Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 22, Problem 8R
Sketch a weld on plates in the 4G and 4F positions.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Auto Controls
Using MATLAB , find the magnitude and phase plot of the compensators
NO COPIED SOLUTIONS
4-81 The corner shown in Figure P4-81 is initially uniform at 300°C and then suddenly
exposed to a convection environment at 50°C with h 60 W/m². °C. Assume the
=
2
solid has the properties of fireclay brick. Examine nodes 1, 2, 3, 4, and 5 and deter-
mine the maximum time increment which may be used for a transient numerical
calculation.
Figure P4-81
1
2
3
4
1 cm
5
6
1 cm
2 cm
h, T
+
2 cm
Auto Controls
A union feedback control system has the following open loop transfer function
where k>0 is a variable proportional gain
i. for K = 1 , derive the exact magnitude and phase expressions of G(jw).
ii) for K = 1 , identify the gaincross-over frequency (Wgc) [where IG(jo))| 1] and phase cross-overfrequency [where <G(jw) = - 180]. You can use MATLAB command "margin" to obtain there quantities.
iii) Calculate gain margin (in dB) and phase margin (in degrees) ·State whether the closed-loop is stable for K = 1 and briefly justify your answer based on the margin . (Gain marginPhase margin)
iv. what happens to the gain margin and Phase margin when you increase the value of K?you
You can use for loop in MATLAB to check that.Helpful matlab commands : if, bode, margin, rlocus
NO COPIED SOLUTIONS
Chapter 22 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 22 - List the five joint types used in welding.Ch. 22 - What stresses must a welded joint withstand?Ch. 22 - Sketch and label five edge preparations used for...Ch. 22 - Sketch a V-grooved butt joint, and label all of...Ch. 22 - Sketch a weld on plates in the 1G and 1F...Ch. 22 - Sketch a weld on plates in the 2G and 2F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on a pipe in the 1G position.Ch. 22 - Sketch a weld on a pipe in the 5G position.
Ch. 22 - Sketch a weld on a pipe in the 2G position.Ch. 22 - Sketch a weld on a pipe in the 6G position.Ch. 22 - Sketch a weld on a pipe in the 6GR position.Ch. 22 - Why are some joints back gouged?Ch. 22 - Why is it usually better to make a weld in the...Ch. 22 - What is a prequalified joint?Ch. 22 - Why is cost a consideration in joint design?Ch. 22 - Why are welding symbols used?Ch. 22 - What types of information can be included on a...Ch. 22 - Why is a tail added to the basic welding symbol?Ch. 22 - What types of information may appear on the...Ch. 22 - What are the different classifications of welds...Ch. 22 - How is the reference line always drawn?Ch. 22 - What is meant if the weld symbol is placed below...Ch. 22 - How are the dimensions for a fillet weld given?Ch. 22 - What dimensions can be given for a plug weld?Ch. 22 - What two units are used to show the minimum shear...Ch. 22 - How is the strength of a seam weld specified?Ch. 22 - How can the groove be cut on the edge of a plate?Ch. 22 - Sketch and dimension a V-groove weld symbol for a...Ch. 22 - How is the removal of the backing strip noted on a...Ch. 22 - How are flanged edges formed?Ch. 22 - Sketch two NDT symbols illustrating different...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Auto Controls Hand sketch the root Focus of the following transfer function How many asymptotes are there ?what are the angles of the asymptotes?Does the system remain stable for all values of K NO COPIED SOLUTIONSarrow_forward-400" 150" in Datum 80" 90" -280"arrow_forwardUsing hand drawing both of themarrow_forward
- A 10-kg box is pulled along P,Na rough surface by a force P, as shown in thefigure. The pulling force linearly increaseswith time, while the particle is motionless att = 0s untilit reaches a maximum force of100 Nattimet = 4s. If the ground has staticand kinetic friction coefficients of u, = 0.6 andHU, = 0.4 respectively, determine the velocityof the A 1 0 - kg box is pulled along P , N a rough surface by a force P , as shown in the figure. The pulling force linearly increases with time, while the particle is motionless at t = 0 s untilit reaches a maximum force of 1 0 0 Nattimet = 4 s . If the ground has static and kinetic friction coefficients of u , = 0 . 6 and HU , = 0 . 4 respectively, determine the velocity of the particle att = 4 s .arrow_forwardCalculate the speed of the driven member with the following conditions: Diameter of the motor pulley: 4 in Diameter of the driven pulley: 12 in Speed of the motor pulley: 1800 rpmarrow_forward4. In the figure, shaft A made of AISI 1010 hot-rolled steel, is welded to a fixed support and is subjected to loading by equal and opposite Forces F via shaft B. Stress concentration factors K₁ (1.7) and Kts (1.6) are induced by the 3mm fillet. Notch sensitivities are q₁=0.9 and qts=1. The length of shaft A from the fixed support to the connection at shaft B is 1m. The load F cycles from 0.5 to 2kN and a static load P is 100N. For shaft A, find the factor of safety (for infinite life) using the modified Goodman fatigue failure criterion. 3 mm fillet Shaft A 20 mm 25 mm Shaft B 25 mmarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License