The necessity to have intake charge velocities of about 50 feet per second.

Question

Want to see more full solutions like this?

Answer 1

Question

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

37. The vertical shaft shown in Figure P12-37 is driven at a speed of 600 rpm with 4.0 hp entering through the bevel gear. Each of the two chain sprockets delivers 2.0 hp to the side to drive mixer blades in a chemical reactor vessel. The bevel gear has a diametral pitch of 5, a pitch diameter of 9.000 in, a face width of 1.31 in, and a pressure angle of 20°. Use SAE 4140 OQT 1000 steel for the shaft. See Chapter 10 for the methods for computing the forces on the bevel gear. Figure P12-37: P37-Bevel gear drive with two chain sprockets Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of strength. Homework Problems 12-24, 12-35, and 12-37 from textbook, done in spreadsheet form. Place drawings of the load, shear, and bending moment body diagrams…

35. The double-reduction, helical gear reducer shown in Figure P12-35 transmits 5.0 hp. Shaft 1 is the input, rotating at 1800 rpm and receiving power directly from an electric motor through a flexible coupling. Shaft 2 rotates at 900 rpm. Shaft 3 is the output, rotating at 300 rpm. A chain sprocket is mounted on the output shaft as shown and delivers the power upward. The data for the gears are given in Table 12-5. Each gear has a 1412° normal pressure angle and a 45° helix angle. The combinations of left- and right-hand helixes are arranged so that the axial forces oppose each other on shaft 2 as shown. Use SAE 4140 OQT 1200 for the shafts. Figure P12-35: P35-Double-reduction helical drive Each problem includes the following details: ■Design the complete shaft, including the specification of the overall geometry and the consideration of stress con- centration factors. The analysis would show the minimum acceptable diameter at each point on the shaft to be safe from the standpoint of…

Consider 0.65 kg of N2 at 300 K, 1 bar contained in a rigid tank connected by a valve to another rigid tank holding 0.3 kg of CO2 at 300 K, 1 bar. The valve is opened and gases are allowed to mix, achieving an equilibrium state at 290 K. Determine: (a) the volume of each tank, in m³. (b) the final pressure, in bar. (c) the magnitude of the heat transfer to or from the gases during the process, in kJ. (d) the entropy change of each gas and of the overall system, in kJ/K.

Answer 2

Question

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Question

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Question

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Answer 6

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.

Answer 7

Chapter 24, Problem 1RQ

To determine

The necessity to have intake charge velocities of about 50 feet per second.

Answer 8

Expert Solution & Answer

Explanation of Solution

The velocity of the fuel at the intake must be high enough to overcome the airstream between the intake value and the throttle body. At speeds more than 300 feet per second, the separation of droplets from the charge will occur. In order to prevent the droplet separation, the intake charge velocity must be around 50 feet per second. Hence, it is necessary to have intake charge velocity of about 50 feet per second to prevent the droplet fallout.