Bundle: Welding: Principles and Applications, 8th + MindTap Welding, 4 terms (24 months) Printed Access Card
8th Edition
ISBN: 9781337219426
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 22, Problem 1R
List the five joint types used in welding.
Expert Solution & Answer
To determine
The five types of joints in welding.
Explanation of Solution
Welding joints are of five types:
- Butt joint
- Lap joint
- Tee joints
- Outline corner joint
- Edge joint
Butt joint:
It is a type of welding in which the edges are welded. This do not increase the width of the metal. It has flexibility of being welded from both sides. Edges of metal are kept parallel for welding.
Lap joint:
In this welding, edges of the metal are overlapped to perform the welding operations. A fillet weld is used for performing lap joint. Welds can be performed on either side of the metal pieces.
Tee joints:
In this welding, the surface of one metal is placed over the surface of other metal. The angle between the parts to be welded is right angle. This welding is done by fillet welding.
Outline corner joint:
In this welding, a piece of metal is brought in contact by making an angle of 90-degree. Corners of edged are put together for welding.
Edge joint:
Even edges of two metals are put together by side to perform welding. These joints can be welded from one side only.
Types of welding can be seen in given figure.
Fig: types of weld joints
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A viscoelastic column is made of a material with a creep compliance of
D(t)= 0.75+0.5log10t+0.18(log10t)^2 GPA^-1
for t in s. If a constant compressive stress of σ0 = –100 MPa is applied at t = 0, how long will it take (= t1/2) for the height of the column to decrease to ½ its original value? Note: You will obtain multiple answers for this problem! One makes sense physically and one does not.
A group of 23 power transistors, dissipating 2 W each, are to be cooled by attaching them to a black-anodized square aluminum plate and mounting the plate on the wall of a room at 30°C. The emissivity of the transistor and the plate surfaces is 0.9. Assuming the heat transfer from the back side of the plate to be negligible and the temperature of the surrounding surfaces to be the same as the air temperature of the room, determine the length of the square plate if the average surface temperature of the plate is not to exceed 50°C. Start the iteration process with an initial guess of the size of the plate as 43 cm.
The properties of air at 1 atm and the film temperature of (Ts + T)/2 = (50 + 30)/2 = 40°C are k = 0.02662 W/m·°C, ν = 1.702 × 10–5 m2 /s, Pr = 0.7255, and β = 0.003195 K–1.
Multiple Choice
0.473 m
0.284 m
0.513 m
0.671 m
A 40-cm-diameter, 127-cm-high cylindrical hot water tank is located in the bathroom of a house maintained at 20°C. The surface
temperature of the tank is measured to be 44°C and its emissivity is 0.4. Taking the surrounding surface temperature to be also 20°C,
determine the rate of heat loss from all surfaces of the tank by natural convection and radiation.
The properties of air at 32°C are k=0.02603 W/m-K, v=1.627 x 10-5 m²/s, Pr = 0.7276, and ẞ = 0.003279 K-1
The rate of heat loss from all surfaces of the tank by natural convection is
The rate of heat loss from all surfaces of the tank by radiation is
W.
W.
Chapter 22 Solutions
Bundle: Welding: Principles and Applications, 8th + MindTap Welding, 4 terms (24 months) Printed Access Card
Ch. 22 - List the five joint types used in welding.Ch. 22 - What stresses must a welded joint withstand?Ch. 22 - Sketch and label five edge preparations used for...Ch. 22 - Sketch a V-grooved butt joint, and label all of...Ch. 22 - Sketch a weld on plates in the 1G and 1F...Ch. 22 - Sketch a weld on plates in the 2G and 2F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on a pipe in the 1G position.Ch. 22 - Sketch a weld on a pipe in the 5G position.
Ch. 22 - Sketch a weld on a pipe in the 2G position.Ch. 22 - Sketch a weld on a pipe in the 6G position.Ch. 22 - Sketch a weld on a pipe in the 6GR position.Ch. 22 - Why are some joints back gouged?Ch. 22 - Why is it usually better to make a weld in the...Ch. 22 - What is a prequalified joint?Ch. 22 - Why is cost a consideration in joint design?Ch. 22 - Why are welding symbols used?Ch. 22 - What types of information can be included on a...Ch. 22 - Why is a tail added to the basic welding symbol?Ch. 22 - What types of information may appear on the...Ch. 22 - What are the different classifications of welds...Ch. 22 - How is the reference line always drawn?Ch. 22 - What is meant if the weld symbol is placed below...Ch. 22 - How are the dimensions for a fillet weld given?Ch. 22 - What dimensions can be given for a plug weld?Ch. 22 - What two units are used to show the minimum shear...Ch. 22 - How is the strength of a seam weld specified?Ch. 22 - How can the groove be cut on the edge of a plate?Ch. 22 - Sketch and dimension a V-groove weld symbol for a...Ch. 22 - How is the removal of the backing strip noted on a...Ch. 22 - How are flanged edges formed?Ch. 22 - Sketch two NDT symbols illustrating different...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 2.5-m-long thin vertical plate is subjected to uniform heat flux on one side, while the other side is exposed to cool air at 5°C. The plate surface has an emissivity of 0.73, and its midpoint temperature is 55°C. Determine the heat flux subjected on the plate surface. Uniform heat flux -Plate, € = 0.73 Cool air 5°C 7 TSUIT Given: The properties of water at Tf,c= 30°C. k=0.02588 W/m.K, v=1.608 x 10-5 m²/s Pr = 0.7282 The heat flux subjected on the plate surface is W/m²arrow_forwardHot water is flowing at an average velocity of 5.82 ft/s through a cast iron pipe (k=30 Btu/h-ft-°F) whose inner and outer diameters are 1.0 in and 1.2 in, respectively. The pipe passes through a 50-ft-long section of a basement whose temperature is 60°F. The emissivity of the outer surface of the pipe is 0.5, and the walls of the basement are also at about 60°F. If the inlet temperature of the water is 150°F and the heat transfer coefficient on the inner surface of the pipe is 30 Btu/h-ft².°F, determine the temperature drop of water as it passes through the basement. Evaluate air properties at a film temperature of 105°C and 1 atm pressure. The properties of air at 1 atm and the film temperature of (Ts+ T∞)/2 = (150+60)/2 = 105°F are k=0.01541 Btu/h-ft-°F. v=0.1838 × 10-3 ft2/s, Pr = 0.7253, and ẞ = 0.00177R-1arrow_forwardhand-written solutions only, please. correct answers upvoted!arrow_forward
- hand-written solutions only, please. correct answers upvoted!arrow_forward! Required information Consider a flat-plate solar collector placed horizontally on the flat roof of a house. The collector is 1.3 m wide and 2.8 m long, and the average temperature of the exposed surface of the collector is 42°C. The properties of air at 1 atm and the film temperature are k=0.02551 W/m-°C, v = 1.562 × 10-5 m²/s, Pr = 0.7286, and ẞ= 0.003356 K-1 Determine the rate of heat loss from the collector by natural convection during a calm day when the ambient air temperature is 8°C. The rate of heat loss from the collector by natural convection is W.arrow_forwardhand-written solutions only, please. correct answers upvoted!arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY