Which of the following statements is not true?   a. DTCs that will not affect emissions will never illuminate the MIL.     b. An active or current DTC represents a fault that was detected and occurred during two trips.     c. When a two-trip fault is detected for the second time, a DTC is stored as a pending code.     d. There are some DTCs that will set in one trip

Q: The final control element in a closed loop control system is known as correction element measurement…

A: The final control  element of control loop system is known as Measurement Element.

Q: A TPMS sensor is being replaced. Technician A says that if you replace it with a manufacturer…

A: Objective: To determine which statement is correct for replacing the TPMS sensor.

Q: _____ is a sensor used to measure temperature.

A: Thermocouple is the sensor used to measure temperature they are inexpensive ,durable .

Q: Which of the following will be used by a contact type sensor ? a. Ultrasonic Sound Wave b. Dial…

A:

Q: Explain the basic concept of Temperature and Pressure Sensor.

A: Given data : Temperature sensor Pressure sensor

Q: Sensing element - This takes the output of the sensing element and converts it into a form more…

A: The input signal can be anything which is measurable like pressure, temperature, weight, etc. and…

Q: Calibration is an example of maintenance activities.

A: calibration is an action, which is taking place on any device or component to insure that component…

Q: Integral controller has large overshoot. Select one: O True O False

A: Demerits System gets to be sluggish due to the expansion of fundamentally term. Takes bigger time…

Q: What is a solution to the following environmental risks in a SADA system Temperature Corrosion…

A: SADA system stands for Solar Array Drive Assemblies. These are the system in which the solar array…

Q: Which of the following memory circuits is used tostore trouble codes and other temporary…

A: A type of memory called ROM (Read-only Memory) is utilised to store data permanently.  Read-only and…

Q: q7    Alternation and inspection of equipment are the secondary functions of maintenance. Select…

A: The given statement is false.

Q: A STOL command line in galaxy is us- ommands to the spacecraft and to e procedures. O True O False

A: Given Data : STOL Command line  Blind commanding line

Q: I need parts 5 and 6 answered pertaining to the print and set of sequence of operations.   Note: If…

A: When the operator actuate the two-push button valves (1) and (2) until the weight starts to descend.…

Q: Variant CAPP is based on a group technology (GT) coding and classification approach. O True O False

A: CAPP --- Computer Aided Processing Planning Two types 1. Varient   2. Generative.

Q: Based on the circuit shown in Figure 19-11, complete the following exercises: A. Complete the chart…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Continuous level measurement in a tank filled with grain can be done using a _________ sensor.

A:

Q: 3. The intersection is controlled by traffic signal or by police officer, is called ... uncontrolled…

A: An intersection is a road junction where two or more roads either meet or cross at grade. This…

Q: A major disadvantage of on/off control is that it cannot work for applications requiring very small…

A: On-off controller (also called two-step controller) turns on or off the machine based on the error…

Q: Match the following terms with the definitions. Damping Bandwidth End point Home position…

A: Solution:   The following are correctly matched below:

Q: I need these 3 parts answered for a review activity.

A: Control frame has three compartments,Characteristic control compartment.Tolerance zone…

Q: Explain the Working of Ultrasonic Doppler flow sensor with Diagra

A: given: Explain the Working of Ultrasonic Doppler flow sensor with Diagram

Q: Technician A says that the oxygen sensor provides the major input during the open-loop…

A: There are two modes of operations for the engine: (1) Open loop mode: In this mode, no feedback is…

Q: Which of the following is a digital transducer

A: A. Strain gauge It is in the form of strip which is used to measure strain of a body. Change in…

Q: How many control parameters have to be specified in a PID controller? 1 none 2 4. 3 Which would…

A: Proportional (P), Integral (I), and Derivative (D) are the three parameters that a PID controller…

Q: True or False: The OFFSET command cannot be used on closed objects

A: The OFFSET command is used to create parallel lines, parallel curves and concentric circles at a…

Q: 6. Given a unidirectional controller for a sanitizer booth. It has 2 doors, a button for entrance…

A: according to given data

Q: Answer the following questions on diagnostic trouble codes (DTCs) relating to engine management…

A: Diagnostic Trouble Codes (DTC):  It is the essential codes that onboard computer diagnostics systems…

Q: Question: What is the main difference between active Sensor and passive Sensor: ( Select the…

A: A sensor transducer is a device which converts a physical form of signal into measurable form of…

Q: All manipulators don't have workspace-boundary singularities. O True O False

A: Boundary Singularities (too known as workspace singularities) are a common sort of peculiarity.…

Q: . _______ is a sensor that uses ‘time of flight’ method to determine liquid leve

A:

Q: In the following closed-loop control system, identify the dynamic system, the actuator, the…

A: Given: To find: Dynamic system, actuator, controlled variable, manipulated variable and control…

Q: Select appropriate sensors for a specified wire cutting system

A: To select appropriate sensors for a wire cutting system, it would be helpful to have more specific…

Q: timing diagram with IPO, IPC, TPO, TPC,EPO, EPC as 35,35,40,40,35,50

A: The port timing diagram for required functions with angle is shown below.

Q: ment time data in the table, calcula Failure rate x 10- (h)

A: The name itself is well explained as, the mean or average time needed to repair mechanical or…

Q: Which of the following is not a voltage-generating type sensor? vehicle speed sensor OSS MAP ISS

A: Voltage generating type sensors This type of generators consists of different types of speed sensors…

Q: Plz make the isometric view

A: The required isometric view is drawn below.

Q: Which datum surface does not belong to location datum category?

A: The operating datum surface does not belong to the location datum category.

Q: QUESTION 21 Smaller dirt particles are removed from the air by the filter's O deflector O baffle…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…