
(a)
Interpretation:
: To convert 2 wk to microseconds.
Concept introduction:
The international system of unit (SI units):
Day is represented by the symbol. | d |
Week is represented by the symbol | wk |
Hour is represented by the symbol | h |
Minutes is represented by the symbol | min |
Seconds is represented by the symbol | s |
Microsecond is represented by the symbol | µs |
Meter is represented by the symbol | m |
Feet is represented by the symbol | ft |
Kilometer is represented by the symbol | km |
Kilogram is represented by the symbol | kg |
Pound is represented by the symbol | lb |

Answer to Problem 2.1P
In two weeks there are
Explanation of Solution
In one week there are seven days and in one day there are twenty-four hours. In one hour there are sixty minutes and in one minute there are sixty seconds. In one second there are 106 microseconds.
Convert week to microseconds as follows:
(b)
Interpretation:
To convert 38.1 ft/s to kilometers/h.
Concept introduction:
The international system of unit (SI units):
Day is represented by the symbol | d |
Week is represented by the symbol | wk |
Hour is represented by the symbol | h |
Minutes is represented by the symbol | min |
Seconds is represented by the symbol | s |
Microsecond is represented by the symbol | µs |
Meter is represented by the symbol | m |
Feet is represented by the symbol | ft |
Kilometer is represented by the symbol | km |
Kilogram is represented by the symbol | kg |
Pound is represented by the symbol | lb |

Answer to Problem 2.1P
In
Explanation of Solution
In one day there are twenty-four hours and in one hour there are sixty minutes.
In one pound there are 0.453593 kg and in one feet there are 0.3048 m. Convert meter per day into kilogram to feet per minute into pound as follows:
(c)
Interpretation:
To convert 554 m4/(day.kg) to ft4/(min.lbm ).
Concept introduction:
The international system of unit (SI units):
Day is represented by the symbol | d |
Week is represented by the symbol | wk |
Hour is represented by the symbol | h |
Minutes is represented by the symbol | min |
Seconds is represented by the symbol | s |
Microsecond is represented by the symbol | µs |
Meter is represented by the symbol | m |
Feet is represented by the symbol | ft |
Kilometer is represented by the symbol | km |
Kilogram is represented by the symbol | kg |
Pound is represented by the symbol | lb |

Answer to Problem 2.1P
In
Explanation of Solution
In one day there are twenty-four hours and in one hour there are sixty minutes.
In one pound there are 0.453593 kg and in one feet there are 0.3048 m. Convert meter per day into kilogram to feet per minute into pound as follows:
Want to see more full solutions like this?
Chapter 2 Solutions
Elementary Principles of Chemical Processes, Binder Ready Version
- 2/1000kg/h of an acetone - water mixture containing 20wt% by weight of acetone is to be counter currently extracted with trichloroethane. The recovered solvent to be used is free from acetone. The water and trichloroethane are insoluble. If 90% recovery of acetone is desired estimate the number of stages required if 1.5 times the minimum solvent is used. The kg acetone/kg extract=1.65 kg water/kg raffinate. a- Repeat the calculation of A if the solvent used has purity of 98.5%. b- If co-current extractor is used instead of counter-current extractor in A and B estimate the number of stages required if equal amount of solvent used in each stage.arrow_forwardWater is pumped from a large reservoir to a point 75 feet higher than the reservoir. How many feet of head must be added by the pump if 7600 lbm/hr flows through a 6-inch pipe and the frictional head loss is 3 feet? The density of the fluid is 60 lbm/ft³ and the pump efficiency is 70%. Assume the kinetic energy correction factor equals 1.arrow_forwardA firefighter is using a large water tank to supply water for extinguishing a fire. The tank has a small hole at the bottom, and water is leaking out due to gravity. The hole is located 2.5 meters below the water surface inside the tank. a. Determine the speed at which the water exits the hole. Assume there is no air resistance and that the water flow is ideal (neglect viscosity and turbulence). b. If the hole has a diameter of 2 cm, calculate the flow rate (discharge rate) in liters per second.arrow_forward
- What kind of boundary must a system have to undergo the stated Interaction with its surroundings if possible ( mention the 3 qualities of the boundary in each case A. WORK INTERACTIONS ONLY B. MASS AND HEAT INTERACTIONS ONLY C. HEAT INTERACTIONS ONLY IS THIS POSSIBLE, EXPLAIN. D. WORK AND MASS INTERACTIONS ONLY. E. WORK AND HEAT INTERACTIONS ONLY F. MASS INTERACTIONS ONLY. IS THIS POSSIBLE OR NOT. EXPLAINarrow_forwardAnswer the questionsarrow_forwardFigure below shows a portion of a fire protection system in which apump draws water at 60 F from a reservoir and delivers it to point B at the flow rate of 1500 gal/min a). Calculate the required height of the water level in the tank in order to maintain 5.0 psig pressure at point A. Answer: h = 12,6 ft b). Assuming that the pressure at A is 5.0 psig, calculate the power delivered by the pump to the water in order to maintain the pressure at point B at 85 kPa. Include energy lost due to friction but neglect any other energy losses. P₁ =19,2 hparrow_forward
- Water at 60° F is being pumped from a stream to a reservoir whose surface is 210 ft above the pump. The pipe from the pump to the reservoir is an 8-in Schedule 40 steel pipe 2500 ft long. The pressure at the pump inlet is - 2,36 psig. If 4.00 ft³/s is being pumped, a). Compute the pressure at the outlet of the pump. Answer: 0,997 MPa b). Compute the power delivered by the pump to the water. Answer: 151 hp Consider the friction loss in the discharged line, but neglect other lossesarrow_forward1. Consider a mixture of 2.5.0% ethane, 2.0% butane, and 1.7% n-pentane by volume.a. Estimate the LFL and UFL of the mixture. Is it flammable?b. Estimate the LOC for this mixture.arrow_forwardEstimate the LFL and UFL for propylene using Equations 6-10 and 6-11 in the textbook,and compare these to the experimental values given in the table in Appendix B.arrow_forward
- 1. Determine the minimum compression ratio required to raise the temperature of air overhexane to its AIT. Assume an initial temperature of 20°C.2. Ethanol is kept in a storage vessel that is vented with air (at 25°C and 1 atm). Is theequilibrium mixture of vapor above the liquid and air flammable? What if the liquid isacetone instead?arrow_forwardHydrogenation of Ethylbenzene to Styrene Reaction: C₈H₁₀ → C₈H₈ + H₂ΔHᵣ°(300°C) = -124 kJ/mol (exact value unknown) Process Description: The basis is 1000 kg/h of separated styrene. The reaction conversion rate is 35%. The temperature increase in heat exchanger 2 is adiabatic. A fresh stream of pure ethylbenzene (25°C) enters a mixing vessel, where it is combined with a recycle stream (from the distillation column, as explained later), which also consists of pure ethylbenzene at 25°C. After mixing, the stream is sent to a heat exchanger (HX1), where the mixture is heated to 200°C. Next, the mixture enters an adiabatic heat exchanger (HX2), where it is further heated to 300°C by adding steam (at 350°C). This steam is used to prevent side reactions and carbon deposition in the reactor. The heated mixture is then fed into the reactor, where the reaction takes place with a conversion rate of 35%. As a result, the mixture cools down to 260°C. The resulting mixture is then sent to HX4, where…arrow_forwardChemical Engineering Questionarrow_forward
- Introduction to Chemical Engineering Thermodynami...Chemical EngineeringISBN:9781259696527Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark SwihartPublisher:McGraw-Hill EducationElementary Principles of Chemical Processes, Bind...Chemical EngineeringISBN:9781118431221Author:Richard M. Felder, Ronald W. Rousseau, Lisa G. BullardPublisher:WILEYElements of Chemical Reaction Engineering (5th Ed...Chemical EngineeringISBN:9780133887518Author:H. Scott FoglerPublisher:Prentice Hall
- Industrial Plastics: Theory and ApplicationsChemical EngineeringISBN:9781285061238Author:Lokensgard, ErikPublisher:Delmar Cengage LearningUnit Operations of Chemical EngineeringChemical EngineeringISBN:9780072848236Author:Warren McCabe, Julian C. Smith, Peter HarriottPublisher:McGraw-Hill Companies, The





