Electrical Transformers and Rotating Machines
4th Edition
ISBN: 9781305494817
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 9RQ
To determine
The maximum induced voltage when the switch is opened.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
1.7 (A). A bar ABCD consists of three
sections: AB is 25 mm square and 50
mm long, BC is of 20 mm diameter and
40 mm long and CD is of 12 mm
diameter and 50 mm long. Determine
the stress set up in each section of the
bar when
it is subjected to an axial tensile load
of 20 kN. What will be the total
extension of the bar under this load?
For the bar
material, E = 210GN/m2. [32,63.7,
176.8 MN/mZ, 0.062mrn.l
10:41 م
2.2 (A). If the maximum stress allowed
in the copper of the cable of problem
2.1 is 60 MN/m2, determine the
maximum tension which C3.75 kN.1
10:41 م
1.1 (A). A 25mm squarecross-section
bar of length 300mm carries an axial
compressive load of 50kN.
Determine the stress set up ip the bar
and its change of length when the load
is applied. For the bar material
E = 200 GN/m2. [80 MN/m2; 0.12mm.l
Chapter 2 Solutions
Electrical Transformers and Rotating Machines
Ch. 2 - What determines the polarity of magnetism when...Ch. 2 - What determines the strength of the magnetic field...Ch. 2 - Prob. 3RQCh. 2 - How many lines of magnetic flux must be cut in 1 s...Ch. 2 - Prob. 5RQCh. 2 - Into how many time constants is an exponential...Ch. 2 - Each time constant of an exponential curve is...Ch. 2 - An inductor has an inductance of 0.025 H and a...Ch. 2 - Prob. 9RQCh. 2 - What electronic component is often used to prevent...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 2.1 (A). A power transmission cable consists of ten copper wires each of 1.6 mm diameter surrounding three steel wires each of 3 mm diameter. Determine the combined E for the compound cable and hence determine the extension of a 30 m length of the cable when it is being laid with a tension of 2 kN. For steel, E200 GN/mZ; for copper, E = 100 GN/mZ. C151.3 GN/mZ; 9.6 mm.] 10:41 مarrow_forwardquestion 662 thank youarrow_forward1.5 (A). A simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally at each end to take two rods of 25 mm outside diameter with threaded ends. What will be the nominal stresses set up in the tube and the rods, ignoring thread depth, when the turnbuckle cames an axial load of 30 kN? Assuming a sufficient strength of thread, what maximum load can be transmitted by the turnbuckle if the maximum stress is limited to 180 MN/mz? C39.2, 61.1 MN/m2, 88.4 kN.1arrow_forward
- 1.3 (A). Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in the two materials must not exceed 50 MN/m2 and 100 MN/ mZ respectively. C27.6, 19.5, 19.5, 13.8mm.l 11arrow_forward1.4 (A). Two forkend pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin? C1.39 x 10e4mZ; 50.9MN/mZ.] 10:41arrow_forward1.2 (A). A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN. What will be the stress in the bar? What further increase in load is possible if the stress in the bar is limited to 225 MN/mZ? [lo6 MN/m3; 45 kN.1arrow_forward
- 1.11 (a) A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, of diameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine: (i) the stress, (ii) the strain, (hi) the modulus of elasticity. (b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250mm. both measurements being made at 20°C. The temperature of the spacer is then increased to 100°C, the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/"C determine: (i) the stress in the spacer, (ii) the compressive load on the spacer. [C.G.] [64MN/m2, 0.0008, 80GN/m2, 115.2 MN/m2, 71 KN.] 10:41arrow_forwardI have attached an image, In that they have mentioned the tolerance of 0.4 for all surfaces. I need to know what's the exact tolerance.arrow_forwardSolve this problem and show all of the workarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Electrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning