift.

W˙total=W˙a+W˙g (IX)

Conclusion:

Since the lift is 1 km long and chairs are spaced 20 m apart, calculate the number of chairs at any given time.

N=1km20m=1km×1000(m1km)20m=50chairs

Substitute 50 chairs for N and 250 kg/chair for w in Equation (I).

m=(50chairs)(250kg/chair)=12,500kg

Substitute 12,500 kg for m, 9.81m/s2 for g, and 200 m for z2z1 in Equation (II).

Wg=(12,500kg)(9.81m/s2)(200m)=(12,500kg)(9.81m/s2)(200m)(1kJ1000kgm2/s2)=24,525kJ

Substitute 1 km for D and 10 km/h for V in Equation (III).

Δt=1km10km/h=0.1h×3600s1h=360s

Substitute 360 s for Δt and 24,525 kJ for Wg in Equation (IV).

W˙g=24,525kJ360s=68.1kW

Thus, the power required to operate the ski lift is 68.1kW_.

Convert the unit of velocity from km/h to m/s.

V=10kmh=10kmh×1000m1km×1h3600s=2.778m/s

Substitute 0 for V1, 2.778 m/s for V2, 0 for t1, and 5 s for t2 in Equation (V).

a=2.778m/s05s0=0.556m/s2

Substitute 0 for t1, 5 s for t2, 0 for V1, 12,500 kg for m, and 2.778 m/s for V2 in Equation (VI).

W˙a=12(12,500kg)((2.778m/s)2(0))5s0=12(12,500kg)(2.778m/s)25s(1kJ/kg1000m2/s2)×1kW1kJ/s=9.6kW

Calculate the value of sinα.

sinα=200m1km=200m1km×1000m1km=0.2

Substitute 0.556m/s2 for a, 5 s for t, and 0.2 for sinα in Equation (VII).

h=12(0.556m/s2)(5s)20.2=1.39m

Substitute 1.39 m for h, 5 s for t2, 0 for t1, 9.81m/s2 for g, and 12,500 kg for m in Equation (VIII).

W˙g=(12,500kg)9.81m/s2(1.39m)5s0=(12,500kg)9.81m/s2(1.39m)5s(1kJ1000kgm2/s2)×1kW1kJ/s=34.08kW34.1kW

Substitute 34.1 kW for W˙g and 9.6 kW for W˙a in Equation (IX).

W˙total=9.6kW+34.1kW=43.7kW

Thus, the power required to accelerate the ski lift in 5 s to its operating speed is 43.7kW_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A helicopter of mass 8.25 tonnes is flying at a rate of 175 Kmph, at a height of 3 x 105 cm above the ground level. Calculate the total energy possessed by the helicopter.
A 100 lb force exerted against a 1000-lb block causes the block to slide with constant velocity. The friction force on the block must be
A box of mass 80 kg is moving at a speed of 10 m/s on a ropeway. If the box is 40 m above the ground level, estimate the potential energy and kinetic energy of the box.

Chapter 2 Solutions

THERMODYNAMICS(SI UNITS,INTL.ED)EBOOK>I

Ch. 2.8 - Prob. 11PCh. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - A water jet that leaves a nozzle at 60 m/s at a...Ch. 2.8 - Prob. 14PCh. 2.8 - Prob. 15PCh. 2.8 - Consider a river flowing toward a lake at an...Ch. 2.8 - When is the energy crossing the boundaries of a...Ch. 2.8 - Consider an automobile traveling at a constant...Ch. 2.8 - A gas in a pistoncylinder device is compressed,...Ch. 2.8 - A room is heated by an iron that is left plugged...Ch. 2.8 - A room is heated as a result of solar radiation...Ch. 2.8 - Prob. 23PCh. 2.8 - A small electrical motor produces 5 W of...Ch. 2.8 - Prob. 25PCh. 2.8 - 2–26C Lifting a weight to a height of 20 m takes...Ch. 2.8 - Prob. 27PCh. 2.8 - Prob. 28PCh. 2.8 - Prob. 29PCh. 2.8 - Prob. 30PCh. 2.8 - Prob. 31PCh. 2.8 - Prob. 32PCh. 2.8 - Prob. 33PCh. 2.8 - A ski lift has a one-way length of 1 km and a...Ch. 2.8 - The engine of a 1500-kg automobile has a power...Ch. 2.8 - Prob. 36PCh. 2.8 - What are the different mechanisms for transferring...Ch. 2.8 - On a hot summer day, a student turns his fan on...Ch. 2.8 - Prob. 39PCh. 2.8 - A vertical pistoncylinder device contains water...Ch. 2.8 - At winter design conditions, a house is projected...Ch. 2.8 - A water pump increases the water pressure from 15...Ch. 2.8 - Prob. 43PCh. 2.8 - Prob. 44PCh. 2.8 - A university campus has 200 classrooms and 400...Ch. 2.8 - Prob. 46PCh. 2.8 - Consider a room that is initially at the outdoor...Ch. 2.8 - Prob. 48PCh. 2.8 - 2-49 The 60-W fan of a central heating system is...Ch. 2.8 - Prob. 50PCh. 2.8 - An escalator in a shopping center is designed to...Ch. 2.8 - Prob. 52PCh. 2.8 - How is the combined pumpmotor efficiency of a pump...Ch. 2.8 - Prob. 54PCh. 2.8 - Can the combined turbinegenerator efficiency be...Ch. 2.8 - Consider a 2.4-kW hooded electric open burner in...Ch. 2.8 - Prob. 57PCh. 2.8 - Prob. 58PCh. 2.8 - Prob. 59PCh. 2.8 - A geothermal pump is used to pump brine whose...Ch. 2.8 - Prob. 62PCh. 2.8 - Prob. 63PCh. 2.8 - The water in a large lake is to be used to...Ch. 2.8 - A 7-hp (shaft) pump is used to raise water to an...Ch. 2.8 - At a certain location, wind is blowing steadily at...Ch. 2.8 - Reconsider Prob. 265. Using appropriate software,...Ch. 2.8 - Water is pumped from a lake to a storage tank 15 m...Ch. 2.8 - Prob. 69PCh. 2.8 - A hydraulic turbine has 85 m of elevation...Ch. 2.8 - Prob. 71PCh. 2.8 - Water is pumped from a lower reservoir to a higher...Ch. 2.8 - Prob. 73PCh. 2.8 - An oil pump is drawing 44 kW of electric power...Ch. 2.8 - How does energy conversion affect the environment?...Ch. 2.8 - What is acid rain? Why is it called a rain? How do...Ch. 2.8 - Why is carbon monoxide a dangerous air pollutant?...Ch. 2.8 - What is the greenhouse effect? How does the excess...Ch. 2.8 - What is smog? What does it consist of? How does...Ch. 2.8 - Prob. 80PCh. 2.8 - Consider a household that uses 14,000 kWh of...Ch. 2.8 - When a hydrocarbon fuel is burned, almost all of...Ch. 2.8 - Prob. 83PCh. 2.8 - A typical car driven 20,000 km a year emits to the...Ch. 2.8 - What are the mechanisms of heat transfer?Ch. 2.8 - Which is a better heat conductor, diamond or...Ch. 2.8 - How does forced convection differ from natural...Ch. 2.8 - What is a blackbody? How do real bodies differ...Ch. 2.8 - Define emissivity and absorptivity. What is...Ch. 2.8 - Does any of the energy of the sun reach the earth...Ch. 2.8 - The inner and outer surfaces of a 5-m 6-m brick...Ch. 2.8 - The inner and outer surfaces of a 0.5-cm-thick 2-m...Ch. 2.8 - Reconsider Prob. 292. Using appropriate software,...Ch. 2.8 - Prob. 94PCh. 2.8 - Prob. 95PCh. 2.8 - Prob. 96PCh. 2.8 - Prob. 97PCh. 2.8 - For heat transfer purposes, a standing man can be...Ch. 2.8 - Prob. 99PCh. 2.8 - Prob. 100PCh. 2.8 - A 1000-W iron is left on the ironing board with...Ch. 2.8 - A 7-cm-external-diameter, 18-m-long hot-water pipe...Ch. 2.8 - A thin metal plate is insulated on the back and...Ch. 2.8 - Reconsider Prob. 2103. Using appropriate software,...Ch. 2.8 - The outer surface of a spacecraft in space has an...Ch. 2.8 - Prob. 106PCh. 2.8 - A hollow spherical iron container whose outer...Ch. 2.8 - Consider a vertical elevator whose cabin has a...Ch. 2.8 - Consider a homeowner who is replacing his...Ch. 2.8 - Prob. 110RPCh. 2.8 - Prob. 111RPCh. 2.8 - Prob. 112RPCh. 2.8 - 2–113 The U.S. Department of Energy estimates that...Ch. 2.8 - Prob. 114RPCh. 2.8 - Prob. 115RPCh. 2.8 - Prob. 116RPCh. 2.8 - Prob. 117RPCh. 2.8 - Consider a TV set that consumes 120 W of electric...Ch. 2.8 - Water is pumped from a 200-ft-deep well into a...Ch. 2.8 - Prob. 120RPCh. 2.8 - Prob. 121RPCh. 2.8 - In a hydroelectric power plant, 65 m3/s of water...Ch. 2.8 - The demand for electric power is usually much...Ch. 2.8 - The pump of a water distribution system is powered...Ch. 2.8 - On a hot summer day, the air in a well-sealed room...Ch. 2.8 - Prob. 126FEPCh. 2.8 - A 2-kW electric resistance heater in a room is...Ch. 2.8 - A 900-kg car cruising at a constant speed of 60...Ch. 2.8 - Prob. 129FEPCh. 2.8 - Prob. 130FEPCh. 2.8 - Prob. 131FEPCh. 2.8 - A 2-kW pump is used to pump kerosene ( = 0.820...Ch. 2.8 - Prob. 133FEPCh. 2.8 - Prob. 134FEPCh. 2.8 - Prob. 135FEPCh. 2.8 - Prob. 136FEPCh. 2.8 - Prob. 137FEPCh. 2.8 - Heat is transferred steadily through a...Ch. 2.8 - The roof of an electrically heated house is 7 m...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY