DESIGN OF MACHINERY (LL W/ CONNECT)
6th Edition
ISBN: 9781265116712
Author: Norton
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 2, Problem 2.68P
Figure P2-25 shows a sixbar linkage.
- Is it a Watt or Stephenson linkage?
- Determine its inversion, i.e., is it a type I, II, or III’?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The number of degrees of freedom of the linkage shown in the figure.
Figure Q2-2 shows a schematic of a retractable landing gear of aircraft.
The retraction mechanism is a 4 bar linkage (O1ABO2), which is actuated
by a hydraulic cylinder and piston, D, pivoted at E with a joint at C to link
O,A.
Hydraulic cylinder
& piston D
Joint for landing
gear wheel
Figure Q2-2
Use the Gruebler's equation of DoF (Degrees of Freedom) of a
linkage mechanism to assess if the landing gear produces the
required retraction motion. 0,02 may be considered as the ground
link.
i)
Hint: The joint of the wheel is not part of the linkage mechanism.
The number of DoF may be used to check if it is a linkage with
certain motions or a fixed structure.
ii)
The dimensions of the 4 bar linkage (O1ABO2) are measured as
O102 = 800 mm, O1A = 780 mm, AB = 200 mm and O2B = 400
mm. Use Grashof condition to determine the specific type of this
linkage.
You may find the Gruebler's equation useful:
M = 3(L – 1) – 2J
where, M is degree of freedom (DoF)
L is number of links
J is number of joints
dont give wrong solution
Chapter 2 Solutions
DESIGN OF MACHINERY (LL W/ CONNECT)
Ch. 2 - Find three (or other number as assigned) of the...Ch. 2 - How many DOF do you have in your wrist and hand...Ch. 2 - How many DOF do the following joints have? Your...Ch. 2 - How many DOF do the following have in their normal...Ch. 2 - Are the joints in Problem 2-3 force closed or form...Ch. 2 - Describe the motion of the following items as pure...Ch. 2 - Calculate the mobility of the linkages assigned...Ch. 2 - Identify the items in Figure P2-1 as mechanisms,...Ch. 2 - Use linkage transformation on the linkage of...Ch. 2 - Prob. 2.10P
Ch. 2 - Use number synthesis to find all the possible link...Ch. 2 - Prob. 2.12PCh. 2 - Use linkage transformation to create a 1-DOF...Ch. 2 - Use linkage transformation to create a 1-DOF...Ch. 2 - Calculate the Grashof condition of the fourbar...Ch. 2 - Prob. 2.16PCh. 2 - Describe the difference between a cam-follower...Ch. 2 - Examine an automobile hood hinge mechanism of the...Ch. 2 - Find an adjustable arm desk lamp of the type shown...Ch. 2 - The torque-speed curve for a 1/8 hp permanent...Ch. 2 - Find the mobility of the mechanisms in Figure...Ch. 2 - Find the Grashof condition and Barker...Ch. 2 - Find the rotatability of each loop of the...Ch. 2 - Find the mobility of the mechanisms in Figure...Ch. 2 - Find the mobility of the ice tongs in Figure P2-6:...Ch. 2 - Prob. 2.26PCh. 2 - Prob. 2.27PCh. 2 - Find the mobility of the corkscrew in Figure P2-9.Ch. 2 - Figure P2-10 shows Watts sun and planet drive that...Ch. 2 - Figure P2-11 shows a bicycle handbrake lever...Ch. 2 - Figure P2-12 shows a bicycle brake caliper...Ch. 2 - Find the mobility, the Grashof condition, and the...Ch. 2 - The approximate torque-speed curve and its...Ch. 2 - Prob. 2.34PCh. 2 - Prob. 2.35PCh. 2 - Sketch the equivalent linkage for the cam and...Ch. 2 - Describe the motion of the following rides,...Ch. 2 - For the mechanism in Figure P2-1 a, number the...Ch. 2 - Repeat Problem 2-38 for Figure P2-1b.Ch. 2 - Repeat Problem 2-38 for Figure P2-1c.Ch. 2 - Prob. 2.41PCh. 2 - Find the mobility, the Grashof condition, and the...Ch. 2 - Find the mobility, the Grashof condition, and the...Ch. 2 - Figure P2-20 shows a Rube Goldberg mechanism that...Ch. 2 - All the eightbar linkages in Figure 2-11 part 2...Ch. 2 - Prob. 2.46PCh. 2 - Prob. 2.47PCh. 2 - Find the mobility of the mechanism shown in Figure...Ch. 2 - Find the mobility of the mechanism shown in Figure...Ch. 2 - Find the mobility of the mechanism shown in Figure...Ch. 2 - Find the mobility of the mechanism shown in Figure...Ch. 2 - Prob. 2.52PCh. 2 - Prob. 2.53PCh. 2 - Repeat Problem 2-38 for Figure P2-1f.Ch. 2 - Repeat Problem 2-38 for Figure P2-1g.Ch. 2 - For the example linkage shown in Figure 2-4 find...Ch. 2 - For the linkage shown in Figure 2-5b find the...Ch. 2 - Prob. 2.58PCh. 2 - Figure P2-21b shows a mechanism. Find its mobility...Ch. 2 - Prob. 2.60PCh. 2 - Figure P2-21 d shows a log transporter. Draw a...Ch. 2 - Figure P2-21e shows a plow mechanism attached to a...Ch. 2 - Figure P2-22 shows a Hart inversor sixbar linkage....Ch. 2 - Figure P2-23 shows the top view of the partially...Ch. 2 - Figure P2-24a shows the seat and seat-back of a...Ch. 2 - Figure P2-24b shows the mechanism used to extend...Ch. 2 - Figure P2-24b shows the mechanism used to extend...Ch. 2 - Figure P2-25 shows a sixbar linkage. Is it a Watt...Ch. 2 - Use number synthesis o find all the possible link...Ch. 2 - Use number synthesis to find all the possible link...Ch. 2 - Prob. 2.71PCh. 2 - For the mechanism in Figure P2-26, number the...Ch. 2 - Figure P2-27 shows a schematic of an exercise...Ch. 2 - Calculate the mobility of the linkage in Figure...Ch. 2 - Calculate the Grashof condition of the fourbar...Ch. 2 - The drum brake mechanism in Figure P2-4g is a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Figure below shows a four-bar linkage (non-scaled diagram) at an instant. The input angle is equal to the output angle (02 - 04) and the transmission angle is 30°. The input link is extended beyond joint B and an input force (Fin) is applied at the end of it, while an output force is drawn from the midpoint of the output link. If an output force of 30 N is desired from an input force of 10 N, how far the input link should be extended, i.e., what is the distance from point B to the point where Fin is applied. Fin B out undefined 02 04 A. Non-scaled diagram; AB = 10, CD=r4 = 30 (output), all in mmarrow_forwardThe lengths of various links of a mechanism, as shown in Figure 2, are: OA = 0.3 m; AB = 1 m; CD = 0.8 m; and AC = CB. A 45° В Figure 2: Slider cranck mechanism Draw the displacemt diagram to a scale.arrow_forwardIs there a two extreme position on this diagram? This diagram makes complete revolution. Also, what type of four-bar linkages this is. Measurements Fixed bar: 5 Red: 10 Green: 15 Blue: 20arrow_forward
- A general pinjointed fourbar linkage is shown in the figure below. It has the followings The link lengths are L1 = 8.50 in., L2 = 3.00 in., L3 = 5.00 in. and L4 = 4.50 in. The values of 0, = 0, 02 = 60°, and 04 = 119°. The angular velocity of link2 w2 = 10 rad/s CCW. L4 L2 02= 60° @2 B. Ao O = 0° Figure 5.32 Problems 5.3 and 5.4 The angular velocities of link 3 w3 and and link 4 w4 are: Select one: O a. w3 5.29rad/s CW, w4 = 6.14 rad/s CW O b. w3 = 3.94 rad/s CCW, w4 = 4.8 rad/s CCW O c. W3 5.29 rad/s CW, w4 = 4.80 rad/s CCW O d. w3 = 3.94 rad/s CCW, W4 = 6.14 rad/s CCWarrow_forward= Given the crank-slider linkage shown in Figure 1 with the linkage lengths as follows: L₂= 500 mm, L32 250 mm, and L₁= 550 mm. The distance between the supports is L₁ = 500 mm. When the angles of the links are 8₂ 36.87° and 83 53.13° the rotational angle rates of the links are wz 8 rad/s and w3 = -11.8859 rad/s. If the link R, is rotating in counterclockwise (CCW) direction with a rotational acceleration of az 5 rad/s², determine the rotational acceleration of links R₂ and the acceleration of the slider R2 03 R₁ R3 isin) R4arrow_forwardA series of three links is given with lengths of 2.4 ", 7.2" and 3.4 ", select the length of a fourth link, that when assembling the mechanism one of the links can be driven by a motor that rotates continuously. Mechanism is according to Grashoff, show all your operations to justify your resultsarrow_forward
- need help with correct answer pleasearrow_forwardThe lengths of various links of a mechanism, as shown in Figure 2, are: OA = 0.3 m; AB = 1 m; CD = 0.8 m; and AC = CB. A upuu 45° Figure 2: Slider cranck mechanism Draw the displacemt diagram to a scale.arrow_forwardSketch the kinematic diagram and calculate the mobility of all the linkages (Degrees of Freedom). Are there any assumptions if any.arrow_forward
- Show Links/Joints in diagram. Need within 15-30min with correct answer (Don't hold for long time )arrow_forwardA general pinjointed fourbar linkage is shown in the figure below. It has the followings: The link lengths are L1 = 8.50 in., L2 = 3.00 in., L3 = 5.00 in. and L4 = 4.50 in. The values of e1 = 0, 02 = 60°, and 04 = 119°. The angular velocity of link2 w2 = 10 rad/s CCW. L4 2 = 60° Ao B. O, = 0° Figure 5.32 Problems 5.3 and 5.4 The angular velocities of link 3 wz and and link 4 wa are: Select one: O a. w3 = 5.29rad/s CW, w4 = 6.14 rad/s CW O b. w3 = 3.94 rad/s CCW, W4 = 4.8 rad/s CCW O c. W3 = 3.94 rad/s CCW, wa = 6.14 rad/s CCW %3D O d. w3 = 5.29 rad/s CW, w4 = 4.80 rad/s CCW %3D %3Darrow_forward1. Find a combination of link lengths where motion of a point on output link is one quarter of a circle. 2. Find the value of all 0, 0, 0, and y in open and close configuration Read the value of link lengths and the input angle 8., then use the formulae given below to calculate the value of unknowns 03, 0, and y K₁ = = K₂= d K2 K3 = a²-b²+c²+d² 2ac A = cos 0₂ - K₁ - K₂ cos 0₂ + K3 B = -2 sin 0₂ C = K₁ (K₂ + 1) cos 02 + K3 -B± √B²-4AC 2A 0412 = 2tan-1 d K₁ = — K5 = c²d²a²-6² 2ab D = cos 0₂ - K₁ - K4 cos 0₂ + K5 E = -2 sin 0₂ FK₁+ (K₁ - 1) cos 02 +K5 0312 2 tan-1 (-E± -E± √E²4DF 2D Y = 04-03arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License