Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 22, Problem 4ASRQ
Technician A says that multiplexing is a way to add wires without increasing the weight of the vehicle. Technician B says that multiplexing uses bus data links. Who is correct?
- Technician A
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
hile discussing NTC thermistors; Technician A says that some systems use this type of thermistor as a protection device. Technician B says that when there is high current in a circuit, the resistance of the thermistor increases and causes a decrease in current flow. Who is correct?
Question 4
0/1
Which of the following is an example of electronic technology?
The xbox
Windshield wipers
Legs of a chair
Lasers
2/. The _____________ between the windings of a transformer is the same.
current
induced emf
voltage
frequency
Chapter 22 Solutions
Automotive Technology
Ch. 22 - Explain the three types of memory used in the...Ch. 22 - Signals resemble a square pattern.Ch. 22 - Signals can have varying voltage levels.Ch. 22 - Means that data concerning the effects of the...Ch. 22 - The type of memory' that contains specific...Ch. 22 - A is the simplest type of semiconductor.Ch. 22 - Prob. 7SACh. 22 - Prob. 8SACh. 22 - How should vou test a diode with a multimeter?Ch. 22 - What is the name of the module that allows the...
Ch. 22 - What is the major difference between ROM and RAM...Ch. 22 - True or False? In a high-speed CAN system, a...Ch. 22 - True or False? In a high-speed CAN system, a...Ch. 22 - Which of the following is not made of...Ch. 22 - Which of the following is a basic function of a...Ch. 22 - Prob. 1ASRQCh. 22 - While checking an A/C compressor clutch coil...Ch. 22 - Technician A says that some types of voltage...Ch. 22 - Technician A says that multiplexing is a way to...Ch. 22 - Technician A says that when a diode is placed in a...Ch. 22 - Prob. 6ASRQCh. 22 - While discussing multiplex system protocols:...Ch. 22 - Prob. 8ASRQCh. 22 - While diagnosing a network communication failure:...Ch. 22 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? In a high-speed CAN system, a serial data bus is used to allow communication between the various control modules in a vehicle.arrow_forwardWhile discussing multiplex system protocols: Technician A says that CAN communications are based on variable pulse widths carried on a single bus wire. Technician B says that Class B communications offer real-time communications over a twisted pair of wires. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen working on a high-voltage system, it is best to keep anyone who is not part of the service away from you and the car by creating a buffer zone around the car. Technician A makes sure the outside edges of the zone are at least one foot away from the car. Technician B places orange cones to define the outer boundaries of the zone. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- While discussing electrical grounds: Technician A says that a component may be grounded through its mounting to a major metal part. Technician B says that some components must be grounded by connecting its positive terminal to a metal section of the frame. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that before a battery is removed, a memory' saver ought to be installed. Technician B says that before a battery is removed, the positive cable should be disconnected and the area around the battery should be cleaned. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile diagnosing a network communication failure: Technician A checks for communication codes in the problem network. Technician B checks for DTCs in all networks and modules. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- While diagnosing an electronic control system: Technician A turns the ignition off before disconnecting a connector or component. Technician B uses a jumper wire to bypass a potentially faulty sensor and then observes the scan tool. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that the waveform produced by an AC generator after rectification is called a sine wave. Technician B says that the waveform produced by the AC generator after the output moves through the diodes is a straight line because it is a constant DC voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- Technician A says that the suspension switch must be turned off before raising any corner of a car with an electronic air suspension. Technician B says that the ignition switch must not be turned on while any corner of a car with electronic air suspension is raised. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardList five things a driver of a BEV can do to extend the driving range of the vehicle.arrow_forwardWhile diagnosing the location of a wire-to-wire short: Technician A checks the wiring of the affected circuits for signs of burned insulation and melted conductors. Technician B checks common connectors shared by the two affected circuits. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License