Study Guide with Lab Manual for Jeffus' Welding: Principles and Applications, 8th
8th Edition
ISBN: 9781305494701
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 1R
What is the key to preventing accidents in a welding shop?
Expert Solution & Answer
To determine
The key to prevent accidents in a welding shop.
Explanation of Solution
The key to prevent accidents in a welding shop are:
- Necessary protection must be taken while welding process otherwise it will harm the welder.
- Safety precautions must be taken. The safety precautions are mentioned on the manual of every equipment.
- There is no substitute to caution and common sense so each person take personal responsibility for their own safety and safety of others on the job.
- Follow all the safety rules, regulation and procedure of welding areas.
- Never engage in horseplay or practical jokes while at work.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
4-105. Replace the force system acting on the beam by an equivalent resultant force and couple
moment at point B.
A
30 in.
4 in.
12 in.
16 in.
B
30%
3 in.
10 in.
250 lb
260 lb
13
5
12
300 lb
Sketch and Describe a hatch coaming and show how the hatch coamings are framed in to ships strucure?
Sketch and describe hatch coamings. Describe structrual requirements to deck plating to compensate discontinuity for corners of a hatch. Show what is done to the deck plating when the decks are cut away and include the supporting members.
Chapter 2 Solutions
Study Guide with Lab Manual for Jeffus' Welding: Principles and Applications, 8th
Ch. 2 - What is the key to preventing accidents in a...Ch. 2 - Who is ultimately responsible for the welder’s...Ch. 2 - Describe the three classifications of burns.Ch. 2 - What emergency steps should be taken to treat...Ch. 2 - List the three types of light that may be present...Ch. 2 - Which type of light is the most likely to cause...Ch. 2 - What can be done on the job site to reduce the...Ch. 2 - What is the name of the eye burn that can occur in...Ch. 2 - In what two ways can ultraviolet light burn the...Ch. 2 - Why is it important to seek medical treatment for...
Ch. 2 - What fabric(s) are the best choice to wear as...Ch. 2 - Describe the ideal work shirt, pants, boots, and...Ch. 2 - Why is it unsafe to carry butane lighters or...Ch. 2 - What special protective items can be worn to...Ch. 2 - Why must eye protection be worn at all times in...Ch. 2 - What types of injuries can occur to the ears...Ch. 2 - What types of protection are available to protect...Ch. 2 - What types of information should be covered in a...Ch. 2 - Name two types of respirators and describe how...Ch. 2 - List the materials that can give off dangerous...Ch. 2 - Why must metal that has been used before be...Ch. 2 - Under what conditions can natural ventilation be...Ch. 2 - Name two advantages of recycling scrap metal.Ch. 2 - When must forced ventilation be used?Ch. 2 - Who must be provided with safety data sheets...Ch. 2 - Describe an acceptable storage area for a cylinder...Ch. 2 - How must high-pressure gas cylinders be stored so...Ch. 2 - What should be done with a leaking cylinder if the...Ch. 2 - Why is it important for acetylene cylinders to not...Ch. 2 - What is hot work?Ch. 2 - How far away should highly combustible materials...Ch. 2 - When is a fire watch needed?Ch. 2 - List the four types of fire extinguishers and the...Ch. 2 - Why is it important to have a planned maintenance...Ch. 2 - Why is it important to keep a welding area clean?Ch. 2 - What should you do if you have to leave a piece of...Ch. 2 - Why must a mushroomed chisel or hammer be...Ch. 2 - What causes most electric shock in the welding...Ch. 2 - According to the Welding Safety Checklist in...Ch. 2 - What can happen if too much power is being carried...Ch. 2 - Why must equipment be turned off and unplugged...Ch. 2 - According to Table 2-2, what gauge wire size would...Ch. 2 - What is a GFCI?Ch. 2 - List five safety tips for safe extension cord use.Ch. 2 - List 10 safety rules for the safe use of portable...Ch. 2 - Why is it important to not weld when everything is...Ch. 2 - List two types of grinders used by welders.Ch. 2 - How close to the grinding stone face should the...Ch. 2 - Name metal cutting machines used in the welding...Ch. 2 - Describe how a person should safely lift a heavy...Ch. 2 - List the things that should be inspected on a...Ch. 2 - List and explain five ladder use safety rules.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An Inclining experiment done on a ship thats 6500 t, a mass of 30t was moved 6.0 m transvesly causing a 30 cm deflection in a 6m pendulum, calculate the transverse meta centre height.arrow_forwarda ship 150 m long and 20.5 m beam floats at a draught of8 m and displaces 19 500 tonne. The TPC is 26.5 and midshipsection area coefficient 0.94. Calculate the block, prismatic andwaterplane area coefficients.arrow_forwardA vessel loads 680 t fuel between forward and aft deep tanks. centre of gravity of forward tank is 24m forward of ships COG. centre to centre between tanks is 42 m. how much in each tank to keep trim the samearrow_forward
- Beam of a vessel is 11% its length. Cw =0.72. When floating in SW of relative denisity 1.03, TPC is 0.35t greater than in freshwater. Find the length of the shiparrow_forwardAn inclining experiment was carried out on a ship of 4000tonne displacement, when masses of 6 tonne were moved transverselythrough 13.5 m. The deflections of a 7.5 m pendulurnwere 81, 78, 85, 83, 79, 82, 84 and 80 mm respectively.Caiculate the metacentric height.arrow_forwardA ship of 10 000 tonne displacement has a waterplanearea of 1300 m2. The ship loads in water of 1.010 t/m3 andmoves into water of 1.026 t/m3. Find the change in meandraughtarrow_forward
- A ship of 7000 tonne displacement has a waterplane areaof 1500 m2. In passing from sea water into river water of1005 kg/m3 there is an increase in draught of 10 cm. Find the Idensity of the sea water.arrow_forwardA ship has 300 tonne of cargo in the hold, 24 m forward ofmidships. The displacement of the vessel is 6000 tonne and its centre of gravity is 1.2 m forward of midships.Find the new position of the centre of gravity if this cargo ismoved to an after hold, 40 m from midshipsarrow_forwardSketch and describe how ships are supported in dry dock. When and where does the greatest amount of stresses occur?arrow_forward
- Sketch and desribe a balanced rudder and how it is suspendedarrow_forwardA ship 140 m long and 18 m beam floats at a draught of9 m. The immersed cross-sectionai areas at equai intervais are 5,60, 116, 145, 152, 153, 153, 151, 142, 85 and 0 m2 respectively.Calculate:(a) displacement(b) block coefficient(c) midship section area coefficient(d) prismatic coefficient.arrow_forwardA steamer has waterplane area 1680m2 recorded in water with relative denisty 1.013. Displacement = 1200 t, calculate difference in draught in salwater reltive denisity 1.025.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY