Concept explainers
(a)
The amount of
(a)
Answer to Problem 29PQ
The amount of heat transferred in order for the whole process to take place is
Explanation of Solution
Write the equation for the total heat transferred.
Here,
Write the expression of the heat energy required to raise the temperature to the melting point.
Here,
Write the expression of the heat energy required to raise the temperature to final temperature.
Here,
Rewrite the expression for the total heat transferred from equation (I) by using (II) and (III).
Conclusion:
Substitute
Thus, the amount of heat transferred in order for the whole process to take place is
(b)
The amount of heat transferred to raise copper to its melting point.
(b)
Answer to Problem 29PQ
The amount of heat transferred to raise copper to its melting point is
Explanation of Solution
Write the expression of the heat energy required to raise the temperature to the melting point.
Here,
Conclusion:
Substitute,
Thus, the amount of heat transferred to raise copper to its melting point is
(c)
The amount of heat transferred during phase change.
(c)
Answer to Problem 29PQ
The amount of heat transferred during phase change is
Explanation of Solution
Write the expression of the heat energy required phase change.
Here,
Conclusion:
Substitute
Thus, the amount of heat transferred during phase change is
The approximation is the specific heat of solid copper and the liquid copper is considered as same. The energy is required for copper is about double comparing to the silver.
Want to see more full solutions like this?
Chapter 21 Solutions
Physics for Scientists and Engineers: Foundations and Connections
- A 3.00-g lead bullet at 30.0C is fired at a speed of 2.40 102 m/s into a large, fixed block of ice at 0C, in which it becomes embedded. (a) Describe the energy transformations that occur as the bullet is cooled. What is the final temperature of the bullet? (b) What quantity of ice melts?arrow_forward(a) How much heat transfer is required to raise the temperature of a 0.750kg aluminum pot containing 2.50 kg of water from 30.0C to the boiling point and then boil away 0.750 kg of water? (b) How long does this take if the rate of heat transfer is 500 W 1watt=ljoule/second(lW=lJ/s) ?arrow_forwardA high-end gas stove usually has at least one burner rated at 14 000 Btu/h. (a) If you place a 0.25-kg aluminum pot containing 2.0 liters of water at 20.C on this burner, how long will it take to bring the water to a boil, assuming all the heat from the burner goes into the pot? (b) Once boiling begins how much time is required to boil all the water out of the pot?arrow_forward
- What does it mean to say that two systems are in thermal equilibrium?arrow_forward(a) Why does an ordinary glass dish usually break when placed on a hot stove? (b) Dishes made of Pyrex glass dont break as easily. What characteristic of Pyrex prevents breakage?arrow_forward(a) Calculate the rate of heat conduction through house walls that are 13.0 cm thick and have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The walls' surface area is 120 m2 and their inside surface is at 18.0 , while their outside surface is at 5.00 . (b) How many 1-kW room heaters would be needed to balance the heat transfer due to conduction?arrow_forward
- (a) Calculate the rate of heat conduction through house walls that are 13.0 cm thick and that have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The surface area of the walls is 120m2 and their inside surface is at 18.0C, while their outside surface is at 5.00C. (b) How many 1-kW room heaters would be needed to balance the heat transfer due to conduction?arrow_forwardA hollow aluminum cylinder 20.0 cm deep has an internal capacity of 2.000 L at 20.0C. It is completely filled with turpentine at 20.0C. The turpentine and the aluminum cylinder are then slowly warmed together to 80.0C. (a) How much turpentine overflows? (b) What is the volume of the turpentine remaining in the cylinder at 80.0C? (c) If the combination with this amount of turpentine is then cooled back to 20.0C, how far below the cylinders rim does the turpentines surface recede?arrow_forwardA cup of hot water has a temperature of 80°C and is placed in a room that has a temperature of 25°C. After 15 minutes, it cooled down to 66°C. Find the constant k of the water. O a. 0.01 O b. -0.2 C. -0.02 O d. 0.02arrow_forward
- no handwrittenarrow_forwardChoose the correct answer 1. You have a 90 cm long iron rod at 15 ° C that heats up to 300 ° C. What happens with the rod is that: A. It melts. B. Double the length. C. Decrease its length a few centimeters. D. Increase its length by a few millimeters. 2. A student blows up a balloon and places it in his home freezer. After a long time, the balloon is removed from the freezer and it is observed that: A. The volume decreases as a certain amount of air escapes. B. It remains the same, because the air inside it does not expand or contract. C. The volume increases, because the air inside it expands D. The volume decreases as the air inside it contractsarrow_forwardSpecific Heat Worksheet q=(mass) (Csp)(AT) Units for specific heat = J g. °C 1. What is the specific heat of a substance that absorbs 2.5 x 10³ joules of heat when a sample of 1.0 x 10 g of the substance increases in temperature from 10.0°C to 70.0°C? 2. How many grams of water would require 2.20 x 104 joules of heat to raise its temperature from 34.0°C to 100.0°C? The specific heat of water is 4.18 J/g °C 3. If 200. grams of water is to be heated from 24.0°C to 100.0°C to make a cup of tea, how much heat must be added? The specific heat of water is 4.18 J/g °C 4. A block of aluminum weighing 140. g is cooled from 98.4°C to 62.2°C with the release of 1080 joules of heat. From this data, calculate the specific heat of aluminum 5. A cube of gold weighing 192.4g is heated from 30.0°C to some higher temperature, with the absorption of 226 joules of heat. The specific heat of gold is 0.030 J/g °C. What was the final CS Stemperature of the soldamScanner `6arrow_forward
- College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax College